Cuiting Sun
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Cuiting Sun has a total of 85 co-authors. Here are the top co-authors by number of shared publications:
- Tao Geng
Harbin Engineering University
18 shared publications - Libo Yuan
Guilin University of Electronic Technology
15 shared publications - Weimin Sun
Key Lab of In-fiber Integrated Optics, Ministry Education of China, Harbin Engineering University, Harbin 150001, China
12 shared publications - Shuo Zhang
Harbin Engineering University
9 shared publications Xiren Jin
Key Laboratory of In-Fiber Integrated Optics, Ministry Education of China, Harbin Engineering University, Harbin, China
9 shared publicationsChupeng Lu
Key Laboratory of In-Fiber Integrated Optics, Ministry Education of China, Harbin Engineering University, Harbin, China
7 shared publications
Latest Publications
- 23 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 23 (20) , 24264-24270
A Fiber-Based Torsion Sensor With Tunable Sensitivity
In this paper, a torsion sensor with tunable sensitivity based on long period fiber grating (LPFG) written in polarization maintaining fiber (pMf) is proposed. The LPFG is fabricated by polishing periodic complementary grooves on the principal axis of stress of PMf. By modulating with the CO 2 laser, the structural stability of the principal axis of stress is destroyed, which reduce the birefringence effect of the PMF itself. Meanwhile, the elliptical birefringence effect during the torsion is enhanced. Therefore, the torsion sensitivity of the PMF sensor is improved. The experimental results show that the torsion sensitivity can reach 0.81 nm/(rad/m) in the range of -5.70 nm/rad to 5.70 nm/rad in the slow axis direction. The torsion sensitivity is 0.43 nm/(rad/m) in the large measurement range from -11.40 rad/m to 11.40 rad/m in the fast axis direction. Depending on the polarization condition of the incident light, the designed sensor can choose different sensitivities and measurement ranges.
- 23 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 23 (20) , 24264-24270
A Fiber-Based Torsion Sensor With Tunable Sensitivity
In this paper, a torsion sensor with tunable sensitivity based on long period fiber grating (LPFG) written in polarization maintaining fiber (pMf) is proposed. The LPFG is fabricated by polishing periodic complementary grooves on the principal axis of stress of PMf. By modulating with the CO 2 laser, the structural stability of the principal axis of stress is destroyed, which reduce the birefringence effect of the PMF itself. Meanwhile, the elliptical birefringence effect during the torsion is enhanced. Therefore, the torsion sensitivity of the PMF sensor is improved. The experimental results show that the torsion sensitivity can reach 0.81 nm/(rad/m) in the range of -5.70 nm/rad to 5.70 nm/rad in the slow axis direction. The torsion sensitivity is 0.43 nm/(rad/m) in the large measurement range from -11.40 rad/m to 11.40 rad/m in the fast axis direction. Depending on the polarization condition of the incident light, the designed sensor can choose different sensitivities and measurement ranges.
- 9 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 23 (8) , 8410-8415
A Highly Sensitive Curvature Sensor Based on Omega-Shaped Long-Period Fiber Grating
A compact Omega shaped long-period fiber grating (OS-LPFG) for vector bending measurement is proposed and investigated in this paper. This sensor is fabricated by periodically splicing single-mode fiber (SMF) and multi-mode fiber (MMF) into Omega shape to get the purpose of sensitivity enhancing. The proposed OS-LPFG can distinguish the bending direction and achieves the curvature sensitivities in X, Y, -X directions are 12.03 nm/m -1 , –69.95 nm/m -1 and –19.84 nm/m -1 at the range of 0 m -1 to 1.5 m -1 . Meanwhile, the sensor has a small temperature crosstalk of 0.0011 m -1 /°C at the temperature range of 20 °C to 110 °C. In addition, the sensor features a compact structure with the length of 1.5 mm due to the strong refractive index modulation induced by fabricating method, which proposes a feasible idea for compact fiber curvature sensor design.
- 9 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 23 (8) , 8410-8415
A Highly Sensitive Curvature Sensor Based on Omega-Shaped Long-Period Fiber Grating
A compact Omega shaped long-period fiber grating (OS-LPFG) for vector bending measurement is proposed and investigated in this paper. This sensor is fabricated by periodically splicing single-mode fiber (SMF) and multi-mode fiber (MMF) into Omega shape to get the purpose of sensitivity enhancing. The proposed OS-LPFG can distinguish the bending direction and achieves the curvature sensitivities in X, Y, -X directions are 12.03 nm/m -1 , –69.95 nm/m -1 and –19.84 nm/m -1 at the range of 0 m -1 to 1.5 m -1 . Meanwhile, the sensor has a small temperature crosstalk of 0.0011 m -1 /°C at the temperature range of 20 °C to 110 °C. In addition, the sensor features a compact structure with the length of 1.5 mm due to the strong refractive index modulation induced by fabricating method, which proposes a feasible idea for compact fiber curvature sensor design.
- 26 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 34 (16) , 866-869
A Sensor With High Strain Sensitivity Based on Four-Sided Modulated LPFG
In this letter, a novel strain sensor based on four-sided modulated long period fiber grating (FM-LPFG) is introduced and demonstrated. Due to the asymmetric refractive index modulation of the CO 2 laser, the cladding radius is reduced and the core deviation effect is strengthened. In addition, by simulating the equivalent strain during tension, the strain sensitive area of FM-LPFG is proposed. The measurement results indicate that the strain sensitivity of FM-LPFG is 127.5 pm/$\mu \varepsilon $ ($0~\sim ~125~\mu \varepsilon$ ) and 17.7 pm/$\mu \varepsilon $ ($125~\sim ~575~\mu \varepsilon$ ). The proposed FM-LPFG can be realistically applied in precision measurement.- 26 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 34 (16) , 866-869
A Sensor With High Strain Sensitivity Based on Four-Sided Modulated LPFG
In this letter, a novel strain sensor based on four-sided modulated long period fiber grating (FM-LPFG) is introduced and demonstrated. Due to the asymmetric refractive index modulation of the CO 2 laser, the cladding radius is reduced and the core deviation effect is strengthened. In addition, by simulating the equivalent strain during tension, the strain sensitive area of FM-LPFG is proposed. The measurement results indicate that the strain sensitivity of FM-LPFG is 127.5 pm/$\mu \varepsilon $ ($0~\sim ~125~\mu \varepsilon$ ) and 17.7 pm/$\mu \varepsilon $ ($125~\sim ~575~\mu \varepsilon$ ). The proposed FM-LPFG can be realistically applied in precision measurement.- 5 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 22 (12) , 11756-11762
An Improved Strain Sensor Based on Long-Period Fiber Grating With a Local Ellipse-Core Structure
In this paper, we proposed a novel long-period fiber grating strain sensor based on local ellipse-core fiber (LEC-LPFG). The LEC-LPFG was fabricated by laser polishing and local heating methods, which could efficiently transform a single-mode fiber (SMF) into a periodic ellipse-core fiber. The effects associated with the fiber elliptical core shape were shown to significantly influence the strain sensitivity of the LEC-LPFG. Further, it was demonstrated that the LEC-LPFG has a high strain sensitivity of −20.2 pm/ $\mu \varepsilon $ and a temperature sensitivity of 68.6 pm/°C. Our work provides a new technology for straightforward, low-cost, and large-scale productions of premium fiber optical strain sensors which are desirable in many practical applications.
- 5 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 22 (12) , 11756-11762
An Improved Strain Sensor Based on Long-Period Fiber Grating With a Local Ellipse-Core Structure
In this paper, we proposed a novel long-period fiber grating strain sensor based on local ellipse-core fiber (LEC-LPFG). The LEC-LPFG was fabricated by laser polishing and local heating methods, which could efficiently transform a single-mode fiber (SMF) into a periodic ellipse-core fiber. The effects associated with the fiber elliptical core shape were shown to significantly influence the strain sensitivity of the LEC-LPFG. Further, it was demonstrated that the LEC-LPFG has a high strain sensitivity of −20.2 pm/ $\mu \varepsilon $ and a temperature sensitivity of 68.6 pm/°C. Our work provides a new technology for straightforward, low-cost, and large-scale productions of premium fiber optical strain sensors which are desirable in many practical applications.
- 3 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 34 (1) , 11-14
An All Fiber Mach-Zehnder Interferometer Based on Tapering Core-Offset Joint for Strain Sensing
A Mach-Zehnder interferometer, composed of two core-offset tapered joints (COTJ-MZI), is proposed and experimentally verified for high sensitivity strain sensing. The COTJ-MZI is handily fabricated by core-offset fusion splicing and tapering based on all single-mode fiber (SMF). The fiber cores form stepped cores within the COTJs. The transmission spectra with different core-offset values and interference lengths are obtained and theoretically analyzed. Benefitting from the stepped cores in the COTJ structure, the mode coupling points are able to be modulated easily by the applied strain. A strain sensitivity of −108.0 pm/$\mu \varepsilon $ (0-$400~\mu \varepsilon$ ) and −47.6 pm/$\mu \varepsilon $ (400-1200$\mu \varepsilon$ ) is achieved. In addition, the temperature response is also characterized as low as 23.3 pm/°C. With the advantages of low cost and high sensitivity, the COTJ-MZI sensor is competitive candidates in the field of strain measurement.- 3 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 34 (1) , 11-14
An All Fiber Mach-Zehnder Interferometer Based on Tapering Core-Offset Joint for Strain Sensing
A Mach-Zehnder interferometer, composed of two core-offset tapered joints (COTJ-MZI), is proposed and experimentally verified for high sensitivity strain sensing. The COTJ-MZI is handily fabricated by core-offset fusion splicing and tapering based on all single-mode fiber (SMF). The fiber cores form stepped cores within the COTJs. The transmission spectra with different core-offset values and interference lengths are obtained and theoretically analyzed. Benefitting from the stepped cores in the COTJ structure, the mode coupling points are able to be modulated easily by the applied strain. A strain sensitivity of −108.0 pm/$\mu \varepsilon $ (0-$400~\mu \varepsilon$ ) and −47.6 pm/$\mu \varepsilon $ (400-1200$\mu \varepsilon$ ) is achieved. In addition, the temperature response is also characterized as low as 23.3 pm/°C. With the advantages of low cost and high sensitivity, the COTJ-MZI sensor is competitive candidates in the field of strain measurement.- 15 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 21 (21) , 24129-24133
A Vector Bending Sensor Based on a Core-Offset Long Period Fiber Grating Induced by an Arc-Discharge
We proposed and experimentally demonstrated a vector bending sensor based on a core-offset long period fiber grating (CO-LPFG). The CO-LPFG is configured by CO 2 laser polishing on three mutually orthogonal planes of a single mode fiber (SMF) to different depths and then heating it by the electrical arc-discharge of a fusion splicer. The asymmetrical cladding structure leads to an uneven density distribution of the fiber in the molten state. Under the effects of releasing the residual stress and fiber surface tension, the fiber core deviates toward the polished deeper directions to form a core-offset structure in two dimensions. The experimental results demonstrate that the bending sensitivities of CO-LPFG reach 37.06 nm/m −1 −5.85 nm/m −1 -14.59 nm/m −1 and −12.45 nm/m −1 for four bending directions within the range of 1.12-2.10 m −1 The temperature sensitivity of CO-LPFG is 57.90 pm/°C in the range of 40-160°C.
- 15 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 21 (21) , 24129-24133
A Vector Bending Sensor Based on a Core-Offset Long Period Fiber Grating Induced by an Arc-Discharge
We proposed and experimentally demonstrated a vector bending sensor based on a core-offset long period fiber grating (CO-LPFG). The CO-LPFG is configured by CO 2 laser polishing on three mutually orthogonal planes of a single mode fiber (SMF) to different depths and then heating it by the electrical arc-discharge of a fusion splicer. The asymmetrical cladding structure leads to an uneven density distribution of the fiber in the molten state. Under the effects of releasing the residual stress and fiber surface tension, the fiber core deviates toward the polished deeper directions to form a core-offset structure in two dimensions. The experimental results demonstrate that the bending sensitivities of CO-LPFG reach 37.06 nm/m −1 −5.85 nm/m −1 -14.59 nm/m −1 and −12.45 nm/m −1 for four bending directions within the range of 1.12-2.10 m −1 The temperature sensitivity of CO-LPFG is 57.90 pm/°C in the range of 40-160°C.
- Open Access
- 6 July 2021
- Published by Optica Publishing Group in Optics Express
- Vol. 29 (15) , 22813-22822
Highly sensitive vector bending sensor based on an embedded multimode D-shaped LPFG
In this letter, a highly sensitive bending sensor based on an embedded multimode D-shaped long period fiber grating (EMD-LPFG) is proposed. The novel sensor is applied to carry out vector bending measurement. The proposed LPFG is fabricated by polishing on the prepared structure which is formed by periodically splicing between single mode fiber (SMF) and multimode fiber (MMF). Since the cross section of the embedded MMF is D-shaped, we named it EMD-LPFG. Due to the asymmetric modulation of the refractive index on the fiber by the CO2 laser, the sensor has the ability to distinguish the bending directions, and the MMFs provide higher bending response. The experimental transmission spectrum can match the simulation results well. The experimental results show that the average bending sensitivities in three orthogonal directions are 70.21 nm/m−1 (0°), 9.75 nm/m−1 (90°), −12.04 nm/m−1 (180°) and 9.98 nm/m−1 (270°), respectively. Meanwhile, the temperature sensitivity is 30 pm/°C in the range of 25 °C to 75 °C. According to the ultra-compact structure with the total length of 2.5 mm, high bending sensitivity and ability to distinguish the bending direction, the novel sensor has potential in bending measurement.
- 6 July 2021
- Published by Optica Publishing Group in Optics Express
- Vol. 29 (15) , 22813-22822
Open AccessHighly sensitive vector bending sensor based on an embedded multimode D-shaped LPFG
In this letter, a highly sensitive bending sensor based on an embedded multimode D-shaped long period fiber grating (EMD-LPFG) is proposed. The novel sensor is applied to carry out vector bending measurement. The proposed LPFG is fabricated by polishing on the prepared structure which is formed by periodically splicing between single mode fiber (SMF) and multimode fiber (MMF). Since the cross section of the embedded MMF is D-shaped, we named it EMD-LPFG. Due to the asymmetric modulation of the refractive index on the fiber by the CO2 laser, the sensor has the ability to distinguish the bending directions, and the MMFs provide higher bending response. The experimental transmission spectrum can match the simulation results well. The experimental results show that the average bending sensitivities in three orthogonal directions are 70.21 nm/m−1 (0°), 9.75 nm/m−1 (90°), −12.04 nm/m−1 (180°) and 9.98 nm/m−1 (270°), respectively. Meanwhile, the temperature sensitivity is 30 pm/°C in the range of 25 °C to 75 °C. According to the ultra-compact structure with the total length of 2.5 mm, high bending sensitivity and ability to distinguish the bending direction, the novel sensor has potential in bending measurement.
- 9 December 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 21 (5) , 6217-6223
High Torsion Sensitivity Sensor Based on LPFG With Unique Geometric Structure
In this paper, we propose a sensor with high torsion sensitivity. This sensor has the ability to distinguish the torsion direction. A long-period fiber grating (LPFG) with a unique geometric structure is used to configure this sensor. The proposed LPFG is prepared by CO2 laser polishing method and etching method. First, we periodically polish the two opposite planes which are parallel to the axis direction of the fiber to get sheets structure. Then, the V-shaped grooves are etched on the surface orthogonal to the sheets to fabricate the proposed LPFG. Because the V-shaped grooves are arranged along the axis direction of the optical fiber, we name it by V-LPFG. This unique geometric structure results in the sensor with high torsion sensitivity. Experimental results prove that the torsion sensitivity of the proposed sensor reaches 0.399 nm/(rad/m) in the range of -10.5 rad/m to 10.5 rad/m. More importantly, the torsion sensitivity is significantly increased from 0.041 nm/(rad/m) to 0.399 nm/(rad/m) after the V-shaped grooves are etched. The temperature sensitivity of the proposed sensor is 50 pm/°C at the temperature range of 30-150 °C. Due to the high torsion sensitivity, relatively easy fabrication process and high price to quality ratio, the proposed sensor has the potential of carrying out torsion measurement with high sensitivity.
- 9 December 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 21 (5) , 6217-6223
High Torsion Sensitivity Sensor Based on LPFG With Unique Geometric Structure
In this paper, we propose a sensor with high torsion sensitivity. This sensor has the ability to distinguish the torsion direction. A long-period fiber grating (LPFG) with a unique geometric structure is used to configure this sensor. The proposed LPFG is prepared by CO2 laser polishing method and etching method. First, we periodically polish the two opposite planes which are parallel to the axis direction of the fiber to get sheets structure. Then, the V-shaped grooves are etched on the surface orthogonal to the sheets to fabricate the proposed LPFG. Because the V-shaped grooves are arranged along the axis direction of the optical fiber, we name it by V-LPFG. This unique geometric structure results in the sensor with high torsion sensitivity. Experimental results prove that the torsion sensitivity of the proposed sensor reaches 0.399 nm/(rad/m) in the range of -10.5 rad/m to 10.5 rad/m. More importantly, the torsion sensitivity is significantly increased from 0.041 nm/(rad/m) to 0.399 nm/(rad/m) after the V-shaped grooves are etched. The temperature sensitivity of the proposed sensor is 50 pm/°C at the temperature range of 30-150 °C. Due to the high torsion sensitivity, relatively easy fabrication process and high price to quality ratio, the proposed sensor has the potential of carrying out torsion measurement with high sensitivity.
- 27 August 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 32 (19) , 1253-1256
A New Sensor for Simultaneous Measurement of Strain and Temperature
A new cascaded structure based on two long-period fiber gratings (LPFGs) for simultaneous measurement of strain and temperature is proposed and studied. The proposed structure is cascaded by a LPFG and a S-type long-period fiber grating (S-LPFG). The LPFG is fabricated using the CO2 laser by etched method. The S-LPFG is fabricated using the CO2 laser by polished method. The grooves of the S-LPFG are staggered in opposite directions, and this special geometry results in high strain sensitivity. The experimental results show that the strain sensitivities of the two resonant dips of the cascaded structure are 16.31 pm/με and -2.42 pm/με with the range of 0-500 με, respectively. Strain sensitivity varies greatly between two dips and the resonant wavelength shifts in the opposite direction. The temperature sensitivities of the two resonant dips of the cascaded structure are 59.73 pm/°C and 60.38 pm/°C, respectively. Since the difference between temperature and strain sensitivity, matrix method can be used for simultaneous measurement of two parameters. The feasibility of the cascaded structure has been experimentally demonstrated for the simultaneous measurement. Therefore, the cascaded structure has the potential to measure strain and temperature simultaneously.
- 27 August 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 32 (19) , 1253-1256
A New Sensor for Simultaneous Measurement of Strain and Temperature
A new cascaded structure based on two long-period fiber gratings (LPFGs) for simultaneous measurement of strain and temperature is proposed and studied. The proposed structure is cascaded by a LPFG and a S-type long-period fiber grating (S-LPFG). The LPFG is fabricated using the CO2 laser by etched method. The S-LPFG is fabricated using the CO2 laser by polished method. The grooves of the S-LPFG are staggered in opposite directions, and this special geometry results in high strain sensitivity. The experimental results show that the strain sensitivities of the two resonant dips of the cascaded structure are 16.31 pm/με and -2.42 pm/με with the range of 0-500 με, respectively. Strain sensitivity varies greatly between two dips and the resonant wavelength shifts in the opposite direction. The temperature sensitivities of the two resonant dips of the cascaded structure are 59.73 pm/°C and 60.38 pm/°C, respectively. Since the difference between temperature and strain sensitivity, matrix method can be used for simultaneous measurement of two parameters. The feasibility of the cascaded structure has been experimentally demonstrated for the simultaneous measurement. Therefore, the cascaded structure has the potential to measure strain and temperature simultaneously.
- 3 August 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 32 (17) , 1117-1120
Torsion and Temperature Sensor Based on Polished MSM Structure
A novel optic-fiber torsion and temperature sensor has been proposed and fabricated by sandwiching a segment of a triangular shaped single-mode fiber between two multimode fibers. This structure provides the sensitivity of torsion, which results from the destruction of the rotational symmetry of the optical fiber. Experimental results show that the polished multimode single-mode multimode (MSM) sensor has the ability of determining the twist direction and the amount of torsion with sensitivities of 0.196 nm/(rad ·m-1) and -0.18 nm/(rad ·m-1) at dip 1455 nm and dip 1505 nm, respectively. In temperature measurement, the sensitivities provided by the two dips above are 0.058 nm/°C and 0.072 nm/°C, respectively. The stability and the feasibility of the proposed sensor are experimentally verified.
- 3 August 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 32 (17) , 1117-1120
Torsion and Temperature Sensor Based on Polished MSM Structure
A novel optic-fiber torsion and temperature sensor has been proposed and fabricated by sandwiching a segment of a triangular shaped single-mode fiber between two multimode fibers. This structure provides the sensitivity of torsion, which results from the destruction of the rotational symmetry of the optical fiber. Experimental results show that the polished multimode single-mode multimode (MSM) sensor has the ability of determining the twist direction and the amount of torsion with sensitivities of 0.196 nm/(rad ·m-1) and -0.18 nm/(rad ·m-1) at dip 1455 nm and dip 1505 nm, respectively. In temperature measurement, the sensitivities provided by the two dips above are 0.058 nm/°C and 0.072 nm/°C, respectively. The stability and the feasibility of the proposed sensor are experimentally verified.