FKFares Kanouni

Fares Kanouni

*This is an algorithmically generated author record based on publicly available information.

Fares Kanouni has a total of 19 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Measurement of the electrical conductivity of aqueous metal chloride solutions using a phononic crystal sensor

    by Fares Kanouni, Mosbah Daamouche, Ahmed Mehaney, Mahdi Rahmani, Bouras Ilyas, Hussein A Elsayed, Bahram Djafari-Rouhani

    This work proposes a novel approach for the measurement of electrical conductivity in aqueous solutions of transition metal chlorides, specifically CuCl 2 –water, FeCl 3 –water, and NiCl 2 –water using a phononic–fluidic sensor. Indeed, it establishes a direct correlation between conductivity and the frequency of a cavity mode in the phononic crystal as a function of concentration. The phononic structure consists of air holes periodically distributed in a stainless-steel matrix. Meanwhile, the designed phononic crystal structure possesses a wide phononic band gap of width of 145 kHz that could be of a distinct effect through the detection process. By introducing a transition metal chlorides as defect in the central hole of the phononic crystal, the emergence of a resonant mode is expected which in turn represents the mainstay towards the detection of metal chlorides. In this regard, our findings investigated a significant shift in the spectral position of the resonant frequency with the concentration’s changes of metal chlorides, providing a superb sensitivity with respect to the concentration of 1.88 × 10 −4 (kHz ppm −1 ) for FeCl 3 solution, 1.80 × 10 −4 (kHz ppm −1 ) for NiCl 2 and 0.83 × 10 −4 (kHz ppm −1 ) for CuCl 2 . In addition, the highest figure of merit and quality factor values are obtained for FeCl 3 , which are 767.28 × 10 −7 ppm −1 and 162.75, respectively. Moreover, the lowest detection limits of the proposed sensor are 0.024 ppm for FeCl 3 , 0.039 ppm for NiCl 2 , and 0.061 ppm for CuCl 2 . In parallel, we performed direct electrical conductivity measurements for the same concentrations. A clear and consistent correlation between the resonant frequency and the electrical conductivity was observed. Based on this correlation, a calibration curve was established, enabling the indirect estimation of electrical conductivity from resonant frequency data. The sensor sensitivity with respect to electrical conductivity was found to be 0.1889 kHz (mS −1 cm −1 ) for FeCl 3 , 0.2056 kHz (mS −1 cm −1 ) for NiCl 2 , and 0.1548 kHz (mS −1 cm −1 ) for CuCl 2 .

  • The Piezoelectricity of AlScN Thin Films under High-Pressure Regime

    by Fares Kanouni, Fahima Arab, Saad Amara, Khaled Bouamama, Mohamed Halit

    This study investigated the structural, mechanical, piezoelectric, and electromechanical properties of AlScN thin films using density functional theory (DFT) under varying levels of applied pressure, ranging from 0 to 20 GPa. The primary focus of this research is to explore the feasibility of optimizing AlScN thin films for surface acoustic wave (SAW) applications through pressure-induced modifications. Our findings reveal two significant outcomes. First, we observe a notable increase in the elastic constant C33 as a function of pressure. This increase signifies a substantial enhancement in material stiffness, directly influencing wave propagation and velocity within the thin films. Second, a remarkable 68% improvement in the piezoelectric constant, d33, is identified for Al0.75Sc0.25N at an applied pressure of 20 GPa compared to Al0.75Sc0.25N at 0 GPa. This enhancement has a profound impact on the electromechanical coupling characteristics of the material. These results underscore the potential for tuning the piezoelectric response of AlScN thin films using applied pressure, offering a promising avenue for enhancing the performance of SAW-based AlScN devices.


  • Open Access

    Electro-Acoustic Properties of Scandium-Doped Aluminum Nitride (ScxAl1-xN) Material and its Application to Phononic Crystal-Coupled SAW Devices

    by Fahima Arab, Fares Kanouni, Rafik Serhane, Yan Pennec, Zafer Özer, Khaled Bouamama

    Within the framework of the Density Functional Theory, the elastic, dielectric, and piezoelectric coefficients of w-ScxAl1−xN material were investigated for scandium (Sc) concentrations x = 0 to 0.375. The electro-acoustic properties are used to investigate the frequency response of the SAW delay line, based on the tilt θ° of the normal c-axis of the w-ScxAl1−xN piezoelectric thin film. We found that the piezoelectric response is improved as the Sc concentration increases, which is consistent with existing works in the literature. A 2D-phononic crystal pillars was then grafted on top of the surface, and the dependence of the acoustic band gaps is investigated with the help of the finite element method as a function of the Sc concentration and the tilted angle of w-Sc0.375Al0.625N. It was found that the two first band gaps exhibit a shift toward low frequencies with increasing Sc concentration. Moreover, the second acoustic bandgap is more sensitive to the inclination angle than the first. Furthermore, the insertion loss (S21) of w-Sc0.375Al0.625N is improved by 22 dB at θ° = 60°. The c-axis tilted Sc0.375Al0.625N-SAW delay line coupled with 2D-phononic crystals is a promising structure for low-loss and high-frequency SAW devices.


  • TiO2/ZnO PHOTONIC CRYSTAL PREPARED BY SPRAY PYROLYSIS METHOD: APPLICATION TO MULTICHANNEL FILTER

    by F. Kanouni, S. Amara, A. Assali, F. Arab, Q. Zou

    Single-layer titanium dioxide (TiO2, ZnO, double-layer TiO2/ZnO and multilayer TiO2/ZnO/TiO2/ZnO were grown on ordinary glass substrate by ultrasonic spray deposition at 300∘C. Titanium chloride, zinc acetate and deionized water were employed as precursors. The ultraviolet–visible spectrometer spectra show that the quality of optical transmittance in visible wavelength range decreases as the number of bilayers increases. The crystalline phase of the thin films was identified through X-ray diffraction method with diffraction patterns scan used at 2[ ] from 10∘ to 90∘. From the DRX results, it is found that the crystallinity is enhanced when the number of TiO2/ZnO layers increased. From the 2D/3D atomic force microscopy (AFM) analysis, it is found that the surface of the films was covered by triangle-like particles. However, bilayer and multilayer TiO2/ZnO thin films show smooth and compacted surface roughnesses compared to single-layer TiO2 and ZnO, respectively. In addition to this experimental work, a multichannel filter based on TiO2/ZnO subphotonic crystals is suggested. The transmission properties of this filter have been investigated by means of the transfer-matrix method (TMM). The idea is to import a wedge of air with an apex angle as the defect layer to disturb the original periodicity of the oxide photonic crystal and generate some new kind of multichannel filtering properties.