Ahmet Turan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Ahmet Turan has a total of 62 co-authors. Here are the top co-authors by number of shared publications:
- Mehmet Bugdayci
Yalova University
8 shared publications Onuralp Yucel
Istanbul Technical University
8 shared publications- Onuralp Yücel
Istanbul Technical University
7 shared publications - Umay Cinarli Yavas
Materials Science and Nanotechnology Engineering Department, Faculty of Engineering, Yeditepe University, Ataşehir, Istanbul 34755, Turkey
5 shared publications Murat Alkan
Istanbul Technical University, Faculty of Chemistry & Metallurgy, Metallurgical and Materials Eng. Dep., stanbul, Turkey
4 shared publicationsOnuralp Yücel
Metallurgical and Materials Engineering Department, Faculty of Chemical and Metallurgical Engineering, Istanbul Technical University, Maslak, Turkey
4 shared publications
Latest Publications
- Open Access
- 28 March 2026
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 11 (13) , 20763-20776
Solution Combustion Synthesis and Characterization of (CoCrFeMnNi) 3 O 4 High-Entropy Oxide Using Different Fuels
High-entropy oxides (HEOs) have recently attracted significant interest due to their tunable crystal structures, compositional versatility, and promising functional properties in energy storage, catalysis, and magnetic applications. Among various synthesis routes, solution combustion synthesis (SCS) offers a rapid and energy-efficient pathway for producing phase-pure HEO powders with controlled morphology. In this study, (CoCrFeMnNi)3O4 high-entropy oxide was synthesized via SCS using three different fuels, followed by postcombustion heat treatments at 800, 900, and 1000 °C for 1 h. The calcination temperatures were selected based on thermogravimetric analysis (TGA) and literature data. Phase formation, microstructural evolution, and elemental distribution were investigated by X-ray diffraction (XRD) and scanning electron microscopy coupled with energy-dispersive spectroscopy (SEM-EDS), while specific surface area and porosity characteristics of selected samples were evaluated by Brunauer–Emmett–Teller (BET) analysis and its corresponding Barrett–Joyner–Halenda (BJH) method. The results revealed that the choice of fuel significantly influenced the combustion characteristics, phase purity, and particle morphology, while the calcination temperature played a key role in grain growth and densification. Glycine at a stoichiometric ratio (Φe = 1) and calcination at 900 °C yielded the most favorable results, producing sharp spinel peaks consistent with the space group and elemental distributions closest to equimolar. TGA confirmed high thermal stability with <3% weight loss up to 1000 °C, while the citric acid route exhibited ∼25% mass loss due to residual organics. Postcalcination SEM analyses showed homogeneous microstructures with well-defined grains, particularly in glycine-derived samples, whereas excess fuel or unsuitable stoichiometry led to porous or amorphous products. BET/BJH analyses of glycine-derived samples prepared at the 1.0× fuel stoichiometry further confirmed the temperature-dependent textural evolution, showing a progressive reduction in specific surface area and porosity with increasing calcination temperature, in agreement with SEM-observed densification. This work provides a systematic comparison of fuel-dependent SCS synthesis for (CoCrFeMnNi)3O4 and establishes a synthesis parameter space for obtaining single-phase spinel oxides with controlled microstructures at relatively low processing temperatures.- 28 March 2026
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 11 (13) , 20763-20776
Open AccessSolution Combustion Synthesis and Characterization of (CoCrFeMnNi) 3 O 4 High-Entropy Oxide Using Different Fuels
High-entropy oxides (HEOs) have recently attracted significant interest due to their tunable crystal structures, compositional versatility, and promising functional properties in energy storage, catalysis, and magnetic applications. Among various synthesis routes, solution combustion synthesis (SCS) offers a rapid and energy-efficient pathway for producing phase-pure HEO powders with controlled morphology. In this study, (CoCrFeMnNi)3O4 high-entropy oxide was synthesized via SCS using three different fuels, followed by postcombustion heat treatments at 800, 900, and 1000 °C for 1 h. The calcination temperatures were selected based on thermogravimetric analysis (TGA) and literature data. Phase formation, microstructural evolution, and elemental distribution were investigated by X-ray diffraction (XRD) and scanning electron microscopy coupled with energy-dispersive spectroscopy (SEM-EDS), while specific surface area and porosity characteristics of selected samples were evaluated by Brunauer–Emmett–Teller (BET) analysis and its corresponding Barrett–Joyner–Halenda (BJH) method. The results revealed that the choice of fuel significantly influenced the combustion characteristics, phase purity, and particle morphology, while the calcination temperature played a key role in grain growth and densification. Glycine at a stoichiometric ratio (Φe = 1) and calcination at 900 °C yielded the most favorable results, producing sharp spinel peaks consistent with the space group and elemental distributions closest to equimolar. TGA confirmed high thermal stability with <3% weight loss up to 1000 °C, while the citric acid route exhibited ∼25% mass loss due to residual organics. Postcalcination SEM analyses showed homogeneous microstructures with well-defined grains, particularly in glycine-derived samples, whereas excess fuel or unsuitable stoichiometry led to porous or amorphous products. BET/BJH analyses of glycine-derived samples prepared at the 1.0× fuel stoichiometry further confirmed the temperature-dependent textural evolution, showing a progressive reduction in specific surface area and porosity with increasing calcination temperature, in agreement with SEM-observed densification. This work provides a systematic comparison of fuel-dependent SCS synthesis for (CoCrFeMnNi)3O4 and establishes a synthesis parameter space for obtaining single-phase spinel oxides with controlled microstructures at relatively low processing temperatures. - 11 November 2025
- Published by Springer Nature in Mining, Metallurgy & Exploration
- Vol. 42 (6) , 4061-4084
Alumina Extraction from Diasporic Bauxite via Sodium Carbonate-Assisted Roasting and Water Leaching
- 11 November 2025
- Published by Springer Nature in Mining, Metallurgy & Exploration
- Vol. 42 (6) , 4061-4084
Alumina Extraction from Diasporic Bauxite via Sodium Carbonate-Assisted Roasting and Water Leaching
- Open Access
- 25 September 2025
- Published by Editorial CSIC in Revista de Metalurgia
- Vol. 60 (3) , e266
Gold extraction from oxide gold ores through glycine leaching
The use of glycine, a non-toxic and simple amino acid, has gained attention for gold extraction because of its selective dissolution of precious metals. This study explores gold extraction from oxide gold ore using non-analytical grade glycine at concentrations of 1-3 M and reaction times ranging from 4 to 60 hours. The pH was maintained at 11-12, with the reactor temperature set at 60 °C, a stirring speed of 350 rpm, and an air flow rate of 1 L·min-1. The ore's particle size averaged 70.7 μm. The highest gold extraction (81.41%) occurred at 3 M glycine after 48 hours. Silver extraction was moderate, reaching 44.50%, while iron solubility was low at 7.71%. The results show that increased reaction time and glycine concentration enhance gold dissolution from oxide ore. This glycine-based process offers a more environmentally friendly and sustainable approach for selective extraction of gold and silver from oxide ores or oxidized waste containing precious metals.
- 25 September 2025
- Published by Editorial CSIC in Revista de Metalurgia
- Vol. 60 (3) , e266
Open AccessGold extraction from oxide gold ores through glycine leaching
The use of glycine, a non-toxic and simple amino acid, has gained attention for gold extraction because of its selective dissolution of precious metals. This study explores gold extraction from oxide gold ore using non-analytical grade glycine at concentrations of 1-3 M and reaction times ranging from 4 to 60 hours. The pH was maintained at 11-12, with the reactor temperature set at 60 °C, a stirring speed of 350 rpm, and an air flow rate of 1 L·min-1. The ore's particle size averaged 70.7 μm. The highest gold extraction (81.41%) occurred at 3 M glycine after 48 hours. Silver extraction was moderate, reaching 44.50%, while iron solubility was low at 7.71%. The results show that increased reaction time and glycine concentration enhance gold dissolution from oxide ore. This glycine-based process offers a more environmentally friendly and sustainable approach for selective extraction of gold and silver from oxide ores or oxidized waste containing precious metals.
- Open Access
- 11 July 2024
- Published by MDPI AG in Journal of Composites Science
- Vol. 8 (7) , 267
High-Temperature Synthesis of Superconducting MgB2 Materials in a Centrifuge
There is a wide variety of superconducting materials, but only a few of them are suitable for practical industrial use, and one of the most promising superconductors is MgB2. Its main advantages are a critical temperature close to 40 K, which allows for operation in a cryogenic environment, low cost of precursors, and the ease of manufacture. In this paper, we attempted to obtain superconducting materials based on magnesium diboride in a new way by using a high-temperature centrifuge and then investigated how centrifugal acceleration could affect the superconducting characteristics of the materials in a greater way during combustion synthesis. As a brief result of this research, it was found that the value of centrifugal acceleration affected the critical current density (Jc = 1.4 A/cm2) of the MgB2 composites, although it did not considerably impact the critical transition temperature of the MgB2 materials (remained at around 37.5–38 K).
- 11 July 2024
- Published by MDPI AG in Journal of Composites Science
- Vol. 8 (7) , 267
Open AccessHigh-Temperature Synthesis of Superconducting MgB2 Materials in a Centrifuge
There is a wide variety of superconducting materials, but only a few of them are suitable for practical industrial use, and one of the most promising superconductors is MgB2. Its main advantages are a critical temperature close to 40 K, which allows for operation in a cryogenic environment, low cost of precursors, and the ease of manufacture. In this paper, we attempted to obtain superconducting materials based on magnesium diboride in a new way by using a high-temperature centrifuge and then investigated how centrifugal acceleration could affect the superconducting characteristics of the materials in a greater way during combustion synthesis. As a brief result of this research, it was found that the value of centrifugal acceleration affected the critical current density (Jc = 1.4 A/cm2) of the MgB2 composites, although it did not considerably impact the critical transition temperature of the MgB2 materials (remained at around 37.5–38 K).
- Open Access
- 1 September 2023
- Published by Elsevier in South African Journal of Chemical Engineering
- Vol. 46, 343-350
Investigation of thermal properties of carbon containing composites obtained by solid-state combustion
- 1 September 2023
- Published by Elsevier in South African Journal of Chemical Engineering
- Vol. 46, 343-350
Open AccessInvestigation of thermal properties of carbon containing composites obtained by solid-state combustion
- Open Access
- 1 January 2023
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2803 (1)
Study of physico-chemical properties of refractory materials synthesized from metallurgical waste
The aim of the research was to investigate the utility of components of metallurgical wastes in the production of high temperature refractory bricks based on rich and poor chromium spinel powder (HSP) waste produced by self-propagating high-temperature synthesis method. The series of experiments on the obtaining of carbon containing refractories based on the waste of rich and poor chrome spinel powder were conducted in a muffle furnace. The effect of the adding of rich and poor chromium waste on refractories’ mechanical and thermal properties were detailly studied. Thermodynamic calculations and thermochemical modeling were performed between the components of metallurgical waste using the HSC Chemistry software. The diagram and graph were constructed that demonstrate the possibility of forming high quality refractory materials under experimental conditions using calculation modules. The compressive strength value of obtained sample was at competitive level in accordance with series of mechanical tests.
- 1 January 2023
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2803 (1)
Open AccessStudy of physico-chemical properties of refractory materials synthesized from metallurgical waste
The aim of the research was to investigate the utility of components of metallurgical wastes in the production of high temperature refractory bricks based on rich and poor chromium spinel powder (HSP) waste produced by self-propagating high-temperature synthesis method. The series of experiments on the obtaining of carbon containing refractories based on the waste of rich and poor chrome spinel powder were conducted in a muffle furnace. The effect of the adding of rich and poor chromium waste on refractories’ mechanical and thermal properties were detailly studied. Thermodynamic calculations and thermochemical modeling were performed between the components of metallurgical waste using the HSC Chemistry software. The diagram and graph were constructed that demonstrate the possibility of forming high quality refractory materials under experimental conditions using calculation modules. The compressive strength value of obtained sample was at competitive level in accordance with series of mechanical tests.
- 25 October 2022
- Published by Taylor & Francis in Separation Science and Technology
- Vol. 58 (3) , 573-585
Solution combustion synthesis derived Li4SiO4 for post-combustion carbon capture
Lithium-based sorbents are considered as promising candidates for post-combustion carbon capture because of their superior stability compared to CaO. In the present study, Li4SiO4 powders were synthesized by Solution Combustion Synthesis (SCS) technique using LiNO3 as lithium source, TEOS as silicon source and citric acid as the fuel. CO2 sorption tests were carried out for the synthesized samples and, powder prepared at 650°C during 4 h, which has 17 µm of particle size, 5.2 m2 g−1 of specific surface area, 85.2% Li4SiO4 phase purity with 97 nm of crystallite size showed a sorption performance as 29.5 wt% CO2 uptake value, in thermobalance test under 92 vol% CO2 (N2 balance) gas concentration at 600°C. The sample had a CO2 uptake value of 21.4 wt% under 20 vol% CO2 concentration which was chosen to simulate industrial off-gas conditions. Also, the same sample showed a good cyclic durability during the sorption/desorption tests. The sample maintained its cyclic CO2 uptake capability range between 21 and 24 wt% for 15 cycles.
- 25 October 2022
- Published by Taylor & Francis in Separation Science and Technology
- Vol. 58 (3) , 573-585
Solution combustion synthesis derived Li4SiO4 for post-combustion carbon capture
Lithium-based sorbents are considered as promising candidates for post-combustion carbon capture because of their superior stability compared to CaO. In the present study, Li4SiO4 powders were synthesized by Solution Combustion Synthesis (SCS) technique using LiNO3 as lithium source, TEOS as silicon source and citric acid as the fuel. CO2 sorption tests were carried out for the synthesized samples and, powder prepared at 650°C during 4 h, which has 17 µm of particle size, 5.2 m2 g−1 of specific surface area, 85.2% Li4SiO4 phase purity with 97 nm of crystallite size showed a sorption performance as 29.5 wt% CO2 uptake value, in thermobalance test under 92 vol% CO2 (N2 balance) gas concentration at 600°C. The sample had a CO2 uptake value of 21.4 wt% under 20 vol% CO2 concentration which was chosen to simulate industrial off-gas conditions. Also, the same sample showed a good cyclic durability during the sorption/desorption tests. The sample maintained its cyclic CO2 uptake capability range between 21 and 24 wt% for 15 cycles.
- Open Access
- 13 September 2022
- Published by MDPI AG in Sustainability
- Vol. 14 (18) , 11439
Production of Refractory Bricks through Combustion Synthesis from Metallurgical Wastes and the Thermo-Physical Properties of the Products
Industrial symbiosis is one of the key approaches to meet sustainable and low carbon production targets. Thus, through circular approaches, it is possible to reduce the use of natural crude materials and make production processes waste-free in the metallurgical industry. The purpose of this study was to study the possibility of using various metallurgical waste and low-grade semi-finished products, which do not have a direct application area, in the production of heat-resistant carbon-containing refractory bricks through the combustion synthesis (CS) method. In the experiments, used metallurgical wastes were wet filter cake (FC), sludge (S), and refractory magnesite scrap (MS) while semi-products were rich and poor dust of chrome spinel (Cr-S). Simultaneously with the experiments, thermochemical simulation studies were carried out using the HSC Chemistry 6.12 to predict the thermodynamic properties of the reactions and possible reaction products. Thermal conductivity coefficients were determined in products in terms of thermal properties of composite samples, they were between 0.511 and 1.020 Wm/K. The phase compositions of the produced samples were determined via XRD technique. The TG-DTA technique was used to characterize thermal behavior of products. In addition, mechanical properties were determined by compression strength test. As a result of experiments, it was observed that Cr-S-rich-based samples showed a promising result in comparison to others: increasing amount of useful carbide phases were formed and demonstrated a high value of mechanical properties. Compression strength was increased from 2.7 MPa (sample №4) to 15.8 MPa (sample №1) with increasing chromite-containing phases in the green samples.
- 13 September 2022
- Published by MDPI AG in Sustainability
- Vol. 14 (18) , 11439
Open AccessProduction of Refractory Bricks through Combustion Synthesis from Metallurgical Wastes and the Thermo-Physical Properties of the Products
Industrial symbiosis is one of the key approaches to meet sustainable and low carbon production targets. Thus, through circular approaches, it is possible to reduce the use of natural crude materials and make production processes waste-free in the metallurgical industry. The purpose of this study was to study the possibility of using various metallurgical waste and low-grade semi-finished products, which do not have a direct application area, in the production of heat-resistant carbon-containing refractory bricks through the combustion synthesis (CS) method. In the experiments, used metallurgical wastes were wet filter cake (FC), sludge (S), and refractory magnesite scrap (MS) while semi-products were rich and poor dust of chrome spinel (Cr-S). Simultaneously with the experiments, thermochemical simulation studies were carried out using the HSC Chemistry 6.12 to predict the thermodynamic properties of the reactions and possible reaction products. Thermal conductivity coefficients were determined in products in terms of thermal properties of composite samples, they were between 0.511 and 1.020 Wm/K. The phase compositions of the produced samples were determined via XRD technique. The TG-DTA technique was used to characterize thermal behavior of products. In addition, mechanical properties were determined by compression strength test. As a result of experiments, it was observed that Cr-S-rich-based samples showed a promising result in comparison to others: increasing amount of useful carbide phases were formed and demonstrated a high value of mechanical properties. Compression strength was increased from 2.7 MPa (sample №4) to 15.8 MPa (sample №1) with increasing chromite-containing phases in the green samples.
- 26 October 2020
- Published by Springer Nature in Mining, Metallurgy & Exploration
- Vol. 38 (1) , 257-267
Investigation of Alumina-Based Ceramic Production from Aluminum Black Dross
- 26 October 2020
- Published by Springer Nature in Mining, Metallurgy & Exploration
- Vol. 38 (1) , 257-267
Investigation of Alumina-Based Ceramic Production from Aluminum Black Dross