Masaaki Okubo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Masaaki Okubo has a total of 137 co-authors. Here are the top co-authors by number of shared publications:
- Tomoyuki Kuroki
Department of Mechanical Engineering, Osaka Metropolitan University, Sakai, Japan
41 shared publications Tomoyuki Kuroki
Department of Mechanical Engineering, Osaka Metropolitan University, Sakai, Japan
17 shared publications- Toshiaki Yamamoto
Osaka Prefecture University
9 shared publications - Haruhiko Yamasaki
Department of Mechanical Engineering, Osaka Metropolitan University, Sakai, Japan
8 shared publications - Takuya Kuwahara
日本工業大学大学
8 shared publications Haruhiko Yamasaki
Department of Mechanical Engineering, Osaka Metropolitan University, Sakai, Japan
6 shared publications
Latest Publications
- 4 March 2026
- Published by Springer Nature in Plasma Chemistry and Plasma Processing
- Vol. 46 (3) , 42
Nonthermal Plasma Aftertreatment for Low-emission Diesel Engines To Achieve Ultra-clean Power Generation
- 4 March 2026
- Published by Springer Nature in Plasma Chemistry and Plasma Processing
- Vol. 46 (3) , 42
Nonthermal Plasma Aftertreatment for Low-emission Diesel Engines To Achieve Ultra-clean Power Generation
- 12 February 2026
- Published by Elsevier in Journal of Electrostatics
- Vol. 140
Electrostatic discharge-assisted CO2 reduction technologies: A review
- 12 February 2026
- Published by Elsevier in Journal of Electrostatics
- Vol. 140
Electrostatic discharge-assisted CO2 reduction technologies: A review
- Open Access
- 2 January 2026
- Published by Elsevier in Results in Engineering
- Vol. 29
Ozone injection-chemical hybrid process for simultaneous removal of NOx and SOx from ammonia-coal co-firing exhaust gas
- 2 January 2026
- Published by Elsevier in Results in Engineering
- Vol. 29
Open AccessOzone injection-chemical hybrid process for simultaneous removal of NOx and SOx from ammonia-coal co-firing exhaust gas
- 24 October 2025
- Published by Springer Nature in Plasma Chemistry and Plasma Processing
- Vol. 45 (6) , 1807-1825
Composite Rubber–Fluoropolymer Tube with Enhanced Interfacial Adhesion via Dielectric Barrier Discharge Induced Polymerization Surface Treatment
- 24 October 2025
- Published by Springer Nature in Plasma Chemistry and Plasma Processing
- Vol. 45 (6) , 1807-1825
Composite Rubber–Fluoropolymer Tube with Enhanced Interfacial Adhesion via Dielectric Barrier Discharge Induced Polymerization Surface Treatment
- 1 September 2025
- Published by Elsevier in Journal of Electrostatics
- Vol. 137
Nonthermal plasma surface modification of fluoropolymer plastic films: A review (invited paper)
- 1 September 2025
- Published by Elsevier in Journal of Electrostatics
- Vol. 137
Nonthermal plasma surface modification of fluoropolymer plastic films: A review (invited paper)
- 15 July 2025
- Published by Springer Nature
- p. 1-27
Basic Laws of Electrical Circuits
- 15 July 2025
- Published by Springer Nature
- p. 67-77
Impedance Matching and Energy Conversion (2): Smith Chart and Matching Circuit Design Method
- 15 July 2025
- Published by Springer Nature
- p. 67-77
Impedance Matching and Energy Conversion (2): Smith Chart and Matching Circuit Design Method
- 15 July 2025
- Published by Springer Nature
- p. 169-191
Gas Turbine Combined Cycle (GTCC) and Renewable Energy Technologies
- 15 July 2025
- Published by Springer Nature
- p. 169-191
Gas Turbine Combined Cycle (GTCC) and Renewable Energy Technologies
- 8 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 62 (1) , 684-692
Numerical and Experimental Analysis of Plasma-Chemical Hybrid Process for Emission Control of Fossil-Fuel Fired Glass Melting Furnace
Inductive power transfer (IPT) is a promising solution for autonomous unmanned aerial systems (UAS), but stringent size and weight constraints demand ultra-compact receiver designs. This work proposes a compensation-less center-tapped (CT) receiver for high-coupling IPT systems integrated into a reconfigurable drone powertrain. The system operates as a two-stage IPT architecture, combining a CT rectifier with a powertrain-integrated, two-phase interleaved synchronous buck converter during charging mode. This paper derives a differential–equation-based model that describes the operation of a CT rectifier in an LCC-None IPT system. Moreover, the model quantifies the effect of system parameters and parasitic components on diode voltage overshoot. A multi-objective optimization (MOO) framework maximizes efficiency and gravimetric power density while minimizing diode voltage overshoot. Two methods are evaluated to suppress diode voltage overshoot: (1) a passive snubber circuit and (2) a clamping capacitor. An optimum design is selected and prototyped, delivering an output power of 1.74kW to a 48-V battery. The system reaches a peak efficiency of 89.5% with a total added weight of 372.1 g. This represents a practical power-to-weight ratio of 4.7 W/g—the highest gravimetric power density reported so far for this UAS IPT charging level.
- 8 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 62 (1) , 684-692
Numerical and Experimental Analysis of Plasma-Chemical Hybrid Process for Emission Control of Fossil-Fuel Fired Glass Melting Furnace
Inductive power transfer (IPT) is a promising solution for autonomous unmanned aerial systems (UAS), but stringent size and weight constraints demand ultra-compact receiver designs. This work proposes a compensation-less center-tapped (CT) receiver for high-coupling IPT systems integrated into a reconfigurable drone powertrain. The system operates as a two-stage IPT architecture, combining a CT rectifier with a powertrain-integrated, two-phase interleaved synchronous buck converter during charging mode. This paper derives a differential–equation-based model that describes the operation of a CT rectifier in an LCC-None IPT system. Moreover, the model quantifies the effect of system parameters and parasitic components on diode voltage overshoot. A multi-objective optimization (MOO) framework maximizes efficiency and gravimetric power density while minimizing diode voltage overshoot. Two methods are evaluated to suppress diode voltage overshoot: (1) a passive snubber circuit and (2) a clamping capacitor. An optimum design is selected and prototyped, delivering an output power of 1.74kW to a 48-V battery. The system reaches a peak efficiency of 89.5% with a total added weight of 372.1 g. This represents a practical power-to-weight ratio of 4.7 W/g—the highest gravimetric power density reported so far for this UAS IPT charging level.