Soeren Gies
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Soeren Gies has a total of 74 co-authors. Here are the top co-authors by number of shared publications:
- Ahmet Erman Tekkaya
TU Dortmund
36 shared publications - Joern Lueg-Althoff
Institute of Forming Technology and Lightweight Components, TU Dortmund University, Baroper Str. 303, D-44227 Dortmund, Germany
8 shared publications - Christian Weddeling
Institute of Forming Technology and Lightweight Construction, TU Dortmund University, Germany
7 shared publications - Sebastian Wernicke
Institute of Forming Technology and Lightweight Components, TU Dortmund University, Dortmund, Germany
7 shared publications Eckhard Beyer
5 shared publications- Marlon Hahn
TU Dortmund University
5 shared publications
Latest Publications
- Top Cited PapersOpen Access
- 31 July 2020
- Published by Springer Nature in Automotive Innovation
- Vol. 3 (3) , 195-209
Lightweight in Automotive Components by Forming Technology
Lightweight design is one of the current key drivers to reduce the energy consumption of vehicles. Design methodologies for lightweight components, strategies utilizing materials with favorable specific properties and hybrid materials are used to increase the performance of parts for automotive applications. In this paper, various forming processes to produce light parts are described. Material lightweight design is discussed, covering the manufacturing processes to produce hybrid components like fiber–metal, polymer–metal and metal–metal composites, which can be used in subsequent deep drawing or combined forming processes. Approaches to increasing the specific strength and stiffness with thermomechanical forming processes as well as the in situ control of the microstructure of such components are presented. Structure lightweight design discusses possibilities to plastically form high-strength or high-performance materials like magnesium or titanium in sheet, profile and tube forming operations. To join those materials and/or dissimilar materials, new joining by forming technologies are shown. To economically produce lightweight parts with gears or functional elements, incremental sheet-bulk metal forming is presented. As an important part property, the damage evolution during the forming operations will be discussed to enable even lighter parts through a more reliable design. New methods for predicting and tailoring the mechanical properties like strength and residual stresses will be shown. The possibilities of system lightweight design with forming technologies are presented. A combination of additive manufacturing and forming to produce highly complex parts with integrated functions will be shown. The integration of functions by a hot extrusion process for the manufacturing of shape memory alloys is presented. An in-depth understanding of the newly developed processes, methodologies and effects allows for a more accurate dimensioning of components. This facilitates a reduction in the total mass and an increasing performance of vehicle components.
- 31 July 2020
- Published by Springer Nature in Automotive Innovation
- Vol. 3 (3) , 195-209
Top Cited PapersOpen AccessLightweight in Automotive Components by Forming Technology
Lightweight design is one of the current key drivers to reduce the energy consumption of vehicles. Design methodologies for lightweight components, strategies utilizing materials with favorable specific properties and hybrid materials are used to increase the performance of parts for automotive applications. In this paper, various forming processes to produce light parts are described. Material lightweight design is discussed, covering the manufacturing processes to produce hybrid components like fiber–metal, polymer–metal and metal–metal composites, which can be used in subsequent deep drawing or combined forming processes. Approaches to increasing the specific strength and stiffness with thermomechanical forming processes as well as the in situ control of the microstructure of such components are presented. Structure lightweight design discusses possibilities to plastically form high-strength or high-performance materials like magnesium or titanium in sheet, profile and tube forming operations. To join those materials and/or dissimilar materials, new joining by forming technologies are shown. To economically produce lightweight parts with gears or functional elements, incremental sheet-bulk metal forming is presented. As an important part property, the damage evolution during the forming operations will be discussed to enable even lighter parts through a more reliable design. New methods for predicting and tailoring the mechanical properties like strength and residual stresses will be shown. The possibilities of system lightweight design with forming technologies are presented. A combination of additive manufacturing and forming to produce highly complex parts with integrated functions will be shown. The integration of functions by a hot extrusion process for the manufacturing of shape memory alloys is presented. An in-depth understanding of the newly developed processes, methodologies and effects allows for a more accurate dimensioning of components. This facilitates a reduction in the total mass and an increasing performance of vehicle components.
- 1 May 2020
- Published by Elsevier in Journal of Materials Processing Technology
- Vol. 279
Joining dissimilar thin-walled tubes by Magnetic Pulse Welding
- 1 May 2020
- Published by Elsevier in Journal of Materials Processing Technology
- Vol. 279
Joining dissimilar thin-walled tubes by Magnetic Pulse Welding
- 1 February 2020
- Published by Elsevier in Journal of Materials Processing Technology
- Vol. 276
Analytical process design for interference-fit joining of rectangular profiles
- 1 February 2020
- Published by Elsevier in Journal of Materials Processing Technology
- Vol. 276
Analytical process design for interference-fit joining of rectangular profiles
- Open Access
Properties of Components with Incrementally Formed Gears
The process class of sheet-bulk metal forming (SBMF) involves several advantages for the manufacture of functional components. Its incremental variant (iSBMF) enables a very flexible dimensioning of components. To treat the unfavorable manufacturing time of the incremental approach, this investigation is focused on an alternative process route using rotating forming tools, which decrease the process time significantly. After an analysis of the mechanical properties as well as the micro- and macroscopic surface quality, a quasi-static benchmark test was performed. Normalized by the weight of the component, gears manufactured by iSBMF and BS600 steel presented the same load capacity as gears manufactured by blanking with subsequent hardening. Here, using innovative high strength steels with a significant strain hardening behavior like high manganese steels enables for weight-reduced gears.
Open AccessProperties of Components with Incrementally Formed Gears
The process class of sheet-bulk metal forming (SBMF) involves several advantages for the manufacture of functional components. Its incremental variant (iSBMF) enables a very flexible dimensioning of components. To treat the unfavorable manufacturing time of the incremental approach, this investigation is focused on an alternative process route using rotating forming tools, which decrease the process time significantly. After an analysis of the mechanical properties as well as the micro- and macroscopic surface quality, a quasi-static benchmark test was performed. Normalized by the weight of the component, gears manufactured by iSBMF and BS600 steel presented the same load capacity as gears manufactured by blanking with subsequent hardening. Here, using innovative high strength steels with a significant strain hardening behavior like high manganese steels enables for weight-reduced gears.
- 1 April 2019
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 753, 300-316
Forming properties of additively manufactured monolithic Hastelloy X sheets
- 1 April 2019
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 753, 300-316
Forming properties of additively manufactured monolithic Hastelloy X sheets
- Open Access
Thermal Effects in Dissimilar Magnetic Pulse Welding
Magnetic pulse welding (MPW) is often categorized as a cold welding technology, whereas latest studies evidence melted and rapidly cooled regions within the joining interface. These phenomena already occur at very low impact velocities, when the heat input due to plastic deformation is comparatively low and where jetting in the kind of a distinct material flow is not initiated. As another heat source, this study investigates the cloud of particles (CoP), which is ejected as a result of the high speed impact. MPW experiments with different collision conditions are carried out in vacuum to suppress the interaction with the surrounding air for an improved process monitoring. Long time exposures and flash measurements indicate a higher temperature in the joining gap for smaller collision angles. Furthermore, the CoP becomes a finely dispersed metal vapor because of the higher degree of compression and the increased temperature. These conditions are beneficial for the surface activation of both joining partners. A numerical temperature model based on the theory of liquid state bonding is developed and considers the heating due to the CoP as well as the enthalpy of fusion and crystallization, respectively. The time offset between the heat input and the contact is identified as an important factor for a successful weld formation. Low values are beneficial to ensure high surface temperatures at the time of contact, which corresponds to the experimental results at small collision angles.
Open AccessThermal Effects in Dissimilar Magnetic Pulse Welding
Magnetic pulse welding (MPW) is often categorized as a cold welding technology, whereas latest studies evidence melted and rapidly cooled regions within the joining interface. These phenomena already occur at very low impact velocities, when the heat input due to plastic deformation is comparatively low and where jetting in the kind of a distinct material flow is not initiated. As another heat source, this study investigates the cloud of particles (CoP), which is ejected as a result of the high speed impact. MPW experiments with different collision conditions are carried out in vacuum to suppress the interaction with the surrounding air for an improved process monitoring. Long time exposures and flash measurements indicate a higher temperature in the joining gap for smaller collision angles. Furthermore, the CoP becomes a finely dispersed metal vapor because of the higher degree of compression and the increased temperature. These conditions are beneficial for the surface activation of both joining partners. A numerical temperature model based on the theory of liquid state bonding is developed and considers the heating due to the CoP as well as the enthalpy of fusion and crystallization, respectively. The time offset between the heat input and the contact is identified as an important factor for a successful weld formation. Low values are beneficial to ensure high surface temperatures at the time of contact, which corresponds to the experimental results at small collision angles.
- Open Access
- 1 February 2019
- Published by Elsevier in Materials & Design
- Vol. 163
Light enough or go lighter?
- 1 February 2019
- Published by Elsevier in Materials & Design
- Vol. 163
Open AccessLight enough or go lighter?
- Open Access
- 5 January 2019
- Published by MDPI AG in Journal of Manufacturing and Materials Processing
- Vol. 3 (1) , 2
Analysis of the Influence of Fibers on the Formability of Metal Blanks in Manufacturing Processes for Fiber Metal Laminates
In the one-step manufacturing process for fiber metal laminate parts, the so-called in situ hybridization process, the fabrics are interacting with metal blanks. During deep drawing, the liquid matrix is injected between the metal sheets through the woven fiber layers. The metal blanks can be in contact with dry or with infiltrated fibers. The formability of the blanks is influenced by the variation of the starting time of injection. The reason for that is that, due to high contact forces, the fibers are able to deform the metal surface locally, so that movement and the strain of the blanks is inhibited. To investigate the influence of different fibers on the formability of metals, Nakazima tests are performed. In these tests, two metal blanks are formed with an interlayer of fibers. The results are compared with the formability of two blanks without any interlayer. It is shown that in with fibers between sheets, the formability decreases compared to the formability of two metal blanks without interlayers. Based on a simplified numerical model for different types of fibers, the interactions of the fibers with the metal blank are analyzed. It could be shown that the friction due to contact has more influence than the friction due to the form fit caused by the imprints.
- 5 January 2019
- Published by MDPI AG in Journal of Manufacturing and Materials Processing
- Vol. 3 (1) , 2
Open AccessAnalysis of the Influence of Fibers on the Formability of Metal Blanks in Manufacturing Processes for Fiber Metal Laminates
In the one-step manufacturing process for fiber metal laminate parts, the so-called in situ hybridization process, the fabrics are interacting with metal blanks. During deep drawing, the liquid matrix is injected between the metal sheets through the woven fiber layers. The metal blanks can be in contact with dry or with infiltrated fibers. The formability of the blanks is influenced by the variation of the starting time of injection. The reason for that is that, due to high contact forces, the fibers are able to deform the metal surface locally, so that movement and the strain of the blanks is inhibited. To investigate the influence of different fibers on the formability of metals, Nakazima tests are performed. In these tests, two metal blanks are formed with an interlayer of fibers. The results are compared with the formability of two blanks without any interlayer. It is shown that in with fibers between sheets, the formability decreases compared to the formability of two metal blanks without interlayers. Based on a simplified numerical model for different types of fibers, the interactions of the fibers with the metal blank are analyzed. It could be shown that the friction due to contact has more influence than the friction due to the form fit caused by the imprints.
- 1 December 2018
- Published by Elsevier in Journal of Materials Processing Technology
- Vol. 262, 189-203
Influence of the flyer kinetics on magnetic pulse welding of tubes
- 1 December 2018
- Published by Elsevier in Journal of Materials Processing Technology
- Vol. 262, 189-203
Influence of the flyer kinetics on magnetic pulse welding of tubes
- 24 April 2018
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 767, 405-412
Joining by Die-Less Hydroforming of Profiles with Oval Cross Section
Joining by die-less hydroforming is used to produce overlap joints by means of hydraulic expansion. Due to a difference in the elastic recovery of the two joining partners an interference pressure p remains at their contact area. Due to the possibility to produce multi-material joints without relying on heat, the process has great potential for joining parts in lightweight applications. Therefore, the process limits were extended so that profiles with non-rotationally symmetric cross-sections can be joined. For this purpose a new tool for profiles with oval cross-section was developed. The inner and the outer joining partner ware made of aluminum 6060 and aluminum 6082 respectively. The influence of the overlap length and different wall thicknesses of the outer joining partner were investigated by numerical simulations and validated by experiments. An upper limit in interference pressure was observed which was also found previously for profiles with circular cross sections. The fluid pressure limit is compared with the analytically calculated value for a configuration with circular tubes under equivalent conditions. The analytical model underestimated the pressure limit. In contrast to circular tubes, the strain distribution of profiles with oval cross sectional shapes is not uniform, which results in superposed bending stresses. Also a difference in stiffness of the inner and outer joining partner leads to a pressure depended contact area which is assumed constant in the analytical model.
- 24 April 2018
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 767, 405-412
Joining by Die-Less Hydroforming of Profiles with Oval Cross Section
Joining by die-less hydroforming is used to produce overlap joints by means of hydraulic expansion. Due to a difference in the elastic recovery of the two joining partners an interference pressure p remains at their contact area. Due to the possibility to produce multi-material joints without relying on heat, the process has great potential for joining parts in lightweight applications. Therefore, the process limits were extended so that profiles with non-rotationally symmetric cross-sections can be joined. For this purpose a new tool for profiles with oval cross-section was developed. The inner and the outer joining partner ware made of aluminum 6060 and aluminum 6082 respectively. The influence of the overlap length and different wall thicknesses of the outer joining partner were investigated by numerical simulations and validated by experiments. An upper limit in interference pressure was observed which was also found previously for profiles with circular cross sections. The fluid pressure limit is compared with the analytically calculated value for a configuration with circular tubes under equivalent conditions. The analytical model underestimated the pressure limit. In contrast to circular tubes, the strain distribution of profiles with oval cross sectional shapes is not uniform, which results in superposed bending stresses. Also a difference in stiffness of the inner and outer joining partner leads to a pressure depended contact area which is assumed constant in the analytical model.