SRSofia Rahiminejad

Sofia Rahiminejad

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Sofia Rahiminejad has a total of 52 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Flat Silicon Gradient Index Lens With Deep Reactive-Ion-Etched Three-Layer Antireflection Structure for Millimeter and Submillimeter Wavelengths

    by Fabien Defrance, Cecile Jung-Kubiak, John Gill, Sofia Rahiminejad, Theodore Macioce, Jack Sayers, Goutam Chattopadhyay, Sunil R. Golwala

    We present the design, fabrication, and characterization of a 100 mm diameter, flat, gradient-index (GRIN) lens fabricated with high-resistivity silicon, combined with a three-layer anti-reflection (AR) structure optimized for 160–355 GHz. Multi-depth, deep reactive-ion etching (DRIE) enables patterning of silicon wafers with sub-wavelength structures (posts or holes) to locally change the effective refractive index and thus create anti-reflection layers and a radial index gradient. The structures are non-resonant and, for sufficiently long wavelengths, achromatic. Hexagonal holes varying in size with distance from the optical axis create a parabolic index profile decreasing from 3.15 at the center of the lens to 1.87 at the edge. The AR structure consists of square holes and cross-shaped posts. We have fabricated a lens consisting of a stack of five 525 μm thick GRIN wafers and one AR wafer on each face. We have characterized the lens over the frequency range 220–330 GHz, obtaining behavior consistent with Gaussian optics down to —14 dB and transmittance between 75% and 100%.


  • MEMS Phase Shifters for THz Beam-Scanning: Demonstration With a 500–600 GHz Phased Array With Leaky-Wave Feeds

    by Sven van Berkel, Subash Khanal, Sofia Rahiminejad, Cecile Jung-Kubiak, Alain Eric Maestrini, Goutam Chattopadhyay

    Beam-scanning capabilities for space-borne submillimeter-wave spectrometers are critical for instrument calibration and field-of-view mapping. However, the lack of low-loss waveguide-integrated phase shifters above 500 GHz has been a significant challenge for realizing Terahertz phased array antennas. Recently developed MEMS-actuated phase shifters have emerged as promising candidates, initially demonstrating a 145 ${}^\circ$ phase shift. As a first demonstration of the efficacy of these phase shifters for electronic beam-steering, we present the design, fabrication, and characterization of a linear, near-Nyquist sampled, 4x1-element phased array operating from 500-600 GHz. The array element is a silicon micro-machined leaky-wave feed based on a Fabry-Pérot cavity to enhance directivity and reduce grating lobes while achieving bandwidth requirements with minimal scan loss. It is shown, through measurements, that this antenna feed is suitable for use in larger 8x1-element arrays for applications that require moderate gain (20 dBi) and scanning ( $\pm 20^\circ$ ) with a fan beam. Furthermore, we present measurement results of a second generation of MEMS phase shifters with an increased measured phase shift up to 350 ${}^\circ$ . A full 360 ${}^\circ$ phase-wrapping capability is desired as this will enable high-gain lens-scanning phased arrays that can be used for future submillimeter-wave spectrometers.


  • 500-750 GHz Contactless Rotating MEMS Single-Pole Double-Throw Waveguide Switch

    by Sofia Rahiminejad, Sven van Berkel, Robert Lin, Subash Khanal, Cecile Jung-Kubiak, Goutam Chattopadhyay, Mina Rais-Zadeh

    This paper presents a Single-Pole Double-Throw MEMS waveguide switch operating at $500-750~GHz$ . The switch consist of a U-bend waveguide surrounded by an electromagnetic bandgap (EBG) surface. The EBG surface is used to isolate the electromagnetic wave without mechanical or electrical contact. The U-bend is placed on a rotating arm, that moves between two positions. The arms movement is controlled by a rotating MEMS motor that can rotate $\pm 4.5^\circ$ at $70~V$ . The switch is fabricated using silicon micromachining and is designed to be in-plane with the connecting waveguides. This allows it to be implemented into a silicon micromachined waveguide network. The waveguide switch has a measured insertion loss less than $2.5~dB$ and an isolation larger than $30~dB$ between $550-750~GHz$ . Since the electromagnetic wave can be routed with the EBG surface instead of needing electrical or mechanical contact, the MEMS waveguide switch can operate without the need for mechanical contact and avoids common MEMS switch issues such as stiction between the switch and its ports. 2024-0059


  • A Waveguide-Based Variable Attenuator for Terahertz Applications

    by Subash Khanal, Sofia Rahiminejad, Choonsup Lee, Jacob Willem Kooi, Robert Lin, Goutam Chattopadhyay

    This article presents a novel waveguide-based terahertz (THz) variable attenuator, integrated with a piezo-electric motor, to achieve precise and fine step values of signal attenuation. A low-resistivity silicon slab, coated with a thin layer of Titanium metal, is inserted inside a waveguide that absorbs some of the electromagnetic waves traveling through the guide. Impedance matching is achieved by gradually perforating the silicon slab and thus, creating variable impedance needed for matching. The amount of signal absorbed by the slab is determined by the sheet resistance value of the metal coating and the position of the slab in the waveguide. A miniature nanometer-scale precision piezo electric motor is used for precise control of the signal attenuation. In this work, we present the attenuator design for a frequency band of 500-750 GHz where up to 40 dB of signal attenuation was achieved, using a 1.75 mm long silicon slab with a 25 nm Titanium metal coating. The presented variable attenuator design offers compactness, scalability, and easy integration with THz sources and receivers. Furthermore, the compact size and low power consumption open up possibilities for implementation on CubeSat/Smallsat/Drone-based platforms, further expanding its potential space applications.


  • A 250–310 GHz Piezo-Motor Actuated SPDT Waveguide Switch With High Isolation

    by Sven van Berkel, Sofia Rahiminejad, Robert Lin, Goutam Chattopadhyay

    The design and performance of a sub-Terahertz (THz) single-pole double-throw (SPDT) waveguide switch is presented, operating from $\rm{250 \,GHz}$ to $\rm{310 \,GHz}$ . The piezo-motor actuated switch is suitable for high-fidelity calibration of THz spectroscopy and radiometry instruments, thanks to its low insertion loss, $\rm{< -0.6 \,dB}$ , low return loss, $\rm{< -20 \,dB}$ , and high isolation, $\rm{< -75 \,dB}$ . The high isolation and low leakage is achieved by using an array of rectangular metal pillars surrounding the waveguide apertures, that act as an electromagnetic band gap (EBG) structure in the proximity of the switching element. The switching element is controlled with micro-metric precision to direct the signal through a U-bend waveguide to either one of the two output waveguide apertures. The reliability and durability of the switch is tested by performing one million switch actions at its maximum switching rate of $\rm{1 Hz}$ , resulting in a mean positioning error better than $\rm{2\, \mu m}$ .


  • A Low-Loss Silicon MEMS Phase Shifter Operating in the 550-GHz Band

    by Sofia Rahiminejad, Maria Alonso-Delpino, Theodore J. Reck, Alejandro Peralta, Robert Lin, Cecile Jung-Kubiak, Goutam Chattopadhyay

    This article presents a low-loss silicon microelectrical mechanical system (MEMS) phase shifter operating in the 500-600 GHz band. The phase shifter consists of a 30-μm thick perforated silicon slab that is moved in and out of a waveguide in the E-plane with a large deflection MEMS actuator. By implementing different hexagonal patterns in the silicon slab, a stepped permittivity is created to impedance match, and thus, reduce return loss. When the silicon slab is inserted into the waveguide, the phase velocity of the incoming wave is decreased, thus resulting in different phase shifts depending on the position of the slab inside the waveguide. The MEMS phase shifter is fully actuated at around 50 V and can move up to ±95 μm, depending on the applied voltage. The insertion loss, when the maximum phase shift is achieved, is measured to be 1.8 dB, compared to a 1.6-dB insertion loss for a waveguide of equivalent length. The return loss is better than 18 dB for the desired band. The measured phase shift, with the slab fully inserted into the waveguide at 550 GHz was 145 ° . The MEMS phase shifter enables a variety of applications including phased array antenna systems with scanning capability for mapping of planetary surfaces with an electronically steerable antenna.


  • Open Access

    Dry Film Photoresist-Based Microfabrication: A New Method to Fabricate Millimeter-Wave Waveguide Components

    by Sadia Farjana, Mohamadamir Ghaderi, Sofia Rahiminejad, Sjoerd Haasl, Peter Enoksson

    This paper presents a novel fabrication method based on dry film photoresists to realize waveguides and waveguide-based passive components operating at the millimeter-wave frequency (30–300 GHz). We demonstrate that the proposed fabrication method has a high potential as an alternative to other microfabrication technologies, such as silicon-based and SU8-based micromachining for realizing millimeter-wave waveguide components. Along with the nearly identical transfer of geometrical structures, the dry film photoresist offers other advantages such as fewer processing steps, lower production cost, and shorter prototyping time over the conventional micromachining technologies. To demonstrate the feasibility of the fabrication process, we use SUEX dry film to fabricate a ridge gap waveguide resonator. The resonator is designed to exhibit two resonances at 234.6 and 284 GHz. The measured attenuation at 234 GHz is 0.032 dB/mm and at 283 GHz is 0.033 dB/mm for the fabricated prototype. A comparative study among different existing technologies indicates that the reported method can give a better unloaded Q-value than other conventional processes. The measured unloaded Q-values are in good agreement with the simulated unloaded Q-values. The signal attenuation indicates that SUEX dry film photoresists can be used to fabricate passive devices operating at millimeter-wave frequencies. Moreover, this new fabrication method can offer fast and low-cost prototyping.


  • Open Access

    Evaluation of 3D printed materials used to print WR10 horn antennas

    by Elof Köhler, Sofia Rahiminejad, Peter Enoksson

    A WR10 waveguide horn antenna is 3D printed with three different materials. The antennas are printed on a fusion deposition modeling delta 3D printer built in house at Chalmers University of Technology. The different plastic materials used are an electrically conductive Acrylonitrile butadiene styrene (ABS), a thermally conductive polylactic acid containing 35% copper, and a tough Amphora polymer containing at least 20% carbon fiber. The antennas are all printed with a 0.25 mm nozzle and 100 μm layer thickness and the software settings are tuned to give maximum quality for each material. The three 3D printed horn antennas are compared when it comes to cost, time and material properties.


  • Open Access

    Direct 3D printed shadow mask on Silicon

    by S Rahiminejad, E Köhler, P Enoksson

    A 3D printed shadow mask method is presented. The 3D printer prints ABS plastic directly on the wafer, thus avoiding gaps between the wafer and the shadow mask, and deformation during the process. The wafer together with the 3D printed shadow mask was sputtered with Ti and Au. The shadow mask was released by immersion in acetone. The sputtered patches through the shadow mask were compared to the opening of the 3D printed shadow mask and the design dimensions. The patterned Au patches were larger than the printed apertures, however they were smaller than the design widths. The mask was printed in 4 min, the cost is less than one euro cent, and the process is a low temperature process suitable for temperature sensitive components.


  • A four level silicon microstructure fabrication by DRIE

    by S Rahiminejad, P Cegielski, M Abassi, P Enoksson

    We present a four level Si microstructure fabrication process with depths ranging from 70–400 μ m. All four levels are etched from the same side, by using four hard masks ( S i O 2 , Al, AZ4562 photo resist, and Al). The choice of the hard masks and their relative selectivity will be discussed. Also two different deep reactive ion etching (DRIE) processes, performed in two different machines, are compared and evaluated. The process evaluation and discussions are based on the vertical walls deviation from a right angle, the surface roughness and the resolution. In the end, a solution is proposed to remove spikes and grassing which appeared during both DRIE processes, and the impact of removing them from the surfaces is discussed.