Nathan Zimmerman
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Nathan Zimmerman has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Carl-Fredrik Lindberg
Department of Automation in Energy and Environment, School of Business, Society and Engineering, Mälardalen University, Box 883, 721 23 Västerås, Sweden
3 shared publications - Konstantinos Kyprianidis
Department of Engineering Sciences, Mälardalen University, 721 23 Västerås, Sweden
3 shared publications - Agostino Gambarotta
Department of Engineering and Architecture, University of Parma, Parco Area delle Scienze 181/A, 43124 Parma, Italy
1 shared publication - Costanza Saletti
Department of Engineering for Industrial Systems and Technologies, University of Parma, Parma, Italy
1 shared publication - Cristinel Ababei
Marquette University Milwaukee Wisconsin USA
1 shared publication - Erik Dahlquist
Mälardalen University
1 shared publication
Latest Publications
- Open Access
- 28 June 2020
- Published by MDPI AG in Preprints.org
A Scale-Free Dynamic Model for District Heating Aggregated Regions
District heating networks have become widespread due to their ability to distribute thermal energy efficiently, which leads to reduced carbon emissions and improved air quality. The characteristics of these networks vary remarkably depending on the urban layout and system amplitude. Moreover, extensive data about the energy distribution and thermal capacity of different areas are seldom available. Design, optimization and control of these systems are enabled by the availability of fast and scalable models of district heating networks. This work addresses this issue by proposing a novel method to develop a scale-free model of large-scale district heating networks. Starting from coarse data available at the main substations, a physics-based model of the system aggregated regions is developed by identifying the heat capacity and heat loss coefficients. The model validation on the network of Västerås, Sweden, shows compatibility with literature data and can therefore be exploited for system design, optimization and control-oriented applications. In particular, the possibility to estimate the heat storage potential of network regions allows new smart management strategies to be investigated.
- 28 June 2020
- Published by MDPI AG in Preprints.org
Open AccessA Scale-Free Dynamic Model for District Heating Aggregated Regions
District heating networks have become widespread due to their ability to distribute thermal energy efficiently, which leads to reduced carbon emissions and improved air quality. The characteristics of these networks vary remarkably depending on the urban layout and system amplitude. Moreover, extensive data about the energy distribution and thermal capacity of different areas are seldom available. Design, optimization and control of these systems are enabled by the availability of fast and scalable models of district heating networks. This work addresses this issue by proposing a novel method to develop a scale-free model of large-scale district heating networks. Starting from coarse data available at the main substations, a physics-based model of the system aggregated regions is developed by identifying the heat capacity and heat loss coefficients. The model validation on the network of Västerås, Sweden, shows compatibility with literature data and can therefore be exploited for system design, optimization and control-oriented applications. In particular, the possibility to estimate the heat storage potential of network regions allows new smart management strategies to be investigated.
- Open Access
Achieving Lower District Heating Network Temperatures Using Feed-Forward MPC
The focus of this work is to present the feasibility of lowering the supply and return temperatures of district heating networks in order to achieve energy savings through the implementation of feed-forward model predictive control. The current level of district heating technology dictates a need for higher supply temperatures, which is not the case when considering the future outlook. In part, this can be attributed to the fact that current networks are being controlled by operator experience and outdoor temperatures. The prospects of reducing network temperatures can be evaluated by developing a dynamic model of the process which can then be used for control purposes. Two scenarios are presented in this work, to not only evaluate a controller’s performance in supplying lower network temperatures, but to also assess the boundaries of the return temperature. In Scenario 1, the historical load is used as a feed-forward signal to the controller, and in Scenario 2, a load prediction model is used as the feed-forward signal. The findings for both scenarios suggest that the new control approach can lead to a load reduction of 12.5% and 13.7% respectively for the heat being supplied to the network. With the inclusion of predictions with increased accuracy on end-user demand and feed-back, the return temperature values can be better sustained, and can lead to a decrease in supply temperatures and an increase in energy savings on the production side.
Open AccessAchieving Lower District Heating Network Temperatures Using Feed-Forward MPC
The focus of this work is to present the feasibility of lowering the supply and return temperatures of district heating networks in order to achieve energy savings through the implementation of feed-forward model predictive control. The current level of district heating technology dictates a need for higher supply temperatures, which is not the case when considering the future outlook. In part, this can be attributed to the fact that current networks are being controlled by operator experience and outdoor temperatures. The prospects of reducing network temperatures can be evaluated by developing a dynamic model of the process which can then be used for control purposes. Two scenarios are presented in this work, to not only evaluate a controller’s performance in supplying lower network temperatures, but to also assess the boundaries of the return temperature. In Scenario 1, the historical load is used as a feed-forward signal to the controller, and in Scenario 2, a load prediction model is used as the feed-forward signal. The findings for both scenarios suggest that the new control approach can lead to a load reduction of 12.5% and 13.7% respectively for the heat being supplied to the network. With the inclusion of predictions with increased accuracy on end-user demand and feed-back, the return temperature values can be better sustained, and can lead to a decrease in supply temperatures and an increase in energy savings on the production side.
- Open Access
- 19 December 2018
- Published by Linkoping University Electronic Press
- No. 142,p. 148-154
Agglomeration Detection in Circulating Fluidized Bed Boilers using Refuse Derived Fuels
Here is information on how to publish, spread your research, and search for your publications. Most of LiU's research publications are directly imported into DiVA from the Web of Science. Before registering a publication, always check if the publication is already in DiVA!
- 19 December 2018
- Published by Linkoping University Electronic Press
- No. 142,p. 148-154
Open AccessAgglomeration Detection in Circulating Fluidized Bed Boilers using Refuse Derived Fuels
Here is information on how to publish, spread your research, and search for your publications. Most of LiU's research publications are directly imported into DiVA from the Web of Science. Before registering a publication, always check if the publication is already in DiVA!
- Open Access
Waste Fuel Combustion: Dynamic Modeling and Control
The focus of this study is to present the adherent transients that accompany the combustion of waste derived fuels. This is accomplished, in large, by developing a dynamic model of the process, which can then be used for control purposes. Traditional control measures typically applied in the heat and power industry, i.e., PI (proportional-integral) controllers, might not be robust enough to handle the the accompanied transients associated with new fuels. Therefore, model predictive control is introduced as a means to achieve better combustion stability under transient conditions. The transient behavior of refuse derived fuel is addressed by developing a dynamic modeling library. Within the library, there are two models. The first is for assessing the performance of the heat exchangers to provide operational assistance for maintenance scheduling. The second model is of a circulating fluidized bed block, which includes combustion and steam (thermal) networks. The library has been validated using data from a 160 MW industrial installation located in Västerås, Sweden. The model can predict, with satisfactory accuracy, the boiler bed and riser temperatures, live steam temperature, and boiler load. This has been achieved by using process sensors for the feed-in streams. Based on this model three different control schemes are presented: a PI control scheme, model predictive control with feedforward, and model predictive control without feedforward. The model predictive control with feedforward has proven to give the best performance as it can maintain stable temperature profiles throughout the process when a measured disturbance is initiated. Furthermore, the implemented control incorporates the introduction of a soft-sensor for measuring the minimum fluidization velocity to maintain a consistent level of fluidization in the boiler for deterring bed material agglomeration.
Open AccessWaste Fuel Combustion: Dynamic Modeling and Control
The focus of this study is to present the adherent transients that accompany the combustion of waste derived fuels. This is accomplished, in large, by developing a dynamic model of the process, which can then be used for control purposes. Traditional control measures typically applied in the heat and power industry, i.e., PI (proportional-integral) controllers, might not be robust enough to handle the the accompanied transients associated with new fuels. Therefore, model predictive control is introduced as a means to achieve better combustion stability under transient conditions. The transient behavior of refuse derived fuel is addressed by developing a dynamic modeling library. Within the library, there are two models. The first is for assessing the performance of the heat exchangers to provide operational assistance for maintenance scheduling. The second model is of a circulating fluidized bed block, which includes combustion and steam (thermal) networks. The library has been validated using data from a 160 MW industrial installation located in Västerås, Sweden. The model can predict, with satisfactory accuracy, the boiler bed and riser temperatures, live steam temperature, and boiler load. This has been achieved by using process sensors for the feed-in streams. Based on this model three different control schemes are presented: a PI control scheme, model predictive control with feedforward, and model predictive control without feedforward. The model predictive control with feedforward has proven to give the best performance as it can maintain stable temperature profiles throughout the process when a measured disturbance is initiated. Furthermore, the implemented control incorporates the introduction of a soft-sensor for measuring the minimum fluidization velocity to maintain a consistent level of fluidization in the boiler for deterring bed material agglomeration.
- 12 October 2016
- Published by ASME International
On Aerial Indoor Position Control and System Integration for Quadcopters Using Lidars and Inertial Measurement Units
The main contribution of this paper is to introduce a computationally efficient iterative closest line (ICL) algorithm for determining indoor position drift of a quadcopter using minimal lidar data. In addition, we present the system-level design and implementation of a new quadcopter both as hardware and flight control algorithms. Such a platform allows us to develop and experiment new control and system optimization techniques. As an example, we discuss how the proposed ICL algorithm is used for position hold and control purposes by plugging it into the low level implementation of the flight control algorithm of the quadcopter. For testing and validation we use simulations with real world data. As part of the system-level design aspects, we present an investigation of the quadcopter power consumption. We are interested in power consumption because it is the major factor that determines the flight time of a typical quadcopter. We believe that this work is a contribution toward achieving better quadcopter design and control for indoor autonomous navigation.
- 12 October 2016
- Published by ASME International
On Aerial Indoor Position Control and System Integration for Quadcopters Using Lidars and Inertial Measurement Units
The main contribution of this paper is to introduce a computationally efficient iterative closest line (ICL) algorithm for determining indoor position drift of a quadcopter using minimal lidar data. In addition, we present the system-level design and implementation of a new quadcopter both as hardware and flight control algorithms. Such a platform allows us to develop and experiment new control and system optimization techniques. As an example, we discuss how the proposed ICL algorithm is used for position hold and control purposes by plugging it into the low level implementation of the flight control algorithm of the quadcopter. For testing and validation we use simulations with real world data. As part of the system-level design aspects, we present an investigation of the quadcopter power consumption. We are interested in power consumption because it is the major factor that determines the flight time of a typical quadcopter. We believe that this work is a contribution toward achieving better quadcopter design and control for indoor autonomous navigation.
- 1 March 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 21659400,p. 1-6
Flow batteries use potential in heavy vehicles
Although batteries have been used in personal vehicles for more than a hundred years, the cost of the technology, limitation in range, absence of sufficient recharging infrastructure and rapid development of internal combustion engines during the mid-twentieth century limited its use to very niche applications. More recently, a global need for reducing CO2 emissions from fossil fuel usage and the great developments in power systems as well as in battery technology offers electric vehicles the possibility to return to the market, not just for personal use but also for a wide variety of transportation applications. In the present paper, a feasibility study for using flow batteries in heavy vehicles, more specifically, construction equipment is presented. The authors used measured energy demand profiles for different operation conditions of a wheel loader and developed a simulation model for a vanadium redox flow battery to test the performance of this vehicle using a flow battery. Additionally, the authors did a short theoretical analysis for the potential for flow batteries in train transportation, focusing on the requirements and limitations of the technology for this application.
- 1 March 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 21659400,p. 1-6
Flow batteries use potential in heavy vehicles
Although batteries have been used in personal vehicles for more than a hundred years, the cost of the technology, limitation in range, absence of sufficient recharging infrastructure and rapid development of internal combustion engines during the mid-twentieth century limited its use to very niche applications. More recently, a global need for reducing CO2 emissions from fossil fuel usage and the great developments in power systems as well as in battery technology offers electric vehicles the possibility to return to the market, not just for personal use but also for a wide variety of transportation applications. In the present paper, a feasibility study for using flow batteries in heavy vehicles, more specifically, construction equipment is presented. The authors used measured energy demand profiles for different operation conditions of a wheel loader and developed a simulation model for a vanadium redox flow battery to test the performance of this vehicle using a flow battery. Additionally, the authors did a short theoretical analysis for the potential for flow batteries in train transportation, focusing on the requirements and limitations of the technology for this application.