Yoon-Seok Choi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Yoon-Seok Choi has a total of 35 co-authors. Here are the top co-authors by number of shared publications:
Srdjan Nešić
Institute for Corrosion and Multiphase Technology, Department of Chemical & Biomolecular Engineering, Ohio University, Athens, Ohio 45701
5 shared publicationsSrdjan Nesic
4 shared publications- Maryam Eslami
Institute for Corrosion and Multiphase Technology, Department of Chemical and Biomolecular Engineering, Ohio University, Athens, Ohio 45701
3 shared publications Azmi Mohammed Nor
**Petronas Research SDN BHD, 43000 Bandar Baru Bangi, Selangor, Malaysia
2 shared publicationsDavid Young
2 shared publicationsMuhammad Firdaus Suhor
**Petronas Research SDN BHD, 43000 Bandar Baru Bangi, Selangor, Malaysia
2 shared publications
Latest Publications
- 8 August 2024
- Published by Elsevier in Electrochimica Acta
- Vol. 503
Effect of formic acid on aqueous corrosion mechanisms of mild steel
- 8 August 2024
- Published by Elsevier in Electrochimica Acta
- Vol. 503
Effect of formic acid on aqueous corrosion mechanisms of mild steel
- 23 January 2024
- Published by Elsevier in Corrosion Science
- Vol. 229
Effect of formic acid (HCOOH) on the corrosion protectiveness of magnetite (Fe3O4) at elevated temperature
- 23 January 2024
- Published by Elsevier in Corrosion Science
- Vol. 229
Effect of formic acid (HCOOH) on the corrosion protectiveness of magnetite (Fe3O4) at elevated temperature
- 12 July 2023
- Published by Association for Materials Protection and Performance (AMPP) in Corrosion
- Vol. 79 (9) , 1052-1063
Effect of H2S on CO2 Corrosion of Mild Steel in High-Temperature Supercritical CO2 Conditions
The effect of H2S on the aqueous corrosion behavior of mild steel was evaluated at high-pressure and high-temperature (HPHT) conditions at a partial pressure of CO2 of 12 MPa and a temperature of 160°C. The corrosion rate of steel samples was determined by electrochemical and weight loss measurements. The surface and cross-sectional morphology and the composition of the corrosion product layers were analyzed by using surface analytical techniques (scanning electron microscopy, energy-dispersive x-ray spectroscopy, and x-ray diffraction). Results showed that the corrosion rate decreased with time and no significant difference was observed in the presence of 1,000 ppm and 2,000 ppm of H2S at HPHT CO2 conditions. Surface and cross-sectional analyses revealed that the corrosion process was governed by the formation of FeCO3 regardless of the presence of H2S. Furthermore, the corrosion behavior of mild steel in these conditions did not depend significantly on flow velocity.
- 12 July 2023
- Published by Association for Materials Protection and Performance (AMPP) in Corrosion
- Vol. 79 (9) , 1052-1063
Effect of H2S on CO2 Corrosion of Mild Steel in High-Temperature Supercritical CO2 Conditions
The effect of H2S on the aqueous corrosion behavior of mild steel was evaluated at high-pressure and high-temperature (HPHT) conditions at a partial pressure of CO2 of 12 MPa and a temperature of 160°C. The corrosion rate of steel samples was determined by electrochemical and weight loss measurements. The surface and cross-sectional morphology and the composition of the corrosion product layers were analyzed by using surface analytical techniques (scanning electron microscopy, energy-dispersive x-ray spectroscopy, and x-ray diffraction). Results showed that the corrosion rate decreased with time and no significant difference was observed in the presence of 1,000 ppm and 2,000 ppm of H2S at HPHT CO2 conditions. Surface and cross-sectional analyses revealed that the corrosion process was governed by the formation of FeCO3 regardless of the presence of H2S. Furthermore, the corrosion behavior of mild steel in these conditions did not depend significantly on flow velocity.
- 12 March 2023
- Published by Association for Materials Protection and Performance (AMPP) in Corrosion
- Vol. 79 (5) , 497-508
Effect of Flow on the Corrosion Behavior of Pipeline Steel in Supercritical CO2 Environments with Impurities
Corrosion is a major concern in transmission pipelines that transport captured CO2. While dry CO2 is noncorrosive, significant corrosion has been reported in dense-phase CO2 with trace amounts of water and impurities such as O2, H2S, SOx, and NOx. The aim of this work is to improve our understanding of the physicochemical aspects of the corrosion of carbon steels in the high-pressure environments associated with CO2 transmission pipelines. The effect of flow on the corrosion of X65 carbon steel was investigated in a series of autoclave tests with different combinations of impurity concentrations in supercritical CO2 conditions (8 MPa and 35°C). The corrosion rate of specimens was determined by weight loss measurements. The surface morphology and composition of the corrosion product layers were characterized using surface analytical techniques (scanning electron microscopy, eneregy dispersive x-ray spectroscopy, and Raman microscopy). Localized corrosion was measured via surface profilometry after corrosion products were removed. Results showed that no corrosion was observed in the supercritical CO2 with 650 ppmv of water, 50 ppmv SO2, and 100 ppmv NO, but corrosion occurred when SO2 concentration was increased to 4,500 ppmv and 40,000 ppmv of O2 was added to the system. The presence of flow significantly accelerated the corrosion of carbon steel. Furthermore, localized corrosion was observed in the presence of both O2 and flow.
- 12 March 2023
- Published by Association for Materials Protection and Performance (AMPP) in Corrosion
- Vol. 79 (5) , 497-508
Effect of Flow on the Corrosion Behavior of Pipeline Steel in Supercritical CO2 Environments with Impurities
Corrosion is a major concern in transmission pipelines that transport captured CO2. While dry CO2 is noncorrosive, significant corrosion has been reported in dense-phase CO2 with trace amounts of water and impurities such as O2, H2S, SOx, and NOx. The aim of this work is to improve our understanding of the physicochemical aspects of the corrosion of carbon steels in the high-pressure environments associated with CO2 transmission pipelines. The effect of flow on the corrosion of X65 carbon steel was investigated in a series of autoclave tests with different combinations of impurity concentrations in supercritical CO2 conditions (8 MPa and 35°C). The corrosion rate of specimens was determined by weight loss measurements. The surface morphology and composition of the corrosion product layers were characterized using surface analytical techniques (scanning electron microscopy, eneregy dispersive x-ray spectroscopy, and Raman microscopy). Localized corrosion was measured via surface profilometry after corrosion products were removed. Results showed that no corrosion was observed in the supercritical CO2 with 650 ppmv of water, 50 ppmv SO2, and 100 ppmv NO, but corrosion occurred when SO2 concentration was increased to 4,500 ppmv and 40,000 ppmv of O2 was added to the system. The presence of flow significantly accelerated the corrosion of carbon steel. Furthermore, localized corrosion was observed in the presence of both O2 and flow.
- 4 November 2022
- Published by Association for Materials Protection and Performance (AMPP) in Corrosion
- Vol. 79 (1) , 97-110
Effect of a Small Amount of Cr and Mo on Aqueous CO2 Corrosion of Low-Alloyed Steel and Formation of Protective FeCO3 in Near-Saturation Conditions
The effect of a small amount (1 wt%) of Cr or Mo on aqueous CO2 corrosion of low-alloyed steel and the formation of protective FeCO3 corrosion product layers was investigated under controlled water chemistry conditions, where the bulk saturation value of FeCO3 was maintained at near-saturated condition. Changes in CO2 corrosion rate with exposure time were monitored by linear polarization resisitance measurements. The surface morphology and the composition of the corrosion product layers were analyzed by scanning electron microscopy, energy dispersive x-ray spectroscopy, x-ray diffraction, and transmission electron microscopy. Results showed that the emergence of a continuous Fe3C layer created favorable conditions at the surface of nonalloyed steel (containing no Cr and Mo) for semiprotective FeCO3 to form even though the bulk saturation value of FeCO3 was maintained at near-saturated condition. However, semiprotective FeCO3 was not observed on the surface of 1% Cr steel and 1% Mo steel, but rather discontinuous and porous corrosion product layer was formed. Due to the hydrolysis reactions of Cr3+ and Mo3+, and the discontinuous structure of the corrosion product layers, the surface conditions for 1% Cr steel and 1% Mo steel were not favorable for the formation of FeCO3 under the experimental conditions of this study.
- 4 November 2022
- Published by Association for Materials Protection and Performance (AMPP) in Corrosion
- Vol. 79 (1) , 97-110
Effect of a Small Amount of Cr and Mo on Aqueous CO2 Corrosion of Low-Alloyed Steel and Formation of Protective FeCO3 in Near-Saturation Conditions
The effect of a small amount (1 wt%) of Cr or Mo on aqueous CO2 corrosion of low-alloyed steel and the formation of protective FeCO3 corrosion product layers was investigated under controlled water chemistry conditions, where the bulk saturation value of FeCO3 was maintained at near-saturated condition. Changes in CO2 corrosion rate with exposure time were monitored by linear polarization resisitance measurements. The surface morphology and the composition of the corrosion product layers were analyzed by scanning electron microscopy, energy dispersive x-ray spectroscopy, x-ray diffraction, and transmission electron microscopy. Results showed that the emergence of a continuous Fe3C layer created favorable conditions at the surface of nonalloyed steel (containing no Cr and Mo) for semiprotective FeCO3 to form even though the bulk saturation value of FeCO3 was maintained at near-saturated condition. However, semiprotective FeCO3 was not observed on the surface of 1% Cr steel and 1% Mo steel, but rather discontinuous and porous corrosion product layer was formed. Due to the hydrolysis reactions of Cr3+ and Mo3+, and the discontinuous structure of the corrosion product layers, the surface conditions for 1% Cr steel and 1% Mo steel were not favorable for the formation of FeCO3 under the experimental conditions of this study.
- 28 June 2019
- Published by Association for Materials Protection and Performance (AMPP) in Corrosion
- Vol. 75 (10) , 1156-1172
Strategies for Corrosion Inhibition of Carbon Steel Pipelines Under Supercritical CO2/H2S Environments
The objective of the present study was to identify and quantify the key issues that affect the integrity of carbon steel in high-pressure CO2 and CO2/H2S environments and to establish potential corrosion mitigation strategies using low Cr alloy steels and corrosion inhibitors. The experiments were performed in a 7.5 L autoclave with two combinations of CO2 partial pressure and temperature (12 MPa/80°C and 8 MPa/25°C) with different H2S concentrations (0 ppm, 100 ppm, and 200 ppm). The corrosion behavior of specimens was evaluated using electrochemical measurements and surface analytical techniques. Results showed that the addition of corrosion inhibitor decreased corrosion rate significantly from 90 mm/y to below 0.1 mm/y at supercritical CO2 condition (12 MPa CO2, 80°C). However, insufficient protection was achieved from low Cr alloy steels. The addition of small amounts of H2S reduced the corrosion rate of carbon steel in high-pressure CO2 environments. However, the corrosion rate was still higher than the targeted rate (<0.1 mm/y). Additional protection was required in order to achieve the target. Utilizing 400 ppm of an imidazoline-type corrosion inhibitor reduced the corrosion rate of carbon steel below 0.1 mm/y in a high-pressure CO2 condition with H2S. Compared to carbon steel, the corrosion resistance of low Cr steels was lower in the corresponding CO2 conditions with H2S.
- 28 June 2019
- Published by Association for Materials Protection and Performance (AMPP) in Corrosion
- Vol. 75 (10) , 1156-1172
Strategies for Corrosion Inhibition of Carbon Steel Pipelines Under Supercritical CO2/H2S Environments
The objective of the present study was to identify and quantify the key issues that affect the integrity of carbon steel in high-pressure CO2 and CO2/H2S environments and to establish potential corrosion mitigation strategies using low Cr alloy steels and corrosion inhibitors. The experiments were performed in a 7.5 L autoclave with two combinations of CO2 partial pressure and temperature (12 MPa/80°C and 8 MPa/25°C) with different H2S concentrations (0 ppm, 100 ppm, and 200 ppm). The corrosion behavior of specimens was evaluated using electrochemical measurements and surface analytical techniques. Results showed that the addition of corrosion inhibitor decreased corrosion rate significantly from 90 mm/y to below 0.1 mm/y at supercritical CO2 condition (12 MPa CO2, 80°C). However, insufficient protection was achieved from low Cr alloy steels. The addition of small amounts of H2S reduced the corrosion rate of carbon steel in high-pressure CO2 environments. However, the corrosion rate was still higher than the targeted rate (<0.1 mm/y). Additional protection was required in order to achieve the target. Utilizing 400 ppm of an imidazoline-type corrosion inhibitor reduced the corrosion rate of carbon steel below 0.1 mm/y in a high-pressure CO2 condition with H2S. Compared to carbon steel, the corrosion resistance of low Cr steels was lower in the corresponding CO2 conditions with H2S.
- 1 May 2018
- Published by Association for Materials Protection and Performance (AMPP) in Corrosion
- Vol. 74 (5) , 566-576
Effect of Alloying Elements on the Corrosion Behavior of Carbon Steel in CO2 Environments
The objective of the present study was to evaluate the effect of alloying elements (Cr, Mo, and Cu) on the corrosion behavior of low carbon steel in CO2 environments. Six samples were prepared with varying Cr content from 0 wt% to 2 wt% and with added 0.5 wt% of Mo and Cu; the specimens had ferritic/pearlitic microstructures. Steel samples were exposed to a CO2-saturated 1 wt% NaCl solution with different combinations of pH and temperature (pH 4.0 at 25°C, pH 6.6 at 80°C, and pH 5.9 at 70°C). Changes in corrosion rate with time were determined by linear polarization resistance measurements. The surface morphology and the composition of the corrosion product layers were analyzed by surface analysis techniques (scanning electron microscopy and energy dispersive x-ray spectroscopy). Results showed that the presence of Cr and Cu showed a slight positive effect on the corrosion resistance at pH 4.0 and 25°C. At pH 6.6 and 80°C, regardless of the alloying elements, the trend of corrosion rate with time was similar, i.e., the corrosion rate of all specimens decreased with time resulting from the formation of protective FeCO3. A beneficial effect of Cr presence was clearly seen at “gray zone” conditions: pH 5.9 and 70°C, where steel sample without Cr showed no decrease in corrosion rate with time. The presence of Cr in the steel promoted the formation of protective FeCO3 with Cr enrichment and it decreased the corrosion rate.
- 1 May 2018
- Published by Association for Materials Protection and Performance (AMPP) in Corrosion
- Vol. 74 (5) , 566-576
Effect of Alloying Elements on the Corrosion Behavior of Carbon Steel in CO2 Environments
The objective of the present study was to evaluate the effect of alloying elements (Cr, Mo, and Cu) on the corrosion behavior of low carbon steel in CO2 environments. Six samples were prepared with varying Cr content from 0 wt% to 2 wt% and with added 0.5 wt% of Mo and Cu; the specimens had ferritic/pearlitic microstructures. Steel samples were exposed to a CO2-saturated 1 wt% NaCl solution with different combinations of pH and temperature (pH 4.0 at 25°C, pH 6.6 at 80°C, and pH 5.9 at 70°C). Changes in corrosion rate with time were determined by linear polarization resistance measurements. The surface morphology and the composition of the corrosion product layers were analyzed by surface analysis techniques (scanning electron microscopy and energy dispersive x-ray spectroscopy). Results showed that the presence of Cr and Cu showed a slight positive effect on the corrosion resistance at pH 4.0 and 25°C. At pH 6.6 and 80°C, regardless of the alloying elements, the trend of corrosion rate with time was similar, i.e., the corrosion rate of all specimens decreased with time resulting from the formation of protective FeCO3. A beneficial effect of Cr presence was clearly seen at “gray zone” conditions: pH 5.9 and 70°C, where steel sample without Cr showed no decrease in corrosion rate with time. The presence of Cr in the steel promoted the formation of protective FeCO3 with Cr enrichment and it decreased the corrosion rate.
- 3 September 2014
- Published by Association for Materials Protection and Performance (AMPP) in Corrosion
- Vol. 71 (1) , 30-37
Corrosion of Carbon Steel in MDEA-Based CO2 Capture Plants Under Regenerator Conditions: Effects of O2 and Heat-Stable Salts
The corrosion behavior of carbon steel UNS K02600 in 50 wt% methyldiethanolamine solutions was investigated in the back-ground of the carbon dioxide (CO2) capture process in fossil fuel-fired power plants for the purpose of carbon capture and storage. A series of experiments was conducted under regenerator conditions (120°C) with different combinations of CO2 loading (0.3 mol/mol and 0.05 mol/mol), O2, and heat-stable salts (including sulfate, formate, and N,N-bis[2-hydroxyethyl] glycine). The corrosion behavior of carbon steel was investigated using electrochemical techniques (open circuit potential, linear polarization resistance, and potentiodynamic polarization), surface analytical techniques (scanning electron microscopy, energy-dispersive x-ray spectroscopy, and x-ray diffraction), and weight-loss methods. The results showed that the corrosion rate of carbon steel initially decreased and then stabilized with time in CO2-loaded methyldiethanolamine solution due to the formation of an iron carbonate (FeCO3) layer, with the exception of methyldiethanolamine/CO2/O2/heat-stable salts, which exhibited a low CO2 loading (0.05 mol/mol). It was found that the presence of HSS significantly accelerated the corrosion process at low CO2 loading, whereas the effect of oxygen on the corrosion rate was not significant at low CO2 loading. The formation mechanism of the FeCO3 layer, which is a key issue in the control of corrosion in these environments, was discussed.
- 3 September 2014
- Published by Association for Materials Protection and Performance (AMPP) in Corrosion
- Vol. 71 (1) , 30-37
Corrosion of Carbon Steel in MDEA-Based CO2 Capture Plants Under Regenerator Conditions: Effects of O2 and Heat-Stable Salts
The corrosion behavior of carbon steel UNS K02600 in 50 wt% methyldiethanolamine solutions was investigated in the back-ground of the carbon dioxide (CO2) capture process in fossil fuel-fired power plants for the purpose of carbon capture and storage. A series of experiments was conducted under regenerator conditions (120°C) with different combinations of CO2 loading (0.3 mol/mol and 0.05 mol/mol), O2, and heat-stable salts (including sulfate, formate, and N,N-bis[2-hydroxyethyl] glycine). The corrosion behavior of carbon steel was investigated using electrochemical techniques (open circuit potential, linear polarization resistance, and potentiodynamic polarization), surface analytical techniques (scanning electron microscopy, energy-dispersive x-ray spectroscopy, and x-ray diffraction), and weight-loss methods. The results showed that the corrosion rate of carbon steel initially decreased and then stabilized with time in CO2-loaded methyldiethanolamine solution due to the formation of an iron carbonate (FeCO3) layer, with the exception of methyldiethanolamine/CO2/O2/heat-stable salts, which exhibited a low CO2 loading (0.05 mol/mol). It was found that the presence of HSS significantly accelerated the corrosion process at low CO2 loading, whereas the effect of oxygen on the corrosion rate was not significant at low CO2 loading. The formation mechanism of the FeCO3 layer, which is a key issue in the control of corrosion in these environments, was discussed.