Yue Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Yue Wang has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
Dejun Yan
Guangdong Key Laboratory of Enterprise Advanced Welding Technology for Ships, CSSC Huangpu Wenchong Shipbuilding Company Limited, Guangzhou, People’s Republic of China
3 shared publicationsPeng Chai
3 shared publications- Peng Chai
Beihang University
3 shared publications - Shude Ji
College of Aerospace Engineering, Shenyang Aerospace University, Shenyang 110136, China
3 shared publications - He Ma
Beihang University
2 shared publications - Yanhua Zhang
School of Mechanical Engineering and Automation, Beihang University, Beijing, China
2 shared publications
Latest Publications
- Open Access
- 13 May 2021
- Published by Polish Academy of Sciences Chancellery in Archives of Metallurgy and Materials
- Vol. 66 (2) , 451-460
Characteristics and Tensile-Shear Properties of Refill FSSW Joint Under Different Plunge Depths in 2060 Aluminum Alloy
Refill friction stir spot welding (refill FSSW) was used to weld 3.2-mm-thick 2060 aluminum alloy. Joint formation, defect characteristics and tensile-shear property were analyzed. Results show that keyhole can be completely eliminated under different plunge depths. However, defects such as void, unconnected welding, hook can be observed under the plunge depths of 3.4-4 mm. The size of the overall void initially increased and then decreased with the increase of the plunge depth, while the void was the smallest under the plunge depth of 3.4 mm. The unconnected defect at the lap interface gradually shrank a welding line from obvious crack. Different hook morphologies were observed under different plunge depths. The tensile-shear load of joint increased with the increase of the plunge depth and was up to the largest under the plunge depth of 4 mm. All the tensile-shear specimens fractured along the lap interface. Compared with the void, the unconnected defect had a greater influence on the tensile-shear property.
- 13 May 2021
- Published by Polish Academy of Sciences Chancellery in Archives of Metallurgy and Materials
- Vol. 66 (2) , 451-460
Open AccessCharacteristics and Tensile-Shear Properties of Refill FSSW Joint Under Different Plunge Depths in 2060 Aluminum Alloy
Refill friction stir spot welding (refill FSSW) was used to weld 3.2-mm-thick 2060 aluminum alloy. Joint formation, defect characteristics and tensile-shear property were analyzed. Results show that keyhole can be completely eliminated under different plunge depths. However, defects such as void, unconnected welding, hook can be observed under the plunge depths of 3.4-4 mm. The size of the overall void initially increased and then decreased with the increase of the plunge depth, while the void was the smallest under the plunge depth of 3.4 mm. The unconnected defect at the lap interface gradually shrank a welding line from obvious crack. Different hook morphologies were observed under different plunge depths. The tensile-shear load of joint increased with the increase of the plunge depth and was up to the largest under the plunge depth of 4 mm. All the tensile-shear specimens fractured along the lap interface. Compared with the void, the unconnected defect had a greater influence on the tensile-shear property.
- 7 January 2021
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 112 (9-10) , 2573-2582
Influences of ultrasonic on friction stir welding of Al/Ti dissimilar alloys under different welding conditions
- 7 January 2021
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 112 (9-10) , 2573-2582
Influences of ultrasonic on friction stir welding of Al/Ti dissimilar alloys under different welding conditions
- 22 December 2020
- Published by Polish Academy of Sciences Chancellery in Archives of Metallurgy and Materials
- Vol. 66 (1) , 153-161
Joint Formation and Mechanical Properties of 2060 Aluminum Alloy Refill Friction Stir Spot Welding Joint
Refill friction stir spot welding (RFSSW) was used to weld the 2060 aluminum alloy with 2 mm thickness. Joint formation, defect characteristics and mechanical properties were investigated. Results show that stir zone (SZ) is clarified into dynamic recrystallization zone (DRZ) and heat extruded zone (HEZ) due to different microstructural features. The size of void near the hook tip decreases with the increase of the plunge depth. Different hook morphologies are obtained under different plunge depths. The tensile-shear load of joint with the void defect initially decreases and then increases with increasing plunge depth. The mean loads of joints under different plunge depths are in the range of 5.1-5.8 kN. The void separates the hook from lap interface, so the cracks initiating from the hook propagate along the sleeve retreating path. The hook has a larger influence on the tensile-shear load of joint than void. All the tensile specimens present a shear-plug fracture mode.
- 22 December 2020
- Published by Polish Academy of Sciences Chancellery in Archives of Metallurgy and Materials
- Vol. 66 (1) , 153-161
Joint Formation and Mechanical Properties of 2060 Aluminum Alloy Refill Friction Stir Spot Welding Joint
Refill friction stir spot welding (RFSSW) was used to weld the 2060 aluminum alloy with 2 mm thickness. Joint formation, defect characteristics and mechanical properties were investigated. Results show that stir zone (SZ) is clarified into dynamic recrystallization zone (DRZ) and heat extruded zone (HEZ) due to different microstructural features. The size of void near the hook tip decreases with the increase of the plunge depth. Different hook morphologies are obtained under different plunge depths. The tensile-shear load of joint with the void defect initially decreases and then increases with increasing plunge depth. The mean loads of joints under different plunge depths are in the range of 5.1-5.8 kN. The void separates the hook from lap interface, so the cracks initiating from the hook propagate along the sleeve retreating path. The hook has a larger influence on the tensile-shear load of joint than void. All the tensile specimens present a shear-plug fracture mode.
- 20 October 2020
- Published by Taylor & Francis in The Journal of Adhesion
- Vol. 98 (4) , 325-347
Characteristics and strength of hybrid friction stir welding and adhesive bonding lap joints for AA2024-T3 aluminium alloy
A hybrid process combining friction stir welding with adhesive bonding is used to connect AA2024-T3 aluminum alloy. The epoxy ester adhesive was evenly smeared on the sheet surface prior to welding. Regarding the function of the adhesive in different regions at the lap interface, the lap interface can be divided into a completely FSW zone (CWZ), transition zone (TZ) and completely sealed zone (CSZ). During the tensile-shear test, the load is initially shared by the CWZ and TZ. With the increase of the external load the cracks first initiate at the adhesive layer, leading to the fast decrease of load–displacement curves. When the CWZ bears the load alone, the joint recovers the load-carrying capacity and the load–displacement curves increase again until the CWZ cracks and fractures. The crack propagation process of the hybrid joint mainly includes adhesive layer cracking stage and FSW interface cracking stage. The cracking load of the adhesive layer is higher than the elastic limit load of the conventional joint, and thus the adhesive does not influence the design load. The adhesive layer on the TZ reduces the stress and makes the stress distribution uniform, and on the CSZ can block the corrosion media.
- 20 October 2020
- Published by Taylor & Francis in The Journal of Adhesion
- Vol. 98 (4) , 325-347
Characteristics and strength of hybrid friction stir welding and adhesive bonding lap joints for AA2024-T3 aluminium alloy
A hybrid process combining friction stir welding with adhesive bonding is used to connect AA2024-T3 aluminum alloy. The epoxy ester adhesive was evenly smeared on the sheet surface prior to welding. Regarding the function of the adhesive in different regions at the lap interface, the lap interface can be divided into a completely FSW zone (CWZ), transition zone (TZ) and completely sealed zone (CSZ). During the tensile-shear test, the load is initially shared by the CWZ and TZ. With the increase of the external load the cracks first initiate at the adhesive layer, leading to the fast decrease of load–displacement curves. When the CWZ bears the load alone, the joint recovers the load-carrying capacity and the load–displacement curves increase again until the CWZ cracks and fractures. The crack propagation process of the hybrid joint mainly includes adhesive layer cracking stage and FSW interface cracking stage. The cracking load of the adhesive layer is higher than the elastic limit load of the conventional joint, and thus the adhesive does not influence the design load. The adhesive layer on the TZ reduces the stress and makes the stress distribution uniform, and on the CSZ can block the corrosion media.
- 22 August 2020
- Published by Springer Nature in Welding in the World
- Vol. 64 (12) , 2033-2051
Effects of welding parameters on micro-junction structure and fracture behavior of refill friction stir spot welded joints for 2060 aluminum alloys
- 22 August 2020
- Published by Springer Nature in Welding in the World
- Vol. 64 (12) , 2033-2051
Effects of welding parameters on micro-junction structure and fracture behavior of refill friction stir spot welded joints for 2060 aluminum alloys
- 13 February 2020
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 29 (2) , 866-876
Effect of Welding Parameters on Microstructure and Mechanical Properties of Friction-Stir-Welded Al-Mg-Si Alloy
- 13 February 2020
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 29 (2) , 866-876
Effect of Welding Parameters on Microstructure and Mechanical Properties of Friction-Stir-Welded Al-Mg-Si Alloy
- 28 August 2019
- Published by Springer Nature in Journal of Materials Science
- Vol. 55 (1) , 358-374
Formation mechanism and fracture behavior in extra-filling refill friction stir spot weld for Al–Cu–Mg aluminum alloy
- 28 August 2019
- Published by Springer Nature in Journal of Materials Science
- Vol. 55 (1) , 358-374
Formation mechanism and fracture behavior in extra-filling refill friction stir spot weld for Al–Cu–Mg aluminum alloy
- 16 May 2019
- Published by Springer Nature in Metals and Materials International
- Vol. 25 (6) , 1574-1585
Effect of Rotational Speed on Microstructure and Mechanical Properties of 2060 Aluminum Alloy RFSSW Joint
- 16 May 2019
- Published by Springer Nature in Metals and Materials International
- Vol. 25 (6) , 1574-1585
Effect of Rotational Speed on Microstructure and Mechanical Properties of 2060 Aluminum Alloy RFSSW Joint
- 1 December 2018
- Published by Elsevier in Journal of Manufacturing Processes
- Vol. 36, 238-247
Fatigue properties of Ti-6Al-4V alloy friction stir welding joint obtained under rapid cooling condition
- 1 December 2018
- Published by Elsevier in Journal of Manufacturing Processes
- Vol. 36, 238-247
Fatigue properties of Ti-6Al-4V alloy friction stir welding joint obtained under rapid cooling condition
- 1 August 2018
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 27 (8) , 4308-4316
Fatigue Properties of Ti-6Al-4V Titanium Alloy Friction Stir Welding Joint
- 1 August 2018
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 27 (8) , 4308-4316
Fatigue Properties of Ti-6Al-4V Titanium Alloy Friction Stir Welding Joint