TKTomoyuki Kuroki

Tomoyuki Kuroki

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Tomoyuki Kuroki has a total of 104 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Simultaneous generation of hydrogen and carbon monoxide using a wet-type plasma reactor

    by Haruhiko Yamasaki, Ren Ushida, Tota Hiranaka, Junyang Wei, Tomoyuki Kuroki, Shiori Hori, Hashira Yamamoto, Masaaki Okubo

  • Open Access

    Ozone injection-chemical hybrid process for simultaneous removal of NOx and SOx from ammonia-coal co-firing exhaust gas

    by Takeru Itagaki, Taiga Tanaka, Tomoyuki Kuroki, Haruhiko Yamasaki, Hashira Yamamoto, Masanori Hattori, Masaaki Okubo


  • Numerical and Experimental Analysis of Plasma-Chemical Hybrid Process for Emission Control of Fossil-Fuel Fired Glass Melting Furnace

    by Haruhiko Yamasaki, Ryosuke Kinoshita, Tomoyuki Kuroki, Hashira Yamamoto, Masaaki Okubo

    Inductive power transfer (IPT) is a promising solution for autonomous unmanned aerial systems (UAS), but stringent size and weight constraints demand ultra-compact receiver designs. This work proposes a compensation-less center-tapped (CT) receiver for high-coupling IPT systems integrated into a reconfigurable drone powertrain. The system operates as a two-stage IPT architecture, combining a CT rectifier with a powertrain-integrated, two-phase interleaved synchronous buck converter during charging mode. This paper derives a differential–equation-based model that describes the operation of a CT rectifier in an LCC-None IPT system. Moreover, the model quantifies the effect of system parameters and parasitic components on diode voltage overshoot. A multi-objective optimization (MOO) framework maximizes efficiency and gravimetric power density while minimizing diode voltage overshoot. Two methods are evaluated to suppress diode voltage overshoot: (1) a passive snubber circuit and (2) a clamping capacitor. An optimum design is selected and prototyped, delivering an output power of 1.74kW to a 48-V battery. The system reaches a peak efficiency of 89.5% with a total added weight of 372.1 g. This represents a practical power-to-weight ratio of 4.7 W/g—the highest gravimetric power density reported so far for this UAS IPT charging level.

  • Dry Emission Control Technology for Glass Melting Furnace by Plasma-Chemical Hybrid Processing

    by Haruhiko Yamasaki, Hashira Yamamoto, Yuki Koizumi, Yuta Fukuda, Tomoyuki Kuroki, Masaaki Okubo

    To use the continuous combustion of fossil fuels as a sustainable energy source, a low-cost and energy-saving exhaust gas treatment for NO x , SO x , and suspended particulate matter is required. The plasma hybrid exhaust gas treatment technology proposed by the authors is not only a method of plasma treatment, but also a method that combines it with a chemical process, such as chemical solution stabilizer, to clean exhaust gas. This study reports the simulation and application of glass melting furnace exhaust gas treatment as a practical result of the plasma chemical hybrid process (PCHP). In the experiment, higher removal efficiencies of NO, NO x , and SO x (33, 16, and 55%, respectively) were obtained. The energy efficiency of NO x removal by evaluating the electrical power using the cost of NaOH and the power of ozonizers was measured to be 23 g(NO 2 )/kWh. From comparison, the simulated and experimental temperature distributions and NO x concentration were found to be in good agreements. This indicates that numerical design simulation produces a satisfactory result. PCHP can potentially be the most suitable method for exhaust gas treatment in glass melting furnaces.


  • Higher Adhesion Strength Over 10 N/mm Between Rubber and Fluoropolymer Film When Treated by Atmospheric Plasma-Graft Polymerization

    by Tomoyuki Kuroki, Mitsuru Narita, Takumi Kageyama, Haruhiko Yamasaki, Takuya Matsumoto, Tsuyoshi Ida, Masaaki Okubo

    An evaluation of the adhesion between rubber and fluoropolymer films treated by atmospheric plasma-graft polymerization is conducted to realize a low-permeation fuel rubber hose covered with fluoropolymer. The low-permeation fuel rubber hose is important for reducing vehicular evaporative emissions. Although fluoropolymers have extremely low permeability for fuel, it is difficult to bond them with other materials, such as rubber, because of their low adhesive properties. Plasma surface modification has been investigated to improve the adhesive properties of fluoropolymers. However, it is difficult to realize effective and permanent surface treatment using plasma alone. Based on the new and effective combined plasma surface-modification technique for fluoropolymer films, we previously proposed an atmospheric-pressure plasma method followed by graft polymerization of hydrophilic monomers such as acrylic acid (CH 2 =CHCOOH). In this study, three types of rubber, isobutylene isoprene rubber (IIR), ethylene acrylic elastomer (AEM), as well as white-colored ethylene acrylic elastomer (white AEM), and two types of fluoropolymer films, denatured PFA-1 and denatured PFA-2, were prepared. The treated fluoropolymer film and rubber were adhered using vulcanized adhesion, and then the 180° peeling strength test was conducted. The results show that an average peeling strength of 12.6 N/mm and a maximum peeling strength of 15.3 N/mm, which are over 10 N/mm, are attained for the sample of vulcanized bonding of the treated denatured PFA-1 and AEM.


  • Toward Ideal VOCs and Nanoparticle Emission Control Technology Using a Wet-Type Catalysis Nonthermal Plasma Reactor

    by Haruhiko Yamasaki, Kohei Kishimoto, Takumi Shimada, Tomoyuki Kuroki, Jinkyu Kang, Dongwook Kim, Tadao Yagi, Masaaki Okubo

    Several exhaust gas regulations are being implemented to prevent the hazardous emissions of volatile organic compounds (VOCs) and particulate matter (PM) from paint and print factories. The VOCs generate photochemical oxidants and suspended PM, such as PM 2.5 , which has become a global environmental problem. We evaluate the catalytic nonthermal plasma (NTP) technique for controlling the emission of VOCs. The article proposes a wet-type catalysis plasma reactor to extend the treatment of water-soluble VOCs. Initial evaluation of the proposed technique involves simultaneous removal of nanoparticles along with individual VOCs, toluene, acetaldehyde, acetic acid, and ammonia, at a relatively high gas flow rate of 10 L/min. Further, pellets of α -alumina and TiO 2 spheres are employed in the NTP reactors for assessing their catalytic performance. We install an MnO 2 catalytic reactor downstream of the plasma reactor for ozone removal. Simultaneous treatment of typical VOCs and nanoparticles using dry and wet-type catalytic NTP reactors shows that the wet-type reactor has superior average particle collection efficiency of 100%. However, the dry-type NTP with α -alumina shows a higher toluene removal efficiency of 91% compared to 73% in the wet type. Further, the respective removal efficiencies for acetaldehyde, acetic acid, and ammonia are 100%, 100%, and 95%. Notably, the toluene removal efficiency drops to 65% with the TiO 2 catalyst.


  • Performance Improvement in Semi-dry Ozone Injection NOx and SOx Removal Process for a Glass Furnace Flue Gas

    by Yuta Fukuda, Tomoyuki Kuroki, Ryosuke Nishioka, Hidekatsu Fujishima, Haruhiko Yamasaki, Hashira Yamamoto, Masaaki Okubo

    A combined ozone injection and semi-dry chemical NOx and SOx removal process using nonthermal plasma for the treatment of flue gases emitted from glass melting furnaces has been proposed. To further improve the NOx removal, O3 was injected in directions opposite to the direction of gas flow at the center of the semi-dry reactor. Moreover, the effect of the increase in initial concentrations of NO and SO2 was investigated. In addition, the effect of the gas flow rate on NO oxidation, denitration, and desulfurization efficiencies, and the effect of NaOH and SO32− concentrations on denitration and desulfurization efficiencies were investigated.


  • Toward NO x /SO x and Nanoparticle Control Technology Using a Single-Stage Wet-Type Nonthermal Plasma Reactor

    by Haruhiko Yamasaki, Shunto Nomura, Xi Xun, Tomoyuki Kuroki, Jinkyu Kang, Tadao Yagi, Masaaki Okubo

    Nitrogen oxides ( NO x ), sulfur oxides ( SO x ), and particulate matter (PM) emitted by diesel engines, thermal power generation plants, and various industrial establishments have had unfavorable effects on the environment globally. Therefore, it is necessary to install aftertreatment systems on such combustors because the emissions cannot be treated for combustion improvement only. To establish NO x /SO x , and nanoparticle control technologies, herein, we propose a single-stage wet-type nonthermal plasma (NTP) reactor. To evaluate the performance of the proposed system, we conducted a laboratory-scale experiment with a mixture of NO x , SO x , and polystyrene particles. In this system, PM is collected in a water film by the electrostatic effect, NO is oxidized to NO 2 by NTP, and NO 2 and SO 2 are absorbed into a water film on the inner wall of the reactor. We achieved almost complete and simultaneous removal of the pollutants, with a partial collection efficiency of more than 98% for the nanoparticles (diameter = 22-334 nm), removal efficiency of 98% for NO x , and removal efficiency of 99% for SO x . Furthermore, we proposed a method to treat the chemical components left in the water film to enable a self-sustaining technique. The technology allows for conserving in space and investment costs in exhaust gas aftertreatment facilities.


  • Adsorbed CO2 Dissociation Using Argon and Helium Nonthermal Plasma Flows

    by Haruhiko Yamasaki, Satoshi Kamei, Tomoyuki Kuroki, Masaaki Okubo

    In recent years, global warming has become a worldwide problem. Carbon dioxide ( $CO_2$ ) is one of the primary substances causing global warming, and its emission should be reduced. A promising technology is the conversion of $CO_2$ to carbon monoxide (CO) using plasma treatment, so that the CO itself or its conversion to methane can be used as fuel for combustion engines. In this study, a $CO_2$ dissociation or reduction treatment system using an adsorbent and nonthermal plasma (NTP) flow is investigated. To improve the conversion efficiency, the conversion efficiency for Ar or He plasma is evaluated. In the physical adsorption process, ~10% $CO_2$ gas with a flow rate of 10 L/min is prepared, and then, it is introduced into the flow channel; $CO_2$ is adsorbed by the adsorbent. After the adsorption process, the circulation flow channel is set, and then, the Ar or He NTP flow is generated with a blower. As a result, the adsorbed $CO_2$ is desorbed with $CO_2$ concentrations of 20 and 23% by the Ar NTP flow and the He NTP flow, respectively. The $CO_2$ conversion efficiency reaches 21%, and the energy efficiencies reach 13 and 10% with plasma in the cases using the Ar and He NTP flows, respectively. The energy efficiency with regard to CO is better with the Ar plasma, but more atomic carbon can be generated using the He plasma.