Anton I. Gusev
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Anton I. Gusev has a total of 66 co-authors. Here are the top co-authors by number of shared publications:
- Antoine Silvestre de Ferron
Université de Pau Et Des Pays de L’Adour, SIAME, Pau, France
11 shared publications - Laurent Pecastaing
Université de Pau Et Des Pays de L’Adour, SIAME, Pau, France
11 shared publications - Sergei N. Rukin
Institute of Electrophysics, UB, RAS, Yekaterinburg 620016, Russia
11 shared publications S. N. Tsyranov
Institute of Electrophysics, UB, RAS, Yekaterinburg 620016, Russia
8 shared publications- Bucur Mircea Novac
Wolfson School of Mechanical, Electrical and Manufacturing Engineering, Loughborough University, Loughborough, U.K.
6 shared publications M. S. Pedos
Institute of Electrophysics, UB, RAS, Yekaterinburg 620016, Russia
6 shared publications
Latest Publications
- 9 June 2025
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 43 (4)
Secondary ion mass spectrometry as a tool to analyze semiconductor opening switch diodes
This paper presents a secondary ion mass spectrometry (SIMS) method for the analysis of semiconductor opening switch (SOS) diodes, which are crucial in nanosecond pulsed power systems. The study addresses the gap in experimental measurements of doping concentration in SOS diodes, as the current literature contains mainly theoretical doping profiles. The development of a reliable method for measuring doping concentration is expected to advance SOS technology, given the limited number of manufacturers. The SIMS technique is used to determine the depth distribution and concentration of dopants. The method is adapted to study boron, aluminum, and phosphorus in silicon, with emphasis on detection over several hundred micrometers to clarify the doping profile of SOS diodes. The experimental procedure includes (i) preparation of the SOS diode sample by cutting, polishing, and gold plating; (ii) performing dynamic SIMS analysis using specific conditions for boron/aluminum (O2+/M+) and phosphorus (Cs+/M−) detection; and (iii) using a line scan mode to measure element intensities across the sample, with quantification based on reference samples. The developed SIMS conditions enabled the measurement of the depth distribution of the dopants over a range of 1150 μm with a 2 μm step and providing sufficient lateral resolution. The quantified profiles of boron, aluminum, and phosphorus in the SOS diode are presented. The experimental impurity profiles were in partial agreement with the theoretical doping profiles. This method provides access to the analysis of semiconductor devices with thick structures, which are commonly used in power electronics and solid-state pulsed power.
- 9 June 2025
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 43 (4)
Secondary ion mass spectrometry as a tool to analyze semiconductor opening switch diodes
This paper presents a secondary ion mass spectrometry (SIMS) method for the analysis of semiconductor opening switch (SOS) diodes, which are crucial in nanosecond pulsed power systems. The study addresses the gap in experimental measurements of doping concentration in SOS diodes, as the current literature contains mainly theoretical doping profiles. The development of a reliable method for measuring doping concentration is expected to advance SOS technology, given the limited number of manufacturers. The SIMS technique is used to determine the depth distribution and concentration of dopants. The method is adapted to study boron, aluminum, and phosphorus in silicon, with emphasis on detection over several hundred micrometers to clarify the doping profile of SOS diodes. The experimental procedure includes (i) preparation of the SOS diode sample by cutting, polishing, and gold plating; (ii) performing dynamic SIMS analysis using specific conditions for boron/aluminum (O2+/M+) and phosphorus (Cs+/M−) detection; and (iii) using a line scan mode to measure element intensities across the sample, with quantification based on reference samples. The developed SIMS conditions enabled the measurement of the depth distribution of the dopants over a range of 1150 μm with a 2 μm step and providing sufficient lateral resolution. The quantified profiles of boron, aluminum, and phosphorus in the SOS diode are presented. The experimental impurity profiles were in partial agreement with the theoretical doping profiles. This method provides access to the analysis of semiconductor devices with thick structures, which are commonly used in power electronics and solid-state pulsed power.
- 6 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 53 (7) , 1583-1591
Experimental and Numerical Simulation Study of a Semiconductor Opening Switch
This article examines the nanosecond interruption of high current in semiconductor opening switch (SOS) diodes, with the goal of bridging the gap between experimental results and numerical simulations. The experimental results of SOS diodes (0.25 cm2, 0.9 kV) operating as a nanosecond interrupter are presented in a wide range of cut-off current density from 300 A/cm2 to 5 kA/cm2 to analyze the two modes of operation, i.e., drift step recovery diode (DSRD) and SOS. In addition, the numerical simulations of the SOS diode are conducted to investigate the dynamics of the SOS diode in the DSRD and the SOS modes using the Synopsys TCAD. A mixed-mode device with a circuit simulator is utilized to simulate the SOS effect and the dynamic processes occurring during the current cut-off stage. Finally, the experimental and numerical simulation results of the SOS current and load voltage are compared indicating: 1) the accuracy of the TCAD model in the commercially available software, and 2) the possibility of operating the SOS diode in a DSRD mode.
- 6 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 53 (7) , 1583-1591
Experimental and Numerical Simulation Study of a Semiconductor Opening Switch
This article examines the nanosecond interruption of high current in semiconductor opening switch (SOS) diodes, with the goal of bridging the gap between experimental results and numerical simulations. The experimental results of SOS diodes (0.25 cm2, 0.9 kV) operating as a nanosecond interrupter are presented in a wide range of cut-off current density from 300 A/cm2 to 5 kA/cm2 to analyze the two modes of operation, i.e., drift step recovery diode (DSRD) and SOS. In addition, the numerical simulations of the SOS diode are conducted to investigate the dynamics of the SOS diode in the DSRD and the SOS modes using the Synopsys TCAD. A mixed-mode device with a circuit simulator is utilized to simulate the SOS effect and the dynamic processes occurring during the current cut-off stage. Finally, the experimental and numerical simulation results of the SOS current and load voltage are compared indicating: 1) the accuracy of the TCAD model in the commercially available software, and 2) the possibility of operating the SOS diode in a DSRD mode.
- 4 June 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 52 (9) , 4332-4340
Experimental and Simulation Study of Parallel-Connected Thyristors in Impact-Ionization Switching Mode
This article investigates the impact-ionization switching mechanism in parallel-connected high-voltage thyristors, aiming to bridge the gap between experimental observations and numerical simulations. A novel experimental setup is designed to study four parallel thyristors triggered in impact-ionization wave mode, marking the first instance of such an arrangement. In addition to the experiment, a numerical simulation is used to assess the impact-ionization switching of high-voltage thyristors in parallel connection. The numerical simulation adopts a quasi-3-D model of the thyristor structure derived from a 2-D model, considering cylindrical symmetry. Three distinct scenarios are explored in the simulation: 1) static voltage breakdown; 2) suppression of unwanted ${d}V/{d}t$ triggering; and 3) delayed impact-ionization breakdown. The article presents a detailed comparison and discussion of the experimental and numerical simulation results related to impact-ionization switching.
- 4 June 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 52 (9) , 4332-4340
Experimental and Simulation Study of Parallel-Connected Thyristors in Impact-Ionization Switching Mode
This article investigates the impact-ionization switching mechanism in parallel-connected high-voltage thyristors, aiming to bridge the gap between experimental observations and numerical simulations. A novel experimental setup is designed to study four parallel thyristors triggered in impact-ionization wave mode, marking the first instance of such an arrangement. In addition to the experiment, a numerical simulation is used to assess the impact-ionization switching of high-voltage thyristors in parallel connection. The numerical simulation adopts a quasi-3-D model of the thyristor structure derived from a 2-D model, considering cylindrical symmetry. Three distinct scenarios are explored in the simulation: 1) static voltage breakdown; 2) suppression of unwanted ${d}V/{d}t$ triggering; and 3) delayed impact-ionization breakdown. The article presents a detailed comparison and discussion of the experimental and numerical simulation results related to impact-ionization switching.
- 3 June 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 52 (7) , 2868-2876
A 500-kV Nanosecond Pulse Generator Based on an Off-the-Shelf Solid-State Opening Switch
This article investigates the use of off-the-shelf (OTS) diodes as opening switches in a 500-kV nanosecond pulsed power generator. A 40-J test bench based on a saturable pulse transformer and a primary thyratron switch is designed to evaluate the performance of the OTS diodes in comparison with standard semiconductor opening switch (SOS) diodes A distinguishing feature of the proposed circuit is the adjustability of the output pulse energy, which is achieved using flat hysteresis loop magnetic cores and variable reset magnetic field. The study confirms the operation of OTS diodes as an opening switch, although highlighting differences in the reverse current conduction that affect the generated voltage pulse characteristics. Based on the successful operation of the OTS diodes, a 500-kV pulsed power generator using an OTS Solid-State Opening Switch (GO-SSOS) is developed. The GO-SSOS provides output voltages of 100–500 kV across resistive loads from 50 $\Omega$ to 1 k $\Omega$ , with a pulse width of about 100 ns and a rise time of less than 40 ns. The generator achieves a peak power of 335 MW and demonstrates an overall energy efficiency in the range of 30%–70% depending on the load. Operation at a pulse repetition rate of 60 Hz is presented, showing a good reproducibility of the pulses with an amplitude and duration deviation of about 2% and 10%, respectively. No degradation of the OTS diodes has been observed after the tests (more than 1000 pulses). As an example of the possible applications of the GO-SSOS, corona discharge in the air is performed, also proving the stability of all the systems under conditions of strong electromagnetic interference.
- 3 June 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 52 (7) , 2868-2876
A 500-kV Nanosecond Pulse Generator Based on an Off-the-Shelf Solid-State Opening Switch
This article investigates the use of off-the-shelf (OTS) diodes as opening switches in a 500-kV nanosecond pulsed power generator. A 40-J test bench based on a saturable pulse transformer and a primary thyratron switch is designed to evaluate the performance of the OTS diodes in comparison with standard semiconductor opening switch (SOS) diodes A distinguishing feature of the proposed circuit is the adjustability of the output pulse energy, which is achieved using flat hysteresis loop magnetic cores and variable reset magnetic field. The study confirms the operation of OTS diodes as an opening switch, although highlighting differences in the reverse current conduction that affect the generated voltage pulse characteristics. Based on the successful operation of the OTS diodes, a 500-kV pulsed power generator using an OTS Solid-State Opening Switch (GO-SSOS) is developed. The GO-SSOS provides output voltages of 100–500 kV across resistive loads from 50 $\Omega$ to 1 k $\Omega$ , with a pulse width of about 100 ns and a rise time of less than 40 ns. The generator achieves a peak power of 335 MW and demonstrates an overall energy efficiency in the range of 30%–70% depending on the load. Operation at a pulse repetition rate of 60 Hz is presented, showing a good reproducibility of the pulses with an amplitude and duration deviation of about 2% and 10%, respectively. No degradation of the OTS diodes has been observed after the tests (more than 1000 pulses). As an example of the possible applications of the GO-SSOS, corona discharge in the air is performed, also proving the stability of all the systems under conditions of strong electromagnetic interference.
- 29 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 52 (9) , 4286-4293
Series–Parallel Connection of Thyristors Triggered in Impact-Ionization Wave Mode
This article demonstrates the impact-ionization switching of standard thyristors in a series-parallel configuration. The series–parallel triggering of thyristors holds a substantial promise for enhancing both voltage blocking and current capacity of the switch simultaneously. Nevertheless, the key obstacle in this context revolves around acquiring a suitable trigger generator, primarily because this trigger necessitates a combination of high $dV/dt$ and low post-triggering energy to be applied to the thyristor assembly. Thus, a novel trigger circuit is developed to test a setup with two parallel branches, each having two series-connected thyristors (with a wafer diameter of Ø24 mm and a rated blocking voltage of 1.8 kV). These thyristors were tested in the impact-ionization switching mode using a single Marx generator. We conducted experiments in a current flow phase, where energy switching occurred by connecting an $RLC$ discharge circuit. These experiments revealed that the thyristors transitioned from a blocking to a conducting state around $\sim$ 400 ps, enabling the switching of a current pulse with an amplitude of $\sim$ 17.5 kA and a $dI/dt$ of $\sim$ 8.5 kA/ $\mu$ s (limited by the circuit). Notably, the current imbalance between the thyristor parallel branches remained under 2%. To the best of our knowledge, this is the first reported instance of successfully triggering high-voltage thyristors connected in series–parallel in the impact-ionization wave mode.
- 29 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 52 (9) , 4286-4293
Series–Parallel Connection of Thyristors Triggered in Impact-Ionization Wave Mode
This article demonstrates the impact-ionization switching of standard thyristors in a series-parallel configuration. The series–parallel triggering of thyristors holds a substantial promise for enhancing both voltage blocking and current capacity of the switch simultaneously. Nevertheless, the key obstacle in this context revolves around acquiring a suitable trigger generator, primarily because this trigger necessitates a combination of high $dV/dt$ and low post-triggering energy to be applied to the thyristor assembly. Thus, a novel trigger circuit is developed to test a setup with two parallel branches, each having two series-connected thyristors (with a wafer diameter of Ø24 mm and a rated blocking voltage of 1.8 kV). These thyristors were tested in the impact-ionization switching mode using a single Marx generator. We conducted experiments in a current flow phase, where energy switching occurred by connecting an $RLC$ discharge circuit. These experiments revealed that the thyristors transitioned from a blocking to a conducting state around $\sim$ 400 ps, enabling the switching of a current pulse with an amplitude of $\sim$ 17.5 kA and a $dI/dt$ of $\sim$ 8.5 kA/ $\mu$ s (limited by the circuit). Notably, the current imbalance between the thyristor parallel branches remained under 2%. To the best of our knowledge, this is the first reported instance of successfully triggering high-voltage thyristors connected in series–parallel in the impact-ionization wave mode.
- 30 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 51 (10) , 2849-2857
A Saturable Pulse Transformer Based on Nanocrystalline Magnetic Cores for an Adjustable Nanosecond High-Voltage Generator
This article is devoted to saturable pulse transformers (SPTs), combining the functions of a pulse transformer and a magnetic switch. Two nanocrystalline magnetic cores are investigated in the SPT of an inductive energy storage (IES) pulsed power system based on a semiconductor opening switch (SOS). The first magnetic core has a square hysteresis loop (Br/Bsat $>$ 90%), while the second core has a flat hysteresis loop (Br/Bsat $\sim$ 4%). A test bench with an initially stored energy of 10 J is developed. The circuit design is discussed, and the magnetic materials are compared. Based on the features of the hysteresis loops, two nanosecond high-voltage (HV) SOS generators are tested, with the output voltage adjusted by tuning the input voltage and controlling the bias magnetic field. The influence of the optimal core saturation on the operation of the SOS diode is studied. An adjustable output voltage impulse of more than 200 kV amplitude with a 16 ns rise time is demonstrated on a 1 $\text{k}\Omega$ resistive load.
- 30 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 51 (10) , 2849-2857
A Saturable Pulse Transformer Based on Nanocrystalline Magnetic Cores for an Adjustable Nanosecond High-Voltage Generator
This article is devoted to saturable pulse transformers (SPTs), combining the functions of a pulse transformer and a magnetic switch. Two nanocrystalline magnetic cores are investigated in the SPT of an inductive energy storage (IES) pulsed power system based on a semiconductor opening switch (SOS). The first magnetic core has a square hysteresis loop (Br/Bsat $>$ 90%), while the second core has a flat hysteresis loop (Br/Bsat $\sim$ 4%). A test bench with an initially stored energy of 10 J is developed. The circuit design is discussed, and the magnetic materials are compared. Based on the features of the hysteresis loops, two nanosecond high-voltage (HV) SOS generators are tested, with the output voltage adjusted by tuning the input voltage and controlling the bias magnetic field. The influence of the optimal core saturation on the operation of the SOS diode is studied. An adjustable output voltage impulse of more than 200 kV amplitude with a 16 ns rise time is demonstrated on a 1 $\text{k}\Omega$ resistive load.
- 26 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 51 (10) , 2878-2884
Impact-Ionization Switching of High-Voltage Thyristors Connected in Parallel
Thyristors triggered in the impact-ionization wave mode is a promising switching method in pulsed power technology. This triggering approach enhances the current capability of standard thyristors, allowing switching a current pulse with an amplitude of 200 kA and a current rise time rate-of-change (dI/dt) of 58 kA/ $\mu$ s. Thyristor wafer area can be considered as one of the factors that are limiting the peak current amplitude and dI/dt. Switching thyristors in parallel is a possible solution to overcome these limitations. However, no evidence was found in the literature for successful parallel switching of standard thyristors in the impact-ionization wave mode. In this research, the possibility of parallel switching of two standard thyristors rated for 2.2 kV with a wafer diameter of 32 mm was investigated. A Marx generator equipped with a peaking module was used to charge the thyristor equivalent capacitance (1 nF) up to double its static breakdown voltage with a voltage rise time rate-of-change (dV/dt) of more than 1 kV/ns, as required for impact-ionization triggering. The diagnostic system includes two wideband voltage probes (VPs) with a subnanosecond time response, which allows simultaneous measurement of a voltage drop across each thyristor connected in parallel. Two stages of thyristor operation were investigated: 1) a triggering stage, without energy switching, when a dc bias voltage is applied; and 2) a current flow stage, with energy switching, when an $RLC$ discharge circuit is connected. In these experiments, thyristors change from blocking to conducting state within 400 ps, switching a current pulse with an amplitude of 11 kA and a dI/dt of 6 kA/ $\mu$ s (circuit limits). The current imbalance between the thyristors was less than 10%. To the best of the authors’ knowledge, it is the first time reported that high-voltage thyristors connected in parallel have been successfully triggered in the impact-ionization wave mode.
- 26 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 51 (10) , 2878-2884
Impact-Ionization Switching of High-Voltage Thyristors Connected in Parallel
Thyristors triggered in the impact-ionization wave mode is a promising switching method in pulsed power technology. This triggering approach enhances the current capability of standard thyristors, allowing switching a current pulse with an amplitude of 200 kA and a current rise time rate-of-change (dI/dt) of 58 kA/ $\mu$ s. Thyristor wafer area can be considered as one of the factors that are limiting the peak current amplitude and dI/dt. Switching thyristors in parallel is a possible solution to overcome these limitations. However, no evidence was found in the literature for successful parallel switching of standard thyristors in the impact-ionization wave mode. In this research, the possibility of parallel switching of two standard thyristors rated for 2.2 kV with a wafer diameter of 32 mm was investigated. A Marx generator equipped with a peaking module was used to charge the thyristor equivalent capacitance (1 nF) up to double its static breakdown voltage with a voltage rise time rate-of-change (dV/dt) of more than 1 kV/ns, as required for impact-ionization triggering. The diagnostic system includes two wideband voltage probes (VPs) with a subnanosecond time response, which allows simultaneous measurement of a voltage drop across each thyristor connected in parallel. Two stages of thyristor operation were investigated: 1) a triggering stage, without energy switching, when a dc bias voltage is applied; and 2) a current flow stage, with energy switching, when an $RLC$ discharge circuit is connected. In these experiments, thyristors change from blocking to conducting state within 400 ps, switching a current pulse with an amplitude of 11 kA and a dI/dt of 6 kA/ $\mu$ s (circuit limits). The current imbalance between the thyristors was less than 10%. To the best of the authors’ knowledge, it is the first time reported that high-voltage thyristors connected in parallel have been successfully triggered in the impact-ionization wave mode.
- 25 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 51 (10) , 2858-2865
New SOS Diode Pumping Circuit Based on an All-Solid-State Spiral Generator for High-Voltage Nanosecond Applications
Semiconductor opening switch (SOS) diodes are capable to switch currents with a density of more than 1 kA/cm 2 and withstand nanosecond pulses with an amplitude of up to 1 MV. SOS diodes, however, require a specific pumping circuit that must simultaneously provide forward and reverse pumping currents with a time of $\sim$ 500 and $\sim$ 100 ns, respectively. Such a pumping circuit with energies $>$ 1 J typically requires a gas-discharge switch or a low-efficient solid-state solution. This study proposes a novel approach to pumping SOS diodes based on a spiral generator (SG) (also known as a vector inversion generator). Due to its wave characteristics, the SG produces a bipolar current discharge that meets the time duration and current amplitude required to pump an SOS diode. Moreover, the initial pulse from the spiral typically has a relatively low current amplitude compared to the opposite polarity secondary pulse, so the SOS diode can operate at very high efficiencies. This idea has been tested using an all-solid-state SG coupled with large-area SOS diodes (1 cm 2 ). With this combination, a voltage pulse of 62 kV having a rise time of only 11 ns was obtained on an open circuit load (3 pF, 1 M $\Omega$ ). The experiments were highly repeatable, with no damage to the components despite multiple tests. There is significant scope to further improve the results, with simple alterations to the SG.
- 25 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 51 (10) , 2858-2865
New SOS Diode Pumping Circuit Based on an All-Solid-State Spiral Generator for High-Voltage Nanosecond Applications
Semiconductor opening switch (SOS) diodes are capable to switch currents with a density of more than 1 kA/cm 2 and withstand nanosecond pulses with an amplitude of up to 1 MV. SOS diodes, however, require a specific pumping circuit that must simultaneously provide forward and reverse pumping currents with a time of $\sim$ 500 and $\sim$ 100 ns, respectively. Such a pumping circuit with energies $>$ 1 J typically requires a gas-discharge switch or a low-efficient solid-state solution. This study proposes a novel approach to pumping SOS diodes based on a spiral generator (SG) (also known as a vector inversion generator). Due to its wave characteristics, the SG produces a bipolar current discharge that meets the time duration and current amplitude required to pump an SOS diode. Moreover, the initial pulse from the spiral typically has a relatively low current amplitude compared to the opposite polarity secondary pulse, so the SOS diode can operate at very high efficiencies. This idea has been tested using an all-solid-state SG coupled with large-area SOS diodes (1 cm 2 ). With this combination, a voltage pulse of 62 kV having a rise time of only 11 ns was obtained on an open circuit load (3 pF, 1 M $\Omega$ ). The experiments were highly repeatable, with no damage to the components despite multiple tests. There is significant scope to further improve the results, with simple alterations to the SG.
- 11 August 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 50 (10) , 3452-3458
A Study of a 5.2-kV/100-mm Thyristor Triggered in Impact-Ionization Mode Toward Fast High-Current Applications
Microsecond-range high-current pulses (hundreds of kA) with high$dI/dt$ (100$\textrm {kA/$\mu $s}$ ) are used to generate megagauss-range magnetic fields. Industrial applications of such technology require high average power, repeatability, and a reliable high-current pulse generator with a long lifespan. Hence, the development of a fast solid-state switch operating in the range of several hundred kA is of great interest. The switching characteristics of semiconductor devices have been substantially enhanced due to an effect of the delayed impact-ionization breakdown of the high-voltage p-n junction. This leads to the subnanosecond switching time of high-voltage semiconductor devices and an increase in their rate of current rise$dI/dt$ capability. Nevertheless, the maximum current amplitude and$dI/dt$ are limited by the area of the semiconductor device. Therefore, to increase current switching parameters, one can use a large-area structure. However, a trigger generator becomes the main challenge, in this case, due to the increased capacitance of the switch. In this article, we study the possibility of triggering large-area thyristors in impact-ionization wave mode using a Marx generator equipped with a peaking module. An experimental setup has been developed to investigate a switching process of the thyristors with a wafer diameter of$\textrm {100}~\textrm {mm}$ and a blocking voltage of$\textrm {5.2}~\textrm {kV}$ . A trigger circuit based on the Marx generator with the peaking module was developed. It can deliver pulses with$dV/dt$ of several kV/ns into a few nF capacitive loads which correspond to the equivalent thyristor capacitance. Next, the transition of the thyristor from the blocking state to the conducting state in impact-ionization mode without energy switching is presented. Finally, by adding an energy discharge circuit, the thyristor switching in impact-ionization mode is analyzed. By applying a trigger pulse with$dV/dt$ of 1.7 kV/ns to the thyristor, the voltage across it reaches 10.7 kV that leads to the following switching parameters: thyristor switching time 420 ps,$dI/dt~\sim 15~\textrm {kA/$\mu $s}$ , current amplitude$\sim 20$ kA, and current full width at half maximum (FWHM)$\sim 3~\mu \text{s}$ . To the best of our knowledge, impact-ionization switching of the standard thyristor (5.2 kV, 100 mm) was demonstrated for the first time.- 11 August 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 50 (10) , 3452-3458
A Study of a 5.2-kV/100-mm Thyristor Triggered in Impact-Ionization Mode Toward Fast High-Current Applications
Microsecond-range high-current pulses (hundreds of kA) with high$dI/dt$ (100$\textrm {kA/$\mu $s}$ ) are used to generate megagauss-range magnetic fields. Industrial applications of such technology require high average power, repeatability, and a reliable high-current pulse generator with a long lifespan. Hence, the development of a fast solid-state switch operating in the range of several hundred kA is of great interest. The switching characteristics of semiconductor devices have been substantially enhanced due to an effect of the delayed impact-ionization breakdown of the high-voltage p-n junction. This leads to the subnanosecond switching time of high-voltage semiconductor devices and an increase in their rate of current rise$dI/dt$ capability. Nevertheless, the maximum current amplitude and$dI/dt$ are limited by the area of the semiconductor device. Therefore, to increase current switching parameters, one can use a large-area structure. However, a trigger generator becomes the main challenge, in this case, due to the increased capacitance of the switch. In this article, we study the possibility of triggering large-area thyristors in impact-ionization wave mode using a Marx generator equipped with a peaking module. An experimental setup has been developed to investigate a switching process of the thyristors with a wafer diameter of$\textrm {100}~\textrm {mm}$ and a blocking voltage of$\textrm {5.2}~\textrm {kV}$ . A trigger circuit based on the Marx generator with the peaking module was developed. It can deliver pulses with$dV/dt$ of several kV/ns into a few nF capacitive loads which correspond to the equivalent thyristor capacitance. Next, the transition of the thyristor from the blocking state to the conducting state in impact-ionization mode without energy switching is presented. Finally, by adding an energy discharge circuit, the thyristor switching in impact-ionization mode is analyzed. By applying a trigger pulse with$dV/dt$ of 1.7 kV/ns to the thyristor, the voltage across it reaches 10.7 kV that leads to the following switching parameters: thyristor switching time 420 ps,$dI/dt~\sim 15~\textrm {kA/$\mu $s}$ , current amplitude$\sim 20$ kA, and current full width at half maximum (FWHM)$\sim 3~\mu \text{s}$ . To the best of our knowledge, impact-ionization switching of the standard thyristor (5.2 kV, 100 mm) was demonstrated for the first time.