Javier Onõro
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Javier Onõro has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
- Danieli Aparecida Pereira Reis
Universidade Federal de Sao Paulo, Brasil
5 shared publications - Adriano Gonçalves dos Reis
Universidade Estadual Paulista, Brasil
3 shared publications C. Ranninger
3 shared publicationsCarlos de Moura Neto
3 shared publications- Miguel Justino Ribeiro Barboza
Universidade de São Paulo, Brasil
3 shared publications J. A. Gutiérrez-Vázquez
2 shared publications
Latest Publications
- 8 December 2023
- Published by Springer Nature in Journal of Failure Analysis and Prevention
- Vol. 24 (1) , 172-178
Failure Analysis of Aluminum Brass Condenser Tubes due to Dezincification
- 8 December 2023
- Published by Springer Nature in Journal of Failure Analysis and Prevention
- Vol. 24 (1) , 172-178
Failure Analysis of Aluminum Brass Condenser Tubes due to Dezincification
- Open Access
The Influence of Laser Nitriding on Creep Behavior of Ti-4Al-4V Alloy with Widmanstätten Microstructure
Ti-6Al-4V alloy has been considered in applications of aeronautical and aerospace industries, due to its properties such as high specific resistance, good creep resistance and metallurgical stability. However, its use in applications for high temperatures is restricted due to its great affinity with the oxygen, which results in the formation of oxide layers and limits its mechanical resistance at these conditions. Thus, specific treatments have been employed in the material to work as surface barriers to avoid the oxygen diffusion in the alloy under high temperature conditions. One surface treatment that can be used is laser nitriding. In the present work, the surface of Ti-6Al-4V alloy with Widmanstätten microstructure was nitrided by applying Nd:YAG laser focal with 0.6 mm diameter, at laser power of 700, 750 and 800 W, process speed of 100 mm/s and 20 L/min of N2 flow. Creep tests were performed at constant load at 600 °C and 125 MPa, to verify the influence of treatment on the Ti-6Al-4V alloy. Results have indicated a lower stationary creep rate for the titanium alloy with Widmanstätten laser-nitrided structure when compared to the non-nitriding material. Besides that, the surface hardness increased from 368 HV of base material to 1000 HV after laser nitriding.
Open AccessThe Influence of Laser Nitriding on Creep Behavior of Ti-4Al-4V Alloy with Widmanstätten Microstructure
Ti-6Al-4V alloy has been considered in applications of aeronautical and aerospace industries, due to its properties such as high specific resistance, good creep resistance and metallurgical stability. However, its use in applications for high temperatures is restricted due to its great affinity with the oxygen, which results in the formation of oxide layers and limits its mechanical resistance at these conditions. Thus, specific treatments have been employed in the material to work as surface barriers to avoid the oxygen diffusion in the alloy under high temperature conditions. One surface treatment that can be used is laser nitriding. In the present work, the surface of Ti-6Al-4V alloy with Widmanstätten microstructure was nitrided by applying Nd:YAG laser focal with 0.6 mm diameter, at laser power of 700, 750 and 800 W, process speed of 100 mm/s and 20 L/min of N2 flow. Creep tests were performed at constant load at 600 °C and 125 MPa, to verify the influence of treatment on the Ti-6Al-4V alloy. Results have indicated a lower stationary creep rate for the titanium alloy with Widmanstätten laser-nitrided structure when compared to the non-nitriding material. Besides that, the surface hardness increased from 368 HV of base material to 1000 HV after laser nitriding.
- 1 August 2013
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 577, 48-53
Creep behavior and surface characterization of a laser surface nitrided Ti–6Al–4V alloy
- 1 August 2013
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 577, 48-53
Creep behavior and surface characterization of a laser surface nitrided Ti–6Al–4V alloy
- Open Access
- 1 January 2013
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 2 (1) , 48-51
Creep behavior study at 500°C of laser nitrided Ti-6Al-4V alloy
- 1 January 2013
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 2 (1) , 48-51
Open AccessCreep behavior study at 500°C of laser nitrided Ti-6Al-4V alloy
- 16 July 2011
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 42 (10) , 3031-3034
Influence of Laser Treatment on the Creep of the Ti-6Al-4V Alloy
- 16 July 2011
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 42 (10) , 3031-3034
Influence of Laser Treatment on the Creep of the Ti-6Al-4V Alloy
- Open Access
- 26 March 2011
- Published by Wiley in Rare Metals
- Vol. 30 (2) , 200-205
High‐temperature mechanical properties of aluminium alloys reinforced with titanium diboride (TiB 2 ) particles
The physical and mechanical properties of metal matrix composites were improved by the addition of reinforcements. The mechanical properties of particulate‐reinforced metal‐matrix composites based on aluminium alloys (6061 and 7015) at high temperatures were studied. Titanium diboride (TiB 2 ) particles were used as the reinforcement. All the composites were produced by hot extrusion. The tensile properties and fracture characteristics of these materials were investigated at room temperature and at high temperatures to determine their ultimate strength and strain to failure. The fracture surface was analysed by scanning electron microscopy. TiB 2 particles provide high stability of the aluminium alloys (6061 and 7015) in the fabrication process. An improvement in the mechanical behaviour was achieved by adding TiB 2 particles as reinforcement in both the aluminium alloys. Adding TiB 2 particles reduces the ductility of the aluminium alloys but does not change the microscopic mode of failure, and the fracture surface exhibits a ductile appearance with dimples formed by coalescence.
- 26 March 2011
- Published by Wiley in Rare Metals
- Vol. 30 (2) , 200-205
Open AccessHigh‐temperature mechanical properties of aluminium alloys reinforced with titanium diboride (TiB 2 ) particles
The physical and mechanical properties of metal matrix composites were improved by the addition of reinforcements. The mechanical properties of particulate‐reinforced metal‐matrix composites based on aluminium alloys (6061 and 7015) at high temperatures were studied. Titanium diboride (TiB 2 ) particles were used as the reinforcement. All the composites were produced by hot extrusion. The tensile properties and fracture characteristics of these materials were investigated at room temperature and at high temperatures to determine their ultimate strength and strain to failure. The fracture surface was analysed by scanning electron microscopy. TiB 2 particles provide high stability of the aluminium alloys (6061 and 7015) in the fabrication process. An improvement in the mechanical behaviour was achieved by adding TiB 2 particles as reinforcement in both the aluminium alloys. Adding TiB 2 particles reduces the ductility of the aluminium alloys but does not change the microscopic mode of failure, and the fracture surface exhibits a ductile appearance with dimples formed by coalescence.
- 1 October 2010
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 660-661, 229-234
Comparation between Pulsed Nd:YAG Laser Superficial Treatment and Ceramic Coating in Creep Test of Ti-6-4V Alloy
The objective of this work was evaluating the creep resistance of the Ti-6Al-4V alloy with superficial treatment of pulsed Nd:YAG laser and ceramic coating in creep test of Ti-6Al-4V alloy. It was used Ti-6Al-4V alloy as cylindrical bars under forged and annealing of 190oC by 6 hours condition and cooled by air. The Ti-6Al-4V alloy after the superficial treatment of pulsed Nd:YAG laser and ceramic coating was submitted to creep tests at 600°C and 125 at 319 MPa, under constant load mode. In the Nd:YAG pulsed laser treatment was used an environment of 40 % N and 60 % Ar, with 2.1 W of power and 10 m/s of speed. Yttria (8 wt.%) stabilized zirconia (YSZ) with a CoNiCrAlY bond coat was atmospherically plasma sprayed on Ti-6Al-4V substrates by Sulzer Metco Type 9 MB. The obtained results suggest the laser treatment on Ti-6Al-4V alloy improved its creep resistance.
- 1 October 2010
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 660-661, 229-234
Comparation between Pulsed Nd:YAG Laser Superficial Treatment and Ceramic Coating in Creep Test of Ti-6-4V Alloy
The objective of this work was evaluating the creep resistance of the Ti-6Al-4V alloy with superficial treatment of pulsed Nd:YAG laser and ceramic coating in creep test of Ti-6Al-4V alloy. It was used Ti-6Al-4V alloy as cylindrical bars under forged and annealing of 190oC by 6 hours condition and cooled by air. The Ti-6Al-4V alloy after the superficial treatment of pulsed Nd:YAG laser and ceramic coating was submitted to creep tests at 600°C and 125 at 319 MPa, under constant load mode. In the Nd:YAG pulsed laser treatment was used an environment of 40 % N and 60 % Ar, with 2.1 W of power and 10 m/s of speed. Yttria (8 wt.%) stabilized zirconia (YSZ) with a CoNiCrAlY bond coat was atmospherically plasma sprayed on Ti-6Al-4V substrates by Sulzer Metco Type 9 MB. The obtained results suggest the laser treatment on Ti-6Al-4V alloy improved its creep resistance.
- Open Access
- 30 June 2010
- Published by Editorial CSIC in Revista de Metalurgia
- Vol. 46 (3) , 274-284
Fabricación y comportamiento de espumas de aluminio con diferente densidad a partir de un precursor AlSi12
Se han fabricado espumas de aluminio de poro cerrado, de tres diferentes rangos de densidad, utilizando un precursor AlSi12 producido por pulvimetalurgia. El objetivo ha sido determinar el efecto que tiene la densidad de estos materiales respecto a su comportamiento mecánico. El precursor utilizado contenía un 0,4 % de hidruro de titanio (TiH2) como agente espumante, mezclado con aluminio y silicio en cantidades adecuadas para lograr la composición comercial del precursor AlSi12. Una vez cortadas las muestras, se efectuaron tratamientos térmicos de espumación entre 630 y 750 °C, a tiempos de espumación variables entre 3 y 20 min. Se determinaron las mejores condiciones de solidificación para evitar el colapso mediante aire forzado. Las muestras se prepararon con el mismo peso a diferentes densidades, habiéndose obtenido, que el mejor comportamiento mecánico se lograba en las espumas de mayor densidad, comprendidas entre 0,70 y 0,81 g/cm3.
- 30 June 2010
- Published by Editorial CSIC in Revista de Metalurgia
- Vol. 46 (3) , 274-284
Open AccessFabricación y comportamiento de espumas de aluminio con diferente densidad a partir de un precursor AlSi12
Se han fabricado espumas de aluminio de poro cerrado, de tres diferentes rangos de densidad, utilizando un precursor AlSi12 producido por pulvimetalurgia. El objetivo ha sido determinar el efecto que tiene la densidad de estos materiales respecto a su comportamiento mecánico. El precursor utilizado contenía un 0,4 % de hidruro de titanio (TiH2) como agente espumante, mezclado con aluminio y silicio en cantidades adecuadas para lograr la composición comercial del precursor AlSi12. Una vez cortadas las muestras, se efectuaron tratamientos térmicos de espumación entre 630 y 750 °C, a tiempos de espumación variables entre 3 y 20 min. Se determinaron las mejores condiciones de solidificación para evitar el colapso mediante aire forzado. Las muestras se prepararon con el mismo peso a diferentes densidades, habiéndose obtenido, que el mejor comportamiento mecánico se lograba en las espumas de mayor densidad, comprendidas entre 0,70 y 0,81 g/cm3.
- Open Access
- 9 February 2010
- Published by Wiley in Materials and Corrosion
- Vol. 61 (2) , 125-129
The stress corrosion cracking behaviour of heat‐treated Al–Zn–Mg–Cu alloy in modified salt spray fog testing
The stress corrosion cracking behaviour of 7075 (Al–Zn–Mg–Cu) alloy have been studied in a salt spray fog chamber with two vapourised aqueous solutions (0 and 5% NaCl). The paper analyses the stress corrosion resistance of 7075 aluminium alloy with several precipitation‐ageing heat treatments. The results are compared with that obtained in 3.5% NaCl aqueous solution at 20 °C. The salt spray fog testing has permitted a good evaluation of SCC susceptibility in 7075 alloy. All temper conditions studied were susceptible to SCC in the different environments tested. 7075‐T6 temper was the most susceptible, while in all the cases studied 7075‐T73 temper was the least susceptible. Compared to 7075‐T6, 7075‐RRA temper improved the resistance against the SCC process, but the mechanical properties obtained were lower.
- 9 February 2010
- Published by Wiley in Materials and Corrosion
- Vol. 61 (2) , 125-129
Open AccessThe stress corrosion cracking behaviour of heat‐treated Al–Zn–Mg–Cu alloy in modified salt spray fog testing
The stress corrosion cracking behaviour of 7075 (Al–Zn–Mg–Cu) alloy have been studied in a salt spray fog chamber with two vapourised aqueous solutions (0 and 5% NaCl). The paper analyses the stress corrosion resistance of 7075 aluminium alloy with several precipitation‐ageing heat treatments. The results are compared with that obtained in 3.5% NaCl aqueous solution at 20 °C. The salt spray fog testing has permitted a good evaluation of SCC susceptibility in 7075 alloy. All temper conditions studied were susceptible to SCC in the different environments tested. 7075‐T6 temper was the most susceptible, while in all the cases studied 7075‐T73 temper was the least susceptible. Compared to 7075‐T6, 7075‐RRA temper improved the resistance against the SCC process, but the mechanical properties obtained were lower.
- 1 October 2009
- Published by Elsevier in International Journal of Pressure Vessels and Piping
- Vol. 86 (10) , 656-660
Corrosion fatigue behaviour of 317LN austenitic stainless steel in phosphoric acid
- 1 October 2009
- Published by Elsevier in International Journal of Pressure Vessels and Piping
- Vol. 86 (10) , 656-660
Corrosion fatigue behaviour of 317LN austenitic stainless steel in phosphoric acid