Ivan Z. Indutnyi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Ivan Z. Indutnyi has a total of 55 co-authors. Here are the top co-authors by number of shared publications:
- Viktor A. Dan’kO
National Academy of Sciences of Ukraine
9 shared publications - Viktor I. Mynko
National Academy of Sciences of Ukraine
9 shared publications - Mykola V. Sopinskyy
National Academy of Sciences of Ukraine
8 shared publications - Serhii Vasylovych Mamykin
National Academy of Sciences of Ukraine
8 shared publications - Petro M. Lytvyn
V. Ye. Lashkaryov Institute of Semiconductor Physics, National Academy of Sciences of Ukraine 2 , Kyiv 03028
6 shared publications - Mariia Lukaniuk
V.E. Lashkaryov Institute of Semiconductor Physics, Nat. Acad. of Sci. of Ukraine
4 shared publications
Latest Publications
- 1 November 2026
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 35 (11) , 115010
Development of copper holographic gratings for plasmonic sensors
This paper presents the development and optimization of cost-effective plasmonic sensor chips based on copper holographic diffraction gratings. While gold is the standard material for surface plasmon resonance sensors, its high cost and integration challenges have led to the investigation of copper as a viable alternative. To address copper’s susceptibility to oxidation, we propose a passivation method involving the deposition of a thin indium (In) protective layer in a single vacuum cycle. Numerical modeling using the Rigorous Coupled Wave Analysis method was employed to determine the optimal grating relief modulation depth (the ratio of peak-to-valley depth h to grating period a, equal to 0.1) and copper thickness ( d = 80–85 nm). Experimental results demonstrate that an indium layer with a mass thickness of 3–7 nm effectively stabilizes the surface of Cu grating, preventing degradation of the surface plasmon polariton resonance for over 80 d under ambient conditions. Comparative analysis shows that the sensitivity ( S ) and Figure of Merit (FoM) of passivated copper chips are nearly identical to those of gold-based gratings, with only a minor reduction (4.3% and 7.5%, respectively). These findings highlight the potential of passivated copper gratings for high-performance, low-cost environmental and gas sensing applications.
- 1 November 2026
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 35 (11) , 115010
Development of copper holographic gratings for plasmonic sensors
This paper presents the development and optimization of cost-effective plasmonic sensor chips based on copper holographic diffraction gratings. While gold is the standard material for surface plasmon resonance sensors, its high cost and integration challenges have led to the investigation of copper as a viable alternative. To address copper’s susceptibility to oxidation, we propose a passivation method involving the deposition of a thin indium (In) protective layer in a single vacuum cycle. Numerical modeling using the Rigorous Coupled Wave Analysis method was employed to determine the optimal grating relief modulation depth (the ratio of peak-to-valley depth h to grating period a, equal to 0.1) and copper thickness ( d = 80–85 nm). Experimental results demonstrate that an indium layer with a mass thickness of 3–7 nm effectively stabilizes the surface of Cu grating, preventing degradation of the surface plasmon polariton resonance for over 80 d under ambient conditions. Comparative analysis shows that the sensitivity ( S ) and Figure of Merit (FoM) of passivated copper chips are nearly identical to those of gold-based gratings, with only a minor reduction (4.3% and 7.5%, respectively). These findings highlight the potential of passivated copper gratings for high-performance, low-cost environmental and gas sensing applications.
- Open Access
Raman Scattering Enhanced by Surface Plasmon Polaritons on Ag and Al Gratings
This paper describes the development and characterization of surface-enhanced Raman spectroscopy (SERS) substrates that employ the excitation of surface plasmon polaritons (SPPs) on periodic metal diffraction gratings to amplify the Raman signal of an analyte. The gratings were fabricated via interference photolithography on As40S40Se20 thin films. The resulting surface relief was subsequently coated with either aluminium (Al gratings) or aluminium followed by silver (Ag gratings). The ratio of the relief depth to the grating period (h/a) was optimized to maximize SPP excitation efficiency. For both types of gratings, a strong angular dependence of the Raman scattering intensity of the analyte molecule (Rhodamine 6G) was observed, which anticorrelates with the angular dependence of the specularly reflected light intensity. The enhancement factor is 2 × 102 for the aluminium grating and 1 × 103 for the silver grating. This finding suggests that aluminium-based SERS substrates may serve as a cost-effective alternative to those coated with noble metals. Although the overall amplification is significantly lower than that achieved by SERS substrates based on localized surface plasmon (LSP) excitation, the grating-based SPP substrates offer a crucial advantage for quantitative measurements due to their uniform enhancement across the entire substrate area.
Open AccessRaman Scattering Enhanced by Surface Plasmon Polaritons on Ag and Al Gratings
This paper describes the development and characterization of surface-enhanced Raman spectroscopy (SERS) substrates that employ the excitation of surface plasmon polaritons (SPPs) on periodic metal diffraction gratings to amplify the Raman signal of an analyte. The gratings were fabricated via interference photolithography on As40S40Se20 thin films. The resulting surface relief was subsequently coated with either aluminium (Al gratings) or aluminium followed by silver (Ag gratings). The ratio of the relief depth to the grating period (h/a) was optimized to maximize SPP excitation efficiency. For both types of gratings, a strong angular dependence of the Raman scattering intensity of the analyte molecule (Rhodamine 6G) was observed, which anticorrelates with the angular dependence of the specularly reflected light intensity. The enhancement factor is 2 × 102 for the aluminium grating and 1 × 103 for the silver grating. This finding suggests that aluminium-based SERS substrates may serve as a cost-effective alternative to those coated with noble metals. Although the overall amplification is significantly lower than that achieved by SERS substrates based on localized surface plasmon (LSP) excitation, the grating-based SPP substrates offer a crucial advantage for quantitative measurements due to their uniform enhancement across the entire substrate area.
- 24 January 2026
- Published by Springer Nature in Plasmonics
- Vol. 21 (2) , 2033-2040
Surface Plasmon-Polariton Study of Thermally Stimulated Diffusion of Ag in thin As2S3 Films
- 24 January 2026
- Published by Springer Nature in Plasmonics
- Vol. 21 (2) , 2033-2040
Surface Plasmon-Polariton Study of Thermally Stimulated Diffusion of Ag in thin As2S3 Films
- 22 May 2025
- Published by Elsevier in Thin Solid Films
- Vol. 824
Surface plasmon-polariton study of photoinduced diffusion in light-sensitive Ag–As2S3 thin-film structure
- 22 May 2025
- Published by Elsevier in Thin Solid Films
- Vol. 824
Surface plasmon-polariton study of photoinduced diffusion in light-sensitive Ag–As2S3 thin-film structure
- 29 November 2024
- Published by Elsevier in Journal of Non-Crystalline Solids
- Vol. 649
Kinetics of thermal and photoinduced diffusion of Ag into thin layers of chalcogenide glasses
- 29 November 2024
- Published by Elsevier in Journal of Non-Crystalline Solids
- Vol. 649
Kinetics of thermal and photoinduced diffusion of Ag into thin layers of chalcogenide glasses
- Open Access
- 25 May 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (11) , 4546
Aluminum-Based Plasmonic Photodetector for Sensing Applications
Plasmonic sensors have great potential for widespread usage. However, the prohibitive cost of noble metals restrains the wider adoption of these devices. The aim of our study is to develop a cost-effective Al-based alternative to common noble metal-based plasmonic detectors. We considered a structure consisting of an n-type doped Si wafer with a shallow p-n junction and an overlying Al grating with a trapezoidal groove profile. The RCWA (rigorous coupled-wave analysis) method was used to numerically calculate the distribution of absorbed light energy in the plasmonic detector layers and to optimize the grating parameters. Based on the simulation results, experimental samples of plasmonic photodetectors with optimal grating parameters (period—633 nm, relief depth—50 nm, groove filling factor—0.36, and thickness of the intermediate Al layer—14 nm) were manufactured, and their properties were studied. For these samples, we obtained a polarization sensitivity value of Ip/Is = 8, an FWHM of the resonance in the photocurrent spectrum ranging from 50 to 100 nm, a sensitivity at the resonance maximum of Iph = 0.04–0.06 A/W, and an angular half-width of photocurrent resonance of Δθ = 5°, which are comparable to noble metal-based analogs. Our results may be used for creating cost-effective high-sensitivity plasmonic sensors.
- 25 May 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (11) , 4546
Open AccessAluminum-Based Plasmonic Photodetector for Sensing Applications
Plasmonic sensors have great potential for widespread usage. However, the prohibitive cost of noble metals restrains the wider adoption of these devices. The aim of our study is to develop a cost-effective Al-based alternative to common noble metal-based plasmonic detectors. We considered a structure consisting of an n-type doped Si wafer with a shallow p-n junction and an overlying Al grating with a trapezoidal groove profile. The RCWA (rigorous coupled-wave analysis) method was used to numerically calculate the distribution of absorbed light energy in the plasmonic detector layers and to optimize the grating parameters. Based on the simulation results, experimental samples of plasmonic photodetectors with optimal grating parameters (period—633 nm, relief depth—50 nm, groove filling factor—0.36, and thickness of the intermediate Al layer—14 nm) were manufactured, and their properties were studied. For these samples, we obtained a polarization sensitivity value of Ip/Is = 8, an FWHM of the resonance in the photocurrent spectrum ranging from 50 to 100 nm, a sensitivity at the resonance maximum of Iph = 0.04–0.06 A/W, and an angular half-width of photocurrent resonance of Δθ = 5°, which are comparable to noble metal-based analogs. Our results may be used for creating cost-effective high-sensitivity plasmonic sensors.
- Open Access
- 25 April 2024
- Published by MDPI AG in Preprints.org
Aluminum-Based Plasmonic Photodetector for Sensing Applications
Plasmonic sensors have great potential for widespread usage, but the prohibitive cost of noble metals restrains the wider adoption of this technology. The aim of our study is to develop a cost-effective Al-based alternative to plasmonic detectors commonly based on noble metals. We considered a structure that consists of a Si p-n junction with an overlying grating-relief aluminum layer. The investigation of the infrared plasmonic resonance dependency on the structure geometric parameters and optimization of the fabrication process allowed us to determine optimal parameters for photodetection enhancement. The resonance photoresponse of optimized aluminum-based plasmon-polariton photodetector was significantly improved and became comparable to noble metal-based analogs. Our results can be used for the creation of cost-effective high-sensitivity plasmonic sensors.
- 25 April 2024
- Published by MDPI AG in Preprints.org
Open AccessAluminum-Based Plasmonic Photodetector for Sensing Applications
Plasmonic sensors have great potential for widespread usage, but the prohibitive cost of noble metals restrains the wider adoption of this technology. The aim of our study is to develop a cost-effective Al-based alternative to plasmonic detectors commonly based on noble metals. We considered a structure that consists of a Si p-n junction with an overlying grating-relief aluminum layer. The investigation of the infrared plasmonic resonance dependency on the structure geometric parameters and optimization of the fabrication process allowed us to determine optimal parameters for photodetection enhancement. The resonance photoresponse of optimized aluminum-based plasmon-polariton photodetector was significantly improved and became comparable to noble metal-based analogs. Our results can be used for the creation of cost-effective high-sensitivity plasmonic sensors.
- 21 December 2023
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Optoelektronìka ta napìvprovìdnikova tehnìka
- Vol. 58, 158-166
INFLUENCE OF Se THIN FILMS ON THE EXCITATION EFFICIENCY OF SURFACE PLASMON POLARITONS IN SILVER AND ALUMINUM HOLOGRAPHIC GRATINGS
In this paper, we study the effect of thin selenium layers up to 3 nm thick on the efficiency of excitation of surface plasmon polaritons (SPPs). The Se layers were deposited by thermal evaporation in vacuum on the surface of silver and aluminum gratings. Gratings with a groove profile close to sinusoidal and a period equal to а = 694 nm were formed on chalcogenide photoresist films using interference lithography. Then they were coated with layers of the above metals with a thickness of 80–85 nm using thermal evaporation. Registration of SPP excitation on the gratings was carried out by measuring the angular dependences of the intensity of specularly reflected or diffracted p-polarized He-Ne laser radiation on a stand mounted on the basis of a G5M goniometer and a Fedorov table. An atomic force microscope was used to determine the shape of the groove profile and the depth of the grating relief. It has been found that for silver gratings with a relief modulation depth h/a less than the optimal value (which ensures maximum plasmon absorption, i.e., the maximum efficiency of SPP excitation), selenium deposition causes significant degradation of the plasmon resonance: a decrease in the depth of the minimum of the total reflection Rpt (i.e., a decrease in the efficiency of plasmon absorption), a shift of the Rpt minimum towards larger angles, and its widering. For silver gratings with h/a greater than the optimal value, a similar shift and widering of the plasmon resonance is also observed. However, at the same time, a significant deepening of the Rpt minimum is recorded, that is, an increase in the efficiency of SPP excitation. Such changes in the plasmon characteristics also appear on aluminum gratings, however, in this case the effect of the selenium layers is weaker by an order of magnitude. The obtained results allow us to propose a method of correcting the plasmonic characteristics of silver gratings in which the value of h/a is higher than optimal.
- 21 December 2023
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Optoelektronìka ta napìvprovìdnikova tehnìka
- Vol. 58, 158-166
INFLUENCE OF Se THIN FILMS ON THE EXCITATION EFFICIENCY OF SURFACE PLASMON POLARITONS IN SILVER AND ALUMINUM HOLOGRAPHIC GRATINGS
In this paper, we study the effect of thin selenium layers up to 3 nm thick on the efficiency of excitation of surface plasmon polaritons (SPPs). The Se layers were deposited by thermal evaporation in vacuum on the surface of silver and aluminum gratings. Gratings with a groove profile close to sinusoidal and a period equal to а = 694 nm were formed on chalcogenide photoresist films using interference lithography. Then they were coated with layers of the above metals with a thickness of 80–85 nm using thermal evaporation. Registration of SPP excitation on the gratings was carried out by measuring the angular dependences of the intensity of specularly reflected or diffracted p-polarized He-Ne laser radiation on a stand mounted on the basis of a G5M goniometer and a Fedorov table. An atomic force microscope was used to determine the shape of the groove profile and the depth of the grating relief. It has been found that for silver gratings with a relief modulation depth h/a less than the optimal value (which ensures maximum plasmon absorption, i.e., the maximum efficiency of SPP excitation), selenium deposition causes significant degradation of the plasmon resonance: a decrease in the depth of the minimum of the total reflection Rpt (i.e., a decrease in the efficiency of plasmon absorption), a shift of the Rpt minimum towards larger angles, and its widering. For silver gratings with h/a greater than the optimal value, a similar shift and widering of the plasmon resonance is also observed. However, at the same time, a significant deepening of the Rpt minimum is recorded, that is, an increase in the efficiency of SPP excitation. Such changes in the plasmon characteristics also appear on aluminum gratings, however, in this case the effect of the selenium layers is weaker by an order of magnitude. The obtained results allow us to propose a method of correcting the plasmonic characteristics of silver gratings in which the value of h/a is higher than optimal.
- 7 June 2023
- Published by Springer Nature in Applied Nanoscience
- Vol. 13 (11) , 7187-7194
Formation of silicon nanocomposites by annealing of (SiOx/Sm)n multilayers: luminescence, Raman and FTIR studies
- 7 June 2023
- Published by Springer Nature in Applied Nanoscience
- Vol. 13 (11) , 7187-7194
Formation of silicon nanocomposites by annealing of (SiOx/Sm)n multilayers: luminescence, Raman and FTIR studies
- 8 November 2022
- Published by Springer Nature in Plasmonics
- Vol. 17 (6) , 2459-2466
Excitation of Surface Plasmon Polaritons on Aluminum-Coated Diffraction Gratings Formed on an Inorganic Chalcogenide Photoresist: Influence of Profile Shape
- 8 November 2022
- Published by Springer Nature in Plasmonics
- Vol. 17 (6) , 2459-2466
Excitation of Surface Plasmon Polaritons on Aluminum-Coated Diffraction Gratings Formed on an Inorganic Chalcogenide Photoresist: Influence of Profile Shape