Rendra Panca Anugraha
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Rendra Panca Anugraha has a total of 56 co-authors. Here are the top co-authors by number of shared publications:
- Gede Wibawa
Department of Chemical Engineering, Institut Teknologi Sepuluh Nopember, Surabaya, 60111, Indonesia
4 shared publications Juwari Juwari
Department of Chemical Engineering, Institut Teknologi Sepuluh Nopember, Kampus ITS Sukolilo, Surabaya, Indonesia 60111, Indonesia
4 shared publications- Renanto Handogo
Department of Chemical Engineering, Sepuluh Nopember Institute of Technology, Surabaya, Indonesia
3 shared publications Renanto Renanto
Department of Chemical Engineering, Institut Teknologi Sepuluh Nopember, Kampus ITS Sukolilo, Surabaya, Indonesia 60111, Indonesia
3 shared publications- Vibianti Dwi Pratiwi
Department of Chemical Engineering, Faculty of Industrial Technology, Institut Teknologi Nasional Bandung
3 shared publications - Annas Wiguno
Department of Chemical Engineering, Faculty of Industrial Technology, Institut Teknologi Sepuluh Nopember, Kampus ITS Sukolilo, Surabaya 60111, Indonesia
2 shared publications
Latest Publications
- Open Access
- 6 August 2026
- Published by Institute of Research and Community Services Diponegoro University (LPPM UNDIP) in Reaktor
- Vol. 26 (2)
Techno-Economic Analysis of Biodiesel Production from Microalgae
The increasing global energy demand and the urgent necessity to mitigate greenhouse gas emissions have driven the exploration of renewable energy alternatives to fossil-based fuels, such as biofuels derived from sustainable biological sources. Among various potential feedstocks, microalgae have gained considerable attention due to their high lipid productivity, rapid growth rate, and ability to utilize CO₂ efficiency through photosynthesis. This study presents the design and techno-economic evaluation of a biodiesel production plant utilizing Chlorella vulgaris microalgae as the primary feedstock. The cultivation process employs a Flat Plate Photobioreactor (FPPBR) system to enhance biomass productivity under controlled light and nutrient conditions. The production process adopts the Lurgi technology, beginning with the extraction of microalgae oil using n-hexane solvent, which is subsequently converted into biodiesel through esterification and transesterification reactions catalyzed by H₂SO₄ and NaOH, respectively. The designed plant capacity is 100,000 kL of biodiesel per year. Bontang, East Kalimantan, is selected as the plant site considering key factors such as raw material availability, access to utilities, land suitability, and transportation infrastructure. The plant consists of two main stages: microalgae oil production and biodiesel synthesis, with a total construction period of two years and an operational lifespan of 15 years. Economic feasibility analysis indicates an Internal Rate of Return (IRR) of 12.91%, a Net Present Value (NPV) of IDR 2,296,063,930,982, and a payback period of 13 years, confirming the financial viability of the project. These results demonstrate that biodiesel production from Chlorella vulgaris microalgae is both technically feasible and economically sustainable, providing a practical and scalable pathway to support Indonesia’s transition toward renewable and low-carbon energy systems.
- 6 August 2026
- Published by Institute of Research and Community Services Diponegoro University (LPPM UNDIP) in Reaktor
- Vol. 26 (2)
Open AccessTechno-Economic Analysis of Biodiesel Production from Microalgae
The increasing global energy demand and the urgent necessity to mitigate greenhouse gas emissions have driven the exploration of renewable energy alternatives to fossil-based fuels, such as biofuels derived from sustainable biological sources. Among various potential feedstocks, microalgae have gained considerable attention due to their high lipid productivity, rapid growth rate, and ability to utilize CO₂ efficiency through photosynthesis. This study presents the design and techno-economic evaluation of a biodiesel production plant utilizing Chlorella vulgaris microalgae as the primary feedstock. The cultivation process employs a Flat Plate Photobioreactor (FPPBR) system to enhance biomass productivity under controlled light and nutrient conditions. The production process adopts the Lurgi technology, beginning with the extraction of microalgae oil using n-hexane solvent, which is subsequently converted into biodiesel through esterification and transesterification reactions catalyzed by H₂SO₄ and NaOH, respectively. The designed plant capacity is 100,000 kL of biodiesel per year. Bontang, East Kalimantan, is selected as the plant site considering key factors such as raw material availability, access to utilities, land suitability, and transportation infrastructure. The plant consists of two main stages: microalgae oil production and biodiesel synthesis, with a total construction period of two years and an operational lifespan of 15 years. Economic feasibility analysis indicates an Internal Rate of Return (IRR) of 12.91%, a Net Present Value (NPV) of IDR 2,296,063,930,982, and a payback period of 13 years, confirming the financial viability of the project. These results demonstrate that biodiesel production from Chlorella vulgaris microalgae is both technically feasible and economically sustainable, providing a practical and scalable pathway to support Indonesia’s transition toward renewable and low-carbon energy systems.
- Open Access
- 1 June 2026
- Published by WNGB Scientific Publishing House Sp. z o.o. in Ecological Engineering & Environmental Technology
- Vol. 27 (6) , 1-15
Resource recovery from Sidoarjo volcanic mud waste: Valorisation into a silicon dioxide–modified fire suppressant for liquefied petroleum gas flame control
The uncontrolled eruption of Sidoarjo mud since 2006 triggered by gas exploration drilling has created one of Indonesia's most severe environmental disasters, discharging millions of cubic meters of volcanic mud annually and threatening surrounding communities. Simultaneously, LPG fire hazards...
- 1 June 2026
- Published by WNGB Scientific Publishing House Sp. z o.o. in Ecological Engineering & Environmental Technology
- Vol. 27 (6) , 1-15
Open AccessResource recovery from Sidoarjo volcanic mud waste: Valorisation into a silicon dioxide–modified fire suppressant for liquefied petroleum gas flame control
The uncontrolled eruption of Sidoarjo mud since 2006 triggered by gas exploration drilling has created one of Indonesia's most severe environmental disasters, discharging millions of cubic meters of volcanic mud annually and threatening surrounding communities. Simultaneously, LPG fire hazards...
- Open Access
- 4 April 2026
- Published by Center of Biomass and Renewable Energy Scientia Academy in International Journal of Renewable Energy Development
- Vol. 15 (3) , 656-664
Development of an isothermal CO2 absorption process using DMC and PEG400 for carbon capture and storage technology
This study aims to develop and evaluate a green binary solvent system based on dimethyl carbonate (DMC) and polyethylene glycol 400 (PEG400) for physical CO2 absorption. Efficient and environmentally benign solvents are essential to support large-scale decarbonization efforts. The DMC–PEG400 system was formulated at molar ratios of 1:2, 1:3, and 1:4 to assess its absorption performance. Isothermal solubility experiments were performed at 303.15–323.15 K and 3–7 bar, complemented by Fourier Transform Infrared (FTIR) spectroscopy to elucidate the absorption mechanism. The FTIR spectra showed the emergence of characteristic CO2 vibrational bands without alterations to the solvent’s fingerprint region, confirming that CO₂ uptake proceeds through physical dissolution rather than chemical interaction. The DMC–PEG400 mixtures demonstrated clear temperature and pressure dependencies typical of physical solvents, with solubility decreasing at elevated temperatures and increasing proportionally with pressure. Among the tested formulations, the 1:3 molar ratio exhibited the highest absorption capacity, achieving 0.0606 mole CO₂/mole solution at 303.15 K and 7 bar. This performance arises from an optimal balance between interaction sites provided by PEG400 and the moderate viscosity needed to facilitate efficient CO2 diffusion. In contrast, the 1:4 mixture displayed reduced capacity due to excessive viscosity and limited free volume. Overall, the results highlight the promising potential of DMC–PEG400 mixtures, particularly at the 1:3 ratio, as tunable and sustainable physical solvents for CO₂ capture. Their favorable solubility behavior, stability, and benign chemical nature position them as viable candidates for next-generation carbon capture and storage (CCS) technologies.
- 4 April 2026
- Published by Center of Biomass and Renewable Energy Scientia Academy in International Journal of Renewable Energy Development
- Vol. 15 (3) , 656-664
Open AccessDevelopment of an isothermal CO2 absorption process using DMC and PEG400 for carbon capture and storage technology
This study aims to develop and evaluate a green binary solvent system based on dimethyl carbonate (DMC) and polyethylene glycol 400 (PEG400) for physical CO2 absorption. Efficient and environmentally benign solvents are essential to support large-scale decarbonization efforts. The DMC–PEG400 system was formulated at molar ratios of 1:2, 1:3, and 1:4 to assess its absorption performance. Isothermal solubility experiments were performed at 303.15–323.15 K and 3–7 bar, complemented by Fourier Transform Infrared (FTIR) spectroscopy to elucidate the absorption mechanism. The FTIR spectra showed the emergence of characteristic CO2 vibrational bands without alterations to the solvent’s fingerprint region, confirming that CO₂ uptake proceeds through physical dissolution rather than chemical interaction. The DMC–PEG400 mixtures demonstrated clear temperature and pressure dependencies typical of physical solvents, with solubility decreasing at elevated temperatures and increasing proportionally with pressure. Among the tested formulations, the 1:3 molar ratio exhibited the highest absorption capacity, achieving 0.0606 mole CO₂/mole solution at 303.15 K and 7 bar. This performance arises from an optimal balance between interaction sites provided by PEG400 and the moderate viscosity needed to facilitate efficient CO2 diffusion. In contrast, the 1:4 mixture displayed reduced capacity due to excessive viscosity and limited free volume. Overall, the results highlight the promising potential of DMC–PEG400 mixtures, particularly at the 1:3 ratio, as tunable and sustainable physical solvents for CO₂ capture. Their favorable solubility behavior, stability, and benign chemical nature position them as viable candidates for next-generation carbon capture and storage (CCS) technologies.
- Open Access
- 21 November 2025
- Published by Elsevier in Results in Engineering
- Vol. 28
Analysis of CO2 injection strategy and storage in the kujung formation using reservoir simulation
- 21 November 2025
- Published by Elsevier in Results in Engineering
- Vol. 28
Open AccessAnalysis of CO2 injection strategy and storage in the kujung formation using reservoir simulation
- 30 July 2024
- Published by Wiley in Chemical Engineering & Technology
- Vol. 48 (2)
Analysis of Solar Thermal Energy Integration in the Industry in Indonesia
This study focuses on designing a solar thermal system utilizing parabolic trough collectors to replace conventional heat requirements in industrial processes. The research also assesses the impact of implementing this system on reducing CO2 emissions and provides economic analysis for industrial cities from two geographically different islands in Indonesia: Java and Sulawesi. This study uses a parabolic trough collector to absorb energy from sunlight. Based on the calculation of the energy balance of the solar collector, the average heat absorbed by the collector is 545.5 kJ m−2 h−1 in Java and 606.5 kJ m−2 h−1 in Sulawesi. As a result, approximately 67.55 tonnes of CO2 per day will be mitigated by transitioning from conventional processes. The economic analysis indicates a payback period of 3.54 years, a net present value of 1.4 million USD, and an internal rate of return of 12 % based on fuel savings.
- 30 July 2024
- Published by Wiley in Chemical Engineering & Technology
- Vol. 48 (2)
Analysis of Solar Thermal Energy Integration in the Industry in Indonesia
This study focuses on designing a solar thermal system utilizing parabolic trough collectors to replace conventional heat requirements in industrial processes. The research also assesses the impact of implementing this system on reducing CO2 emissions and provides economic analysis for industrial cities from two geographically different islands in Indonesia: Java and Sulawesi. This study uses a parabolic trough collector to absorb energy from sunlight. Based on the calculation of the energy balance of the solar collector, the average heat absorbed by the collector is 545.5 kJ m−2 h−1 in Java and 606.5 kJ m−2 h−1 in Sulawesi. As a result, approximately 67.55 tonnes of CO2 per day will be mitigated by transitioning from conventional processes. The economic analysis indicates a payback period of 3.54 years, a net present value of 1.4 million USD, and an internal rate of return of 12 % based on fuel savings.
- 29 May 2024
- Published by Taylor & Francis in Chemical Engineering Communications
- Vol. 211 (9) , 1431-1444
Optimization of superstructure network in the CCS/CCSU system for CO 2 reduction from exhaust gas industry and gas field in Indonesia as archipelago state
- 29 May 2024
- Published by Taylor & Francis in Chemical Engineering Communications
- Vol. 211 (9) , 1431-1444
Optimization of superstructure network in the CCS/CCSU system for CO 2 reduction from exhaust gas industry and gas field in Indonesia as archipelago state
- 28 December 2023
- Published by Elsevier in Chemical Engineering Research and Design
- Vol. 202, 226-234
Techno-economic analysis of CO2 cryogenic distillation from high CO2 content gas field: A case study in Indonesia
- 28 December 2023
- Published by Elsevier in Chemical Engineering Research and Design
- Vol. 202, 226-234
Techno-economic analysis of CO2 cryogenic distillation from high CO2 content gas field: A case study in Indonesia
- Open Access
- 29 April 2023
- Published by Universitas Gadjah Mada in ASEAN Journal of Chemical Engineering
- Vol. 23 (1) , 14-27
Heat Exchanger Network (HEN) Analysis of The Power Plant Industry Using Aspen Energy Analyzer Software
Heat recovery is considered as the key to improve energy efficiency in the process design. An appropriate heat exchanger network (HEN) design is an effective tool to maximize heat recovery from the process streams and to minimize energy consumption. The objectives of this study were arranging optimum HEN based on the annual cost in the power industry. HEN in the Paiton Steam Power Plant, East Java, Indonesia, was designed using spreadsheet and Aspen Energy Analyzer with Peng-Robinson equation. Pinch analysis was conducted by comparing Tmin (10°C - 19°C) to obtain Maximum Energy Recovery (MER) and Heat Exchanger Area (HEA). The HEN design was optimized using grid diagram. Simulation in this study succeeded to reduce the annual cost the most effectively at ∆Tmin 16°C. This design optimized the process integration and contributed to the capital, operation, and total annual cost reduction of 14.3%. The maximum energy recovery was 286,706 kW and HEA 138.790 m2. This result is a solution for Steam Power Plant as an effort for enhancing energy efficiency and the company competitiveness.
- 29 April 2023
- Published by Universitas Gadjah Mada in ASEAN Journal of Chemical Engineering
- Vol. 23 (1) , 14-27
Open AccessHeat Exchanger Network (HEN) Analysis of The Power Plant Industry Using Aspen Energy Analyzer Software
Heat recovery is considered as the key to improve energy efficiency in the process design. An appropriate heat exchanger network (HEN) design is an effective tool to maximize heat recovery from the process streams and to minimize energy consumption. The objectives of this study were arranging optimum HEN based on the annual cost in the power industry. HEN in the Paiton Steam Power Plant, East Java, Indonesia, was designed using spreadsheet and Aspen Energy Analyzer with Peng-Robinson equation. Pinch analysis was conducted by comparing Tmin (10°C - 19°C) to obtain Maximum Energy Recovery (MER) and Heat Exchanger Area (HEA). The HEN design was optimized using grid diagram. Simulation in this study succeeded to reduce the annual cost the most effectively at ∆Tmin 16°C. This design optimized the process integration and contributed to the capital, operation, and total annual cost reduction of 14.3%. The maximum energy recovery was 286,706 kW and HEA 138.790 m2. This result is a solution for Steam Power Plant as an effort for enhancing energy efficiency and the company competitiveness.
- Open Access
- 1 April 2020
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 778 (1)
Process Design and Steady State Simulation of Natural Gas Dehydration Using Triethylene Glycol (TEG) to Obtain The Optimum Total Annual Costs (TAC)
Natural gas is one of the most desired raw materials which can be used in petrochemical industries or as energy resource. Natural gas usually obtained from underground reservoirs and it must go through purification process so it can be utilized. All acid gas compounds such as H2S, CO2 and all liquids including H2O must be removed. Most industries use triethylene glycol (TEG) dehydration unit to absorb water from natural gas streams. Therefore, further research about design and optimization of dehydration unit using TEG should be conducted since the optimization of dehydration unit using TEG affects to safety, operability, and stability of the process. In this study, the optimization of TEG Dehydration Unit process is conducted to minimize the Total Annual Costs (TAC) and improve the efficiency of the process. Aspen Plus software is used to perform the simulation of TEG dehydration process. Optimization is conducted by changing several of the base case operating conditions which have been created using existing condition to obtain the optimum conditions with minimum TAC on the existing circumstances. The variables that are used in this research is absorber column pressure (35-45 barg with 2.5 barg interval) and lean TEG temperature (39-49°C with 2°C interval). The constrain of the absorber column pressure is less than 45 barg, since the natural gas feed pressure from well is 45.16 barg. The results show that by changing some operating conditions can reduce the size of the column, reduce the energy costs including steam, cooling water, and electricity costs. Therefore, it can reduce the TAC of the natural gas dehydration unit. The validation simulation results of the steady state of the TEG Dehydration Unit using Aspen Plus and the real plant produces relatively small % error, so it can be used to create a base case using the existing data. The mole fraction of H2O in dehydrated gas after optimization using Aspen Plus is 0.000178 while in real plant the result is 0.000200. The simulation results can reduce the TAC from 3, 416, 739 USD to 2, 973, 219 USD.
- 1 April 2020
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 778 (1)
Open AccessProcess Design and Steady State Simulation of Natural Gas Dehydration Using Triethylene Glycol (TEG) to Obtain The Optimum Total Annual Costs (TAC)
Natural gas is one of the most desired raw materials which can be used in petrochemical industries or as energy resource. Natural gas usually obtained from underground reservoirs and it must go through purification process so it can be utilized. All acid gas compounds such as H2S, CO2 and all liquids including H2O must be removed. Most industries use triethylene glycol (TEG) dehydration unit to absorb water from natural gas streams. Therefore, further research about design and optimization of dehydration unit using TEG should be conducted since the optimization of dehydration unit using TEG affects to safety, operability, and stability of the process. In this study, the optimization of TEG Dehydration Unit process is conducted to minimize the Total Annual Costs (TAC) and improve the efficiency of the process. Aspen Plus software is used to perform the simulation of TEG dehydration process. Optimization is conducted by changing several of the base case operating conditions which have been created using existing condition to obtain the optimum conditions with minimum TAC on the existing circumstances. The variables that are used in this research is absorber column pressure (35-45 barg with 2.5 barg interval) and lean TEG temperature (39-49°C with 2°C interval). The constrain of the absorber column pressure is less than 45 barg, since the natural gas feed pressure from well is 45.16 barg. The results show that by changing some operating conditions can reduce the size of the column, reduce the energy costs including steam, cooling water, and electricity costs. Therefore, it can reduce the TAC of the natural gas dehydration unit. The validation simulation results of the steady state of the TEG Dehydration Unit using Aspen Plus and the real plant produces relatively small % error, so it can be used to create a base case using the existing data. The mole fraction of H2O in dehydrated gas after optimization using Aspen Plus is 0.000178 while in real plant the result is 0.000200. The simulation results can reduce the TAC from 3, 416, 739 USD to 2, 973, 219 USD.