Kew-Ho Lee
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Kew-Ho Lee has a total of 29 co-authors. Here are the top co-authors by number of shared publications:
Dong-Wook Lee
Advanced Materials Division, Center for Membranes, Korea Research Institute of Chemical Technology, Daejeon, Republic of Korea
7 shared publications- Saira Bano
Advanced Materials Division, Center for Membranes Korea Research Institute of Chemical Technology Yuseong‐Gu Daejeon 305‐606 Republic of Korea
5 shared publications Sang‐Gyun Kim
Membrnae and Separation Research Center, Korea Research Institute of Chemical Technology, P.O. Box 107, Yuseong‐gu, Daejeon 305‐606, S. Korea
5 shared publications- Asif Mahmood
Department of Chemical Engineering, Pakistan Institute of Engineering and Applied Science, Islamabad, Pakistan
4 shared publications Chang-Yeol Yu
4 shared publicationsSeong-Joong Kim
Advanced Materials Division, Center for Membranes, Korea Research Institute of Chemical Technology, Daejeon, Republic of Korea
3 shared publications
Latest Publications
- 1 April 2019
- Vol. 5 (2) , 89
Korea- Italy Workshop on Membranes: A Long Relationship and Friendship between Korea and Italy
- 1 April 2019
- Vol. 5 (2) , 89
Korea- Italy Workshop on Membranes: A Long Relationship and Friendship between Korea and Italy
- 31 August 2016
- Published by Springer Nature
- p. 723-727
Ethanol–Water Mixtures: Separation by Pervaporation
- 31 August 2016
- Published by Springer Nature
- p. 723-727
Ethanol–Water Mixtures: Separation by Pervaporation
- 31 August 2016
- Published by Springer Nature
- p. 1474-1476
Pd–Cu Alloys for Hydrogen Separations
- 17 June 2016
- Published by Taylor & Francis in Separation Science and Technology
- Vol. 51 (12) , 2062-2069
DME conversion using high flux tubular membrane reactors
High flux tubular membrane reactors were designed for dimethyl ether (DME) steam reforming. Considering the facile scale-up and high flux of hydrogen, tubular stainless steel supports were employed for the membrane reactors. At 500°C, DME conversion reached ~100%, while hydrogen recovery reached 20%. However, contamination by CO was rather high (>1%), making this process unsuitable for proton exchange membrane fuel cell applications, which require a CO concentration of <100 ppm. This result showed that an additional polishing step was needed to reduce the CO concentration. Membrane reactors were further modified to perform an water–gas shift reaction on the permeate of the membrane reactors by employing a fixed bed reactor, which yielded high-purity hydrogen (~99%) along with a low CO content (<20 ppm).
- 17 June 2016
- Published by Taylor & Francis in Separation Science and Technology
- Vol. 51 (12) , 2062-2069
DME conversion using high flux tubular membrane reactors
High flux tubular membrane reactors were designed for dimethyl ether (DME) steam reforming. Considering the facile scale-up and high flux of hydrogen, tubular stainless steel supports were employed for the membrane reactors. At 500°C, DME conversion reached ~100%, while hydrogen recovery reached 20%. However, contamination by CO was rather high (>1%), making this process unsuitable for proton exchange membrane fuel cell applications, which require a CO concentration of <100 ppm. This result showed that an additional polishing step was needed to reduce the CO concentration. Membrane reactors were further modified to perform an water–gas shift reaction on the permeate of the membrane reactors by employing a fixed bed reactor, which yielded high-purity hydrogen (~99%) along with a low CO content (<20 ppm).
- 18 January 2016
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 133 (18)
Effective incorporation of TiO2 nanoparticles into polyamide thin‐film composite membranes
The effectiveness of TiO2 nanoparticles in improving the performance of polyamide (PA) thin‐film composite (TFC) membranes has been investigated. PA TFC membranes were prepared by interfacial polymerization with m‐phenylenediamine (MPD) and 1,3,5‐benzene tricarbonyl trichloride (TMC) where TiO2 particles were added during and after interfacial polymerization. To distribute the TiO2 nanoparticles uniformly in the PA films, colloidally stable TiO2 sols were synthesized and added to the aqueous MPD solution rather than to an organic TMC solution. Through the use of different incorporation methods, TiO2 particles were located on the top surface, in PA film layer, and in both positions. In the case of dense PA layers, the hydrophilicity of the membranes was significantly improved due to the presence of TiO2 particles, resulting in an increased water flux. On the other hand, the enhancement of water flux was less significant when TiO2 particles were incorporated into a loose PA film that was prepared with additives. In addition, a BSA fouling test confirmed that TiO2 nanoparticles effectively improve the antifouling properties of the membranes for both dense and loose PA films. This effect is possibly due to increased hydrophilicity, covering of the fouling space, and a reduction in surface roughness. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016, 133, 43383.
- 18 January 2016
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 133 (18)
Effective incorporation of TiO2 nanoparticles into polyamide thin‐film composite membranes
The effectiveness of TiO2 nanoparticles in improving the performance of polyamide (PA) thin‐film composite (TFC) membranes has been investigated. PA TFC membranes were prepared by interfacial polymerization with m‐phenylenediamine (MPD) and 1,3,5‐benzene tricarbonyl trichloride (TMC) where TiO2 particles were added during and after interfacial polymerization. To distribute the TiO2 nanoparticles uniformly in the PA films, colloidally stable TiO2 sols were synthesized and added to the aqueous MPD solution rather than to an organic TMC solution. Through the use of different incorporation methods, TiO2 particles were located on the top surface, in PA film layer, and in both positions. In the case of dense PA layers, the hydrophilicity of the membranes was significantly improved due to the presence of TiO2 particles, resulting in an increased water flux. On the other hand, the enhancement of water flux was less significant when TiO2 particles were incorporated into a loose PA film that was prepared with additives. In addition, a BSA fouling test confirmed that TiO2 nanoparticles effectively improve the antifouling properties of the membranes for both dense and loose PA films. This effect is possibly due to increased hydrophilicity, covering of the fouling space, and a reduction in surface roughness. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016, 133, 43383.
- 10 December 2015
- Published by Springer Nature
- p. 1-2
Open AccessPd–Cu Alloys for Hydrogen Separations
- 1 January 2015
- Published by Elsevier in Journal of Membrane Science
- Vol. 473, 8-15
Effect of operating conditions on the performance of solid electrolyte membrane reactor for steam and CO2 electrolysis
- 1 January 2015
- Published by Elsevier in Journal of Membrane Science
- Vol. 473, 8-15
Effect of operating conditions on the performance of solid electrolyte membrane reactor for steam and CO2 electrolysis
- Top Cited Papers
- 9 December 2014
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 3 (5) , 2065-2071
Graphene oxide modified polyamide nanofiltration membrane with improved flux and antifouling properties
Conceptual visualization of GO effect on fouling.
- 9 December 2014
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 3 (5) , 2065-2071
Top Cited PapersGraphene oxide modified polyamide nanofiltration membrane with improved flux and antifouling properties
Conceptual visualization of GO effect on fouling.