Mustafa Kiliç
Research Subjects
Mustafa Kiliç has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Mahir Şahin
Adana Alparslan Turkes Bilim ve Teknoloji Universitesi
7 shared publications - Senol Baskaya
University of Kyrenia
5 shared publications - Tamer Calisir
Gazi University, Turkey
4 shared publications - Aslı Abdulvahitoğlu
Adana Alparslan Turkes Bilim ve Teknoloji Universitesi
2 shared publications - Merve Ala
Adana Alparslan Turkes Bilim ve Teknoloji Universitesi
2 shared publications - Abdurrahim Dal
Mechanical Engineering Department, Adana Alparslan Türkeş Science and Technology University, Adana, Turkey
1 shared publication
Latest Publications
- Open Access
- 29 December 2025
- Published by International Journal of Innovative Engineering Applications in International Journal of Innovative Engineering Applications
- Vol. 9 (2) , 201-210
Investigation of the Impact of Porous Structure Geometry and Flow Characteristics on Heat Transfer Effectiveness in a Shell-and-Tube Heat Exchanger
The present study investigates the effects of Reynolds number, fluid inlet temperature, porosity ratio, and porous thickness on the heat transfer effectiveness of a shell-and-tube heat exchanger operating under laminar flow conditions. The primary objective of the study is to determine how these parameters influence thermal performance and to establish a clear understanding of their roles in enhancing heat transfer effectiveness. The investigated parameters are Reynolds numbers of 1000, 2000, 3000, and 4000; inlet temperatures of 25°C, 30°C, 35°C, and 40°C; porosity ratios of 0.5, 0.6, 0.8, and 0.9; and porous thicknesses of 5/80, 10/80, 15/80, and 20/80. Numerical model validated by experimental data shows that at Re = 1000, the heat transfer effectiveness of pure water at 40°C is 1.1% higher than that at 25°C, while this difference increases to 1.9% at Re = 4000. When the inlet temperature is raised from 25°C to 40°C, the average enhancement in effectiveness is 1.7% for each Re value. At constant inlet temperature, increasing the Reynolds number from 1000 to 4000 improves the heat transfer effectiveness by 12.8%. The results confirm that heat transfer effectiveness (ε) increases with fluid inlet temperature across all Re values. Furthermore, at Re = 1000, a porosity ratio of Φ = 0.9 yields 1.3% higher effectiveness compared to 0.5 at the same temperature. Similarly, for porous thickness L/D (porous thickness/pipe diameter), a structure with 20/80 provides 2.2% higher effectiveness than 5/80 under identical conditions. These findings demonstrate that optimizing porosity and porous thickness, along with flow and temperature parameters, can significantly enhance heat transfer performance. The results indicate that shell-and-tube heat exchangers with porous inserts can be designed to achieve higher thermal effectiveness and improved energy efficiency in future applications.
- 29 December 2025
- Published by International Journal of Innovative Engineering Applications in International Journal of Innovative Engineering Applications
- Vol. 9 (2) , 201-210
Open AccessInvestigation of the Impact of Porous Structure Geometry and Flow Characteristics on Heat Transfer Effectiveness in a Shell-and-Tube Heat Exchanger
The present study investigates the effects of Reynolds number, fluid inlet temperature, porosity ratio, and porous thickness on the heat transfer effectiveness of a shell-and-tube heat exchanger operating under laminar flow conditions. The primary objective of the study is to determine how these parameters influence thermal performance and to establish a clear understanding of their roles in enhancing heat transfer effectiveness. The investigated parameters are Reynolds numbers of 1000, 2000, 3000, and 4000; inlet temperatures of 25°C, 30°C, 35°C, and 40°C; porosity ratios of 0.5, 0.6, 0.8, and 0.9; and porous thicknesses of 5/80, 10/80, 15/80, and 20/80. Numerical model validated by experimental data shows that at Re = 1000, the heat transfer effectiveness of pure water at 40°C is 1.1% higher than that at 25°C, while this difference increases to 1.9% at Re = 4000. When the inlet temperature is raised from 25°C to 40°C, the average enhancement in effectiveness is 1.7% for each Re value. At constant inlet temperature, increasing the Reynolds number from 1000 to 4000 improves the heat transfer effectiveness by 12.8%. The results confirm that heat transfer effectiveness (ε) increases with fluid inlet temperature across all Re values. Furthermore, at Re = 1000, a porosity ratio of Φ = 0.9 yields 1.3% higher effectiveness compared to 0.5 at the same temperature. Similarly, for porous thickness L/D (porous thickness/pipe diameter), a structure with 20/80 provides 2.2% higher effectiveness than 5/80 under identical conditions. These findings demonstrate that optimizing porosity and porous thickness, along with flow and temperature parameters, can significantly enhance heat transfer performance. The results indicate that shell-and-tube heat exchangers with porous inserts can be designed to achieve higher thermal effectiveness and improved energy efficiency in future applications.
- Open Access
- 2 July 2025
- Published by Cukurova Universitesi Muhendislik-Mimarlik Fakultesi Dergisi in Çukurova Üniversitesi Mühendislik Fakültesi Dergisi
- Vol. 40 (2) , 375-386
An Investigation on Design Criteria of Heat Exchangers by Using Tree Models of Machine Learning Methods
Heat exchangers are critical components widely used in various industries such as chemical processing, automotive, and HVAC. The evaluation and optimization of heat exchanger design criteria play a vital role in improving industrial applications. Tree-based machine learning models offer a powerful alternative to time-consuming numerical solutions by enabling optimization and classification predictions for problems involving small, medium, or large datasets. This study aims to analyze heat exchanger design criteria using tree-based machine learning models and to identify the most suitable model for each design parameter. As a result, it has been evaluated that the XGBoost model provides effective solutions for design criteria such as heat transfer rate, safety, and reliability; the AdaBoost model is more suitable for criteria such as exchanger type and ease of maintenance; and the RF model performs well for cost and pumping power. It is anticipated that in the future, analyzing heat exchanger design parameters using various machine learning approaches will enable the development of more cost-effective and efficient heat exchangers.
- 2 July 2025
- Published by Cukurova Universitesi Muhendislik-Mimarlik Fakultesi Dergisi in Çukurova Üniversitesi Mühendislik Fakültesi Dergisi
- Vol. 40 (2) , 375-386
Open AccessAn Investigation on Design Criteria of Heat Exchangers by Using Tree Models of Machine Learning Methods
Heat exchangers are critical components widely used in various industries such as chemical processing, automotive, and HVAC. The evaluation and optimization of heat exchanger design criteria play a vital role in improving industrial applications. Tree-based machine learning models offer a powerful alternative to time-consuming numerical solutions by enabling optimization and classification predictions for problems involving small, medium, or large datasets. This study aims to analyze heat exchanger design criteria using tree-based machine learning models and to identify the most suitable model for each design parameter. As a result, it has been evaluated that the XGBoost model provides effective solutions for design criteria such as heat transfer rate, safety, and reliability; the AdaBoost model is more suitable for criteria such as exchanger type and ease of maintenance; and the RF model performs well for cost and pumping power. It is anticipated that in the future, analyzing heat exchanger design parameters using various machine learning approaches will enable the development of more cost-effective and efficient heat exchangers.
- Open Access
- 25 December 2024
- Published by Cukurova Universitesi Muhendislik-Mimarlik Fakultesi Dergisi in Çukurova Üniversitesi Mühendislik Fakültesi Dergisi
- Vol. 39 (4) , 951-959
Experimental Investigation of the Effect of Different Parameters on Plate and Frame Heat Exchanger Effectiveness
Plate & frame heat exchangers use a series of metal plates to conduct heat transfer between fluids. These fluids are directed through specific channels, ensuring they remain isolated while allowing efficient heat exchange. In recent years, researchers have looked at how different characteristics affect heat exchanger performance. The purpose of this study is to examine the impact of various factors on the effectiveness of the heat exchanger. The experimental analysis was conducted using pure water, considering different Re numbers ranging from 6000 to 30000 and varying hot fluid inlet temperatures between 25℃ and 35℃. It was observed that under turbulent flow conditions, the heat transfer effectiveness increased of 13.6% when the Reynolds number varied between Re = 6000 – 20000 at constant Th,in=35℃. However, the extent of this increase diminished significantly within the Re = 20000-30000 range. When the inlet temperature of hot fluid was raised Th,in=25℃ to 35℃ the plate & frame heat exchanger effectiveness increased of 4.3%. This study provides a basis for future studies on heat exchangers used in industrial applications with different geometries and different fluids. It is considered that the results of this study could be used in the future to design more modular and efficient plate heat exchangers for industrial applications.
- 25 December 2024
- Published by Cukurova Universitesi Muhendislik-Mimarlik Fakultesi Dergisi in Çukurova Üniversitesi Mühendislik Fakültesi Dergisi
- Vol. 39 (4) , 951-959
Open AccessExperimental Investigation of the Effect of Different Parameters on Plate and Frame Heat Exchanger Effectiveness
Plate & frame heat exchangers use a series of metal plates to conduct heat transfer between fluids. These fluids are directed through specific channels, ensuring they remain isolated while allowing efficient heat exchange. In recent years, researchers have looked at how different characteristics affect heat exchanger performance. The purpose of this study is to examine the impact of various factors on the effectiveness of the heat exchanger. The experimental analysis was conducted using pure water, considering different Re numbers ranging from 6000 to 30000 and varying hot fluid inlet temperatures between 25℃ and 35℃. It was observed that under turbulent flow conditions, the heat transfer effectiveness increased of 13.6% when the Reynolds number varied between Re = 6000 – 20000 at constant Th,in=35℃. However, the extent of this increase diminished significantly within the Re = 20000-30000 range. When the inlet temperature of hot fluid was raised Th,in=25℃ to 35℃ the plate & frame heat exchanger effectiveness increased of 4.3%. This study provides a basis for future studies on heat exchangers used in industrial applications with different geometries and different fluids. It is considered that the results of this study could be used in the future to design more modular and efficient plate heat exchangers for industrial applications.
- 19 October 2024
- Published by Springer Nature in Journal of Thermal Analysis and Calorimetry
- Vol. 149 (22) , 13081-13093
A new approach for enhancing the effectiveness of a regenerative heat exchanger by using organic and inorganic phase change material
- 19 October 2024
- Published by Springer Nature in Journal of Thermal Analysis and Calorimetry
- Vol. 149 (22) , 13081-13093
A new approach for enhancing the effectiveness of a regenerative heat exchanger by using organic and inorganic phase change material
- Open Access
- 28 December 2023
- Published by Cukurova Universitesi Muhendislik-Mimarlik Fakultesi Dergisi in Çukurova Üniversitesi Mühendislik Fakültesi Dergisi
- Vol. 38 (4) , 1117-1128
Investigation of the Effect of Different Parameters of Phase Change Materials on Heat Exchanger Performance
Technological improvements and increasing energy demand necessitate energy efficient designs for heat transfer systems. The storage and reuse of heat energy plays an important role in the development of energy-efficient systems. Phase change materials (PCMs) are crucial components which increase energy efficiency in heat exchangers as can be applied to many systems. In this study, the heat transfer performance of different types of phase change materials in a regenerative heat exchanger was investigated according to different parameters. Reynolds number depending on the hot fluid velocity (Re=400, 800, 1200, 1600), hot fluid inlet temperature (Tsıcak,giriş=40, 60, 70, 80℃), and different types of phase change materials (RT60, RT100, and SP70) are the parameters used in this study. ANSYS Fluent software was used for computational fluid dynamics analysis. As a result, it has been determined that when the Reynolds number of the hot fluid in the heat exchanger was increased in the range of Re=400-1600, the heat transfer effectiveness increase of 17%; when the hot fluid inlet temperature was increased in the range of Thot,inlet=40-80℃, the heat transfer effectiveness increase of 21%. As regards the effect of different types of phase change materials, the heat transfer effectiveness was 81% for RT60, 79% for SP70 and 76% for RT100. It has been evaluated that, with the results obtained from this study, heat exchangers with higher heat transfer effectiveness and higher energy storage capacity can be designed.
- 28 December 2023
- Published by Cukurova Universitesi Muhendislik-Mimarlik Fakultesi Dergisi in Çukurova Üniversitesi Mühendislik Fakültesi Dergisi
- Vol. 38 (4) , 1117-1128
Open AccessInvestigation of the Effect of Different Parameters of Phase Change Materials on Heat Exchanger Performance
Technological improvements and increasing energy demand necessitate energy efficient designs for heat transfer systems. The storage and reuse of heat energy plays an important role in the development of energy-efficient systems. Phase change materials (PCMs) are crucial components which increase energy efficiency in heat exchangers as can be applied to many systems. In this study, the heat transfer performance of different types of phase change materials in a regenerative heat exchanger was investigated according to different parameters. Reynolds number depending on the hot fluid velocity (Re=400, 800, 1200, 1600), hot fluid inlet temperature (Tsıcak,giriş=40, 60, 70, 80℃), and different types of phase change materials (RT60, RT100, and SP70) are the parameters used in this study. ANSYS Fluent software was used for computational fluid dynamics analysis. As a result, it has been determined that when the Reynolds number of the hot fluid in the heat exchanger was increased in the range of Re=400-1600, the heat transfer effectiveness increase of 17%; when the hot fluid inlet temperature was increased in the range of Thot,inlet=40-80℃, the heat transfer effectiveness increase of 21%. As regards the effect of different types of phase change materials, the heat transfer effectiveness was 81% for RT60, 79% for SP70 and 76% for RT100. It has been evaluated that, with the results obtained from this study, heat exchangers with higher heat transfer effectiveness and higher energy storage capacity can be designed.
- Open Access
- 30 November 2023
- Published by Yildiz Technical University in Journal of Thermal Engineering
- Vol. 9 (6) , 1604-1617
A thermohydrodynamic performance analysis of a fluid film bearing considering with geometrical parameters
Bearing performance characteristics such as stiffness, and load capacity, are related to the lubrication fluid circulating through the gap. In the fluid film bearings, the characteristic of the lubrication film also depends on the journal geometry and the viscosity. This study aimed to research the bearing geometry influences on the thermohydrodynamic performance of a circular journal bearing. The temperature distribution is modeled using a 3-dimensional energy equation. The velocity components are obtained on the pressure distribution governed by Dowson’s equation. Moreover, the heat transfer between the journal and oil is modeled with Fourier heat conduction equation, and the viscosity equation is derived for SAE10W30 commercial oil as a function of the temperature. An algorithm based on the finite difference method is developed, and a serial simulation is performed for different geometrical parame-ters such as bearing clearance, and bearing length-to-diameter ratio (L/D). When the radial clearance decreases from 150 µm to 100 µm, the maximum pressure grows up by 53%, and the maximum temperature decreases by 21%. On the other hand, when the L/D ratio rises from 0.8 to 1, the maximum pressure grows up by 22%, but the temperature distribution does not significantly change. The load capacity, and the stiffness are higher for low radial clearance. The load capacity, and the stiffness increase when the L/D ratio grows up.
- 30 November 2023
- Published by Yildiz Technical University in Journal of Thermal Engineering
- Vol. 9 (6) , 1604-1617
Open AccessA thermohydrodynamic performance analysis of a fluid film bearing considering with geometrical parameters
Bearing performance characteristics such as stiffness, and load capacity, are related to the lubrication fluid circulating through the gap. In the fluid film bearings, the characteristic of the lubrication film also depends on the journal geometry and the viscosity. This study aimed to research the bearing geometry influences on the thermohydrodynamic performance of a circular journal bearing. The temperature distribution is modeled using a 3-dimensional energy equation. The velocity components are obtained on the pressure distribution governed by Dowson’s equation. Moreover, the heat transfer between the journal and oil is modeled with Fourier heat conduction equation, and the viscosity equation is derived for SAE10W30 commercial oil as a function of the temperature. An algorithm based on the finite difference method is developed, and a serial simulation is performed for different geometrical parame-ters such as bearing clearance, and bearing length-to-diameter ratio (L/D). When the radial clearance decreases from 150 µm to 100 µm, the maximum pressure grows up by 53%, and the maximum temperature decreases by 21%. On the other hand, when the L/D ratio rises from 0.8 to 1, the maximum pressure grows up by 22%, but the temperature distribution does not significantly change. The load capacity, and the stiffness are higher for low radial clearance. The load capacity, and the stiffness increase when the L/D ratio grows up.
- 28 July 2023
- Published by Cukurova Universitesi Muhendislik-Mimarlik Fakultesi Dergisi in Çukurova Üniversitesi Mühendislik Fakültesi Dergisi
- Vol. 38 (2) , 531-543
Experimental and Numerical Investigation of the Effect of Nanofluid Volume Ratio and Particle Size on Heat Transfer in a Shell-and-Tube Heat Exchanger
Bu deneysel çalışmanın amacı, farklı parametrelerin gövde borulu ısı değiştiricisinde meydana gelen ısı transferine ve akış özelliklerine etkisini sayısal olarak incelemek ve deneysel olarak doğrulamaktır. Çalışmada kullanılan parametreler; sıcak akışkan Re sayısı, TiO2/H2O nanoakışkanın hacimsel konsantrasyonu ve nanoakışkan oluşturulmasında kullanılan nanoparçacık boyutudur. Çalışmanın sayısal sonuçları ANSYS Fluent Hesaplamalı Akışkanlar Dinamiği programını kullanılarak elde edilmiş ve deneysel sonuçlarla doğrulanmıştır. Çalışmanın birinci aşamasında yapılan deneysel çalışmada; farklı Re sayılarının (Re=1000, 1500, 2000, 2200) gövde borulu ısı değiştiricisi etkinliğine olan etkisi incelenmiştir. Çalışmanın ikinci aşamasında; sayısal sonuçlar deney sonuçları ile doğrulanmış ve farklı iki parametrenin (nanoakışkan hacimsel konsantrasyonu (%0,2, 0,4, 0,8, 1,6) ve nanoparçacık boyutu (Dp=5, 10, 20 40 nm) ısı değiştiricisi etkinliğine olan etkisi incelenmiştir. Sonuç olarak; sıcak akışkan giriş sıcaklığı Tsıcak,giriş=50 ℃’de sabit iken Re sayısı Re=1000-2200 aralığında arttırıldığında ısı transfer etkinliğinde %6,15 azalma tespit edilmiştir. Sayısal olarak oluşturulan Dp=10 nm parçacık boyutlu TiO2/H2O nanoakışkanı için sabit giriş sıcaklığı (Tsıcak,giriş=50 ℃), sabit Re sayısında (Re=1000) nanoparçacık hacimsel konsantrasyonu φ=%0,2-1,6 aralığında arttırıldığında ısı transfer etkinliğinde %8 artış tespit edilmiştir. Nanoparçacık boyutunun etkisini incelemek için aynı şartlarda ve φ=0,2 hacimsel konsantrasyonda parçacık boyutu Dp=5-40 aralığında arttırıldığında ısı transfer etkinliğinde %1 azalma tespit edilmiştir. Bu çalışma sonucunda elde edilen veriler kullanılarak gelecekte, daha yüksek performanslı ısı değiştiricilerin tasarlanabileceği değerlendirilmiştir.
- 28 July 2023
- Published by Cukurova Universitesi Muhendislik-Mimarlik Fakultesi Dergisi in Çukurova Üniversitesi Mühendislik Fakültesi Dergisi
- Vol. 38 (2) , 531-543
Experimental and Numerical Investigation of the Effect of Nanofluid Volume Ratio and Particle Size on Heat Transfer in a Shell-and-Tube Heat Exchanger
Bu deneysel çalışmanın amacı, farklı parametrelerin gövde borulu ısı değiştiricisinde meydana gelen ısı transferine ve akış özelliklerine etkisini sayısal olarak incelemek ve deneysel olarak doğrulamaktır. Çalışmada kullanılan parametreler; sıcak akışkan Re sayısı, TiO2/H2O nanoakışkanın hacimsel konsantrasyonu ve nanoakışkan oluşturulmasında kullanılan nanoparçacık boyutudur. Çalışmanın sayısal sonuçları ANSYS Fluent Hesaplamalı Akışkanlar Dinamiği programını kullanılarak elde edilmiş ve deneysel sonuçlarla doğrulanmıştır. Çalışmanın birinci aşamasında yapılan deneysel çalışmada; farklı Re sayılarının (Re=1000, 1500, 2000, 2200) gövde borulu ısı değiştiricisi etkinliğine olan etkisi incelenmiştir. Çalışmanın ikinci aşamasında; sayısal sonuçlar deney sonuçları ile doğrulanmış ve farklı iki parametrenin (nanoakışkan hacimsel konsantrasyonu (%0,2, 0,4, 0,8, 1,6) ve nanoparçacık boyutu (Dp=5, 10, 20 40 nm) ısı değiştiricisi etkinliğine olan etkisi incelenmiştir. Sonuç olarak; sıcak akışkan giriş sıcaklığı Tsıcak,giriş=50 ℃’de sabit iken Re sayısı Re=1000-2200 aralığında arttırıldığında ısı transfer etkinliğinde %6,15 azalma tespit edilmiştir. Sayısal olarak oluşturulan Dp=10 nm parçacık boyutlu TiO2/H2O nanoakışkanı için sabit giriş sıcaklığı (Tsıcak,giriş=50 ℃), sabit Re sayısında (Re=1000) nanoparçacık hacimsel konsantrasyonu φ=%0,2-1,6 aralığında arttırıldığında ısı transfer etkinliğinde %8 artış tespit edilmiştir. Nanoparçacık boyutunun etkisini incelemek için aynı şartlarda ve φ=0,2 hacimsel konsantrasyonda parçacık boyutu Dp=5-40 aralığında arttırıldığında ısı transfer etkinliğinde %1 azalma tespit edilmiştir. Bu çalışma sonucunda elde edilen veriler kullanılarak gelecekte, daha yüksek performanslı ısı değiştiricilerin tasarlanabileceği değerlendirilmiştir.
- Open Access
- 6 January 2023
- Published by Journal of the Faculty of Engineering and Architecture of Gazi University in Gazi Üniversitesi Mühendislik-Mimarlık Fakültesi Dergisi
- Vol. 38 (3) , 1805-1820
Karışık taşınım ile olan ısı transferinin farklı geometrideki akış engelleri kullanılarak iyileştirilmesinin sayısal olarak incelenmesi
Bu çalışmada; içinde ısı akısına sahip, farklı konum ve geometride engeller bulunan dik bir kanaldaki karışık konveksiyonun ısı transferine ve akış özelliklerine etkisi sayısal olarak incelenmiştir. Engellerin konumları, sayıları ve geometrileri değiştirilerek ısı transferine ve akış özelliklerine etkisi belirlenmeye çalışılmıştır. Çalışmada, alt alta bulunan iki yarı silindirik engelin, alt alta ve karşılıklı bulunan dört yarı silindirik engelin ve alt alta ve karşılıklı bulunan dört dikdörtgen engelin karışık konveksiyonla olan akış ve ısı transferine etkileri irdelenmiştir. Sonuç olarak; Nusselt sayısının, engellerin birbirine olan uzaklıklarının (L/D oranı) ve doğal taşınım etkilerinin (Ri sayısı) artmasıyla genel olarak arttığı tespit edilmiştir. Her iki engel geometrisinde (yarı silindirik engel ve dikdörtgen engel) L/D oranının ve değiştirilmiş Ri sayısının arttırılmasının Nusselt sayısına olan etkisinin benzer olduğu ve ısı transferini arttırdığı tespit edilmiştir. Yarı silindirik engeldeki Nusselt değerlerinin dikdörtgen engeldeki Nusselt değerlerine kıyasla daha büyük olduğu belirlenmiştir. Yarı silindirik engeldeki Nusselt değerlerinin dikdörtgen engeldeki Nusselt değerlerinden farkının; engeller arası mesafenin az olduğu (L/D=0,25) değer için; düşük Ri sayılarında (Ri=50) %72,5 iken yüksek Ri sayılarında (Ri=200) %19,6 olduğu tespit edilmiştir. Bu fark; engeller arası mesafenin çok olduğu (L/D=1,5) değer için; düşük Ri sayılarında (Ri=50) %58,6 iken yüksek Ri sayılarında (Ri=200) %39,1 olduğu tespit edilmiştir. Her iki engel geometrisinde de en yüksek Nu sayısının L/D= 1,5 ve Ri=200 olduğu durumda meydana geldiği belirlenmiştir. Ayrıca; çalışmada Nu sayısı için bir korelasyon elde edilmiştir. Sayısal çalışmanın sonuçları literatürde bulunan deneysel çalışmalarla da karşılaştırılarak; sıcaklık dağılımını ve akış özelliklerini iyi şekilde temsil edebildiği görülmüştür.
- 6 January 2023
- Published by Journal of the Faculty of Engineering and Architecture of Gazi University in Gazi Üniversitesi Mühendislik-Mimarlık Fakültesi Dergisi
- Vol. 38 (3) , 1805-1820
Open AccessKarışık taşınım ile olan ısı transferinin farklı geometrideki akış engelleri kullanılarak iyileştirilmesinin sayısal olarak incelenmesi
Bu çalışmada; içinde ısı akısına sahip, farklı konum ve geometride engeller bulunan dik bir kanaldaki karışık konveksiyonun ısı transferine ve akış özelliklerine etkisi sayısal olarak incelenmiştir. Engellerin konumları, sayıları ve geometrileri değiştirilerek ısı transferine ve akış özelliklerine etkisi belirlenmeye çalışılmıştır. Çalışmada, alt alta bulunan iki yarı silindirik engelin, alt alta ve karşılıklı bulunan dört yarı silindirik engelin ve alt alta ve karşılıklı bulunan dört dikdörtgen engelin karışık konveksiyonla olan akış ve ısı transferine etkileri irdelenmiştir. Sonuç olarak; Nusselt sayısının, engellerin birbirine olan uzaklıklarının (L/D oranı) ve doğal taşınım etkilerinin (Ri sayısı) artmasıyla genel olarak arttığı tespit edilmiştir. Her iki engel geometrisinde (yarı silindirik engel ve dikdörtgen engel) L/D oranının ve değiştirilmiş Ri sayısının arttırılmasının Nusselt sayısına olan etkisinin benzer olduğu ve ısı transferini arttırdığı tespit edilmiştir. Yarı silindirik engeldeki Nusselt değerlerinin dikdörtgen engeldeki Nusselt değerlerine kıyasla daha büyük olduğu belirlenmiştir. Yarı silindirik engeldeki Nusselt değerlerinin dikdörtgen engeldeki Nusselt değerlerinden farkının; engeller arası mesafenin az olduğu (L/D=0,25) değer için; düşük Ri sayılarında (Ri=50) %72,5 iken yüksek Ri sayılarında (Ri=200) %19,6 olduğu tespit edilmiştir. Bu fark; engeller arası mesafenin çok olduğu (L/D=1,5) değer için; düşük Ri sayılarında (Ri=50) %58,6 iken yüksek Ri sayılarında (Ri=200) %39,1 olduğu tespit edilmiştir. Her iki engel geometrisinde de en yüksek Nu sayısının L/D= 1,5 ve Ri=200 olduğu durumda meydana geldiği belirlenmiştir. Ayrıca; çalışmada Nu sayısı için bir korelasyon elde edilmiştir. Sayısal çalışmanın sonuçları literatürde bulunan deneysel çalışmalarla da karşılaştırılarak; sıcaklık dağılımını ve akış özelliklerini iyi şekilde temsil edebildiği görülmüştür.
- Open Access
- 30 December 2022
- Published by Cukurova Universitesi Muhendislik-Mimarlik Fakultesi Dergisi in Çukurova Üniversitesi Mühendislik Fakültesi Dergisi
- Vol. 37 (4) , 1061-1076
Elektrikli Araç Bataryalarının Bütünleşik Swara-Topsis Metodu ile Değerlendirilmesi
Küreselleşme ve dünya nüfusundaki hızlı artış birçok sorunu da beraberinde getirmektedir. Bunlardan birisi de İçten Yanmalı Motorla çalışan araçların neden olduğu ulaşım, trafik ve çevre sorunudur. Bu yüzden bilim insanları bir yandan ulaşım ve trafik sorununu çözmeye çalışırken diğer yandan yenilenebilir ve çevre dostu alternatif enerji kaynakları ile bunları kullanan araçlar üzerine yoğunlaştırmaktadır. Özellikle elektrik makinaları, bataryalar ve güç elektroniği alanlarında yaşanan teknolojik gelişmeler, girişimcileri elektrikli araç üretimine yönlendirmektedir. Elektrikli Araç çalışmalarında yaşanan ilerlemeler sayesinde batarya ile çalışan Elektrikli araçlar yavaş yavaş fosil yakıt kullanan araçların yerini almaya başlamıştır. Ancak daha iyi performans gösterecek batarya geliştirme çalışmaları devam ettiğinden elektrikli araç kullanımı yavaş, fakat hızlanarak devam etmektedir. Batarya geliştirme çalışmalarında öncelikle hızlı şarj, taşıt menzili, uzun pil ömrü, düşük maliyet, batarya kapasitesi, şarj süresi, batarya verimi ve batarya güç değeri vb. gereksinimler karşılanmaya çalışılmaktadır. Bu noktada Lityum-İyon bataryalar ön plana çıkmaktadır. Ancak geliştirilen Lityum-İyon batarya çeşitlerinin değişik performans özellikleri, Elektrikli Araç üreticilerinin batarya seçiminde karar vermelerini zorlaştırmaktadır. Bu çalışmada Çok Kriterli Karar Verme yöntemlerinden Adım Adım Ağırlık Değerlendirme Oran Analizi ve İdeal Çözüme Benzerliğe Göre Tercih Sıralama kullanılarak, karar vericilere Lityum-İyon batarya seçiminde yardımcı olacak bir model önerilmiştir. Böylece Elektrikli Araç üretim çalışmalarında yer alan işletmelere en uygun bataryayı seçme, elektrikli araçların maliyetini azaltma ve performanslarını artırma çalışmalarında faydalı olunması öngörülmektedir.
- 30 December 2022
- Published by Cukurova Universitesi Muhendislik-Mimarlik Fakultesi Dergisi in Çukurova Üniversitesi Mühendislik Fakültesi Dergisi
- Vol. 37 (4) , 1061-1076
Open AccessElektrikli Araç Bataryalarının Bütünleşik Swara-Topsis Metodu ile Değerlendirilmesi
Küreselleşme ve dünya nüfusundaki hızlı artış birçok sorunu da beraberinde getirmektedir. Bunlardan birisi de İçten Yanmalı Motorla çalışan araçların neden olduğu ulaşım, trafik ve çevre sorunudur. Bu yüzden bilim insanları bir yandan ulaşım ve trafik sorununu çözmeye çalışırken diğer yandan yenilenebilir ve çevre dostu alternatif enerji kaynakları ile bunları kullanan araçlar üzerine yoğunlaştırmaktadır. Özellikle elektrik makinaları, bataryalar ve güç elektroniği alanlarında yaşanan teknolojik gelişmeler, girişimcileri elektrikli araç üretimine yönlendirmektedir. Elektrikli Araç çalışmalarında yaşanan ilerlemeler sayesinde batarya ile çalışan Elektrikli araçlar yavaş yavaş fosil yakıt kullanan araçların yerini almaya başlamıştır. Ancak daha iyi performans gösterecek batarya geliştirme çalışmaları devam ettiğinden elektrikli araç kullanımı yavaş, fakat hızlanarak devam etmektedir. Batarya geliştirme çalışmalarında öncelikle hızlı şarj, taşıt menzili, uzun pil ömrü, düşük maliyet, batarya kapasitesi, şarj süresi, batarya verimi ve batarya güç değeri vb. gereksinimler karşılanmaya çalışılmaktadır. Bu noktada Lityum-İyon bataryalar ön plana çıkmaktadır. Ancak geliştirilen Lityum-İyon batarya çeşitlerinin değişik performans özellikleri, Elektrikli Araç üreticilerinin batarya seçiminde karar vermelerini zorlaştırmaktadır. Bu çalışmada Çok Kriterli Karar Verme yöntemlerinden Adım Adım Ağırlık Değerlendirme Oran Analizi ve İdeal Çözüme Benzerliğe Göre Tercih Sıralama kullanılarak, karar vericilere Lityum-İyon batarya seçiminde yardımcı olacak bir model önerilmiştir. Böylece Elektrikli Araç üretim çalışmalarında yer alan işletmelere en uygun bataryayı seçme, elektrikli araçların maliyetini azaltma ve performanslarını artırma çalışmalarında faydalı olunması öngörülmektedir.
- Open Access
- 12 December 2022
- Published by El-Cezeri: Journal of Science and Engineering in El-Cezeri Fen ve Mühendislik Dergisi
Numerical Investigation of Cooling an Industrial Roller by Using Swirling Jets
Effective cooling of industrial rollers has prime importance to prevent the quality degradation of the system and product. High temperature difference on the roller surface may result in thermal stresses and can cause deformations on roller surface and product. In order to prevent these deformations, cooling of an industrial roller by using swirling jets is investigated for different parameters numerically in this study. Effects of Reynolds number, surface heat flux and variation in inlet temperature of the fluid on the performance of an industrial roller are investigated in terms of temperature difference between inner and outer surface of the roller. ANSYS Fluent CFD program is used to simulate heat transfer and fluid flow in this numerical study. As a result, it is obtained that increasing Re number from 1000 to 1700 causes a decrease of 45.4% in the temperature difference between inner and outer surface of the roller. Increasing surface heat flux from 5000 to 12500 W/m2 has resulted in an increase of 149.4% in difference between inner and outer surface temperature. Increasing coolant fluid inlet temperature from 5 to 20°C has resulted in an increase of surface temperature but there is no significant change in heat transfer characteristics of the system. It is evaluated that the results of this study will contribute to design more effective cooled industrial roller.
- 12 December 2022
- Published by El-Cezeri: Journal of Science and Engineering in El-Cezeri Fen ve Mühendislik Dergisi
Open AccessNumerical Investigation of Cooling an Industrial Roller by Using Swirling Jets
Effective cooling of industrial rollers has prime importance to prevent the quality degradation of the system and product. High temperature difference on the roller surface may result in thermal stresses and can cause deformations on roller surface and product. In order to prevent these deformations, cooling of an industrial roller by using swirling jets is investigated for different parameters numerically in this study. Effects of Reynolds number, surface heat flux and variation in inlet temperature of the fluid on the performance of an industrial roller are investigated in terms of temperature difference between inner and outer surface of the roller. ANSYS Fluent CFD program is used to simulate heat transfer and fluid flow in this numerical study. As a result, it is obtained that increasing Re number from 1000 to 1700 causes a decrease of 45.4% in the temperature difference between inner and outer surface of the roller. Increasing surface heat flux from 5000 to 12500 W/m2 has resulted in an increase of 149.4% in difference between inner and outer surface temperature. Increasing coolant fluid inlet temperature from 5 to 20°C has resulted in an increase of surface temperature but there is no significant change in heat transfer characteristics of the system. It is evaluated that the results of this study will contribute to design more effective cooled industrial roller.