Kristopher Orlowski
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Kristopher Orlowski has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Shanaka Kristombu Baduge
Department of Infrastructure Engineering, The University of Melbourne, Parkville, VIC 3052, Australia
7 shared publications - Priyan Mendis
Department of Infrastructure Engineering, The University of Melbourne, Parkville 3010, Australia
6 shared publications - David Kennedy
School of Engineering, Cardiff University, Cardiff CF24 3AA, UK
1 shared publication Priyan Mendis
Professor, Centre for Advanced Manufacturing of Prefabricated Housing, Dept. of Infrastructure Engineering, Univ. of Melbourne, Parkville, VIC 3010, Australia
1 shared publicationYusak Oktavianus
1 shared publication- Yusak Oktavianus
University of Melbourne
1 shared publication
Latest Publications
- 1 February 2021
- Published by American Society of Civil Engineers (ASCE) in Journal of Structural Engineering
- Vol. 147 (2) , 04020325
Prefabricated Composite Steel-Timber Stiffened Wall Systems with Post-Tensioning: Structural Analysis and Experimental Investigation under Vertical Axial Load
With increasing demand for midrise buildings, automated prefabrication, design for manufacturing and assembly (DfMA), and sustainability, a novel material-efficient post-tensioned (PT) composite steel-timber (CST) stiffened wall system has been developed. As opposed to cross-laminated timber (CLT), this fully prefabricated panelized composite system consists of an engineered wood panel that is integrally stiffened by timber studs and steel square hollow sections (SHS). Each SHS additionally accommodates a PT rod and panel-to-panel connections, allowing for quick onsite assembly, permanent tie-down, and self-centering inverted pendulum rocking. This study presents and evaluates the structural buckling behavior and performance of these systems under vertical axial loading in terms of failure modes, serviceability, ultimate limit states, midheight out-of-plane deflection along the width of the wall, and PT force loss. This has been achieved through an extensive experimental investigation and analysis consisting a total of 10 PT-CST stiffened walls with multiple variables including level of post-tensioning, wall height, end conditions, and the connection between the panel and SHS and the panel and stud stiffeners. Complex behavior through several modes of failure was observed with the increased application of initial PT force, which in turn reduced the ultimate capacity. Additionally, it was found that PT force reduction due to vertical axial loading even within the serviceability limit state (SLS) is significant. Thus, it is recommended that this reduced PT force be considered in design.
- 1 February 2021
- Published by American Society of Civil Engineers (ASCE) in Journal of Structural Engineering
- Vol. 147 (2) , 04020325
Prefabricated Composite Steel-Timber Stiffened Wall Systems with Post-Tensioning: Structural Analysis and Experimental Investigation under Vertical Axial Load
With increasing demand for midrise buildings, automated prefabrication, design for manufacturing and assembly (DfMA), and sustainability, a novel material-efficient post-tensioned (PT) composite steel-timber (CST) stiffened wall system has been developed. As opposed to cross-laminated timber (CLT), this fully prefabricated panelized composite system consists of an engineered wood panel that is integrally stiffened by timber studs and steel square hollow sections (SHS). Each SHS additionally accommodates a PT rod and panel-to-panel connections, allowing for quick onsite assembly, permanent tie-down, and self-centering inverted pendulum rocking. This study presents and evaluates the structural buckling behavior and performance of these systems under vertical axial loading in terms of failure modes, serviceability, ultimate limit states, midheight out-of-plane deflection along the width of the wall, and PT force loss. This has been achieved through an extensive experimental investigation and analysis consisting a total of 10 PT-CST stiffened walls with multiple variables including level of post-tensioning, wall height, end conditions, and the connection between the panel and SHS and the panel and stud stiffeners. Complex behavior through several modes of failure was observed with the increased application of initial PT force, which in turn reduced the ultimate capacity. Additionally, it was found that PT force reduction due to vertical axial loading even within the serviceability limit state (SLS) is significant. Thus, it is recommended that this reduced PT force be considered in design.
- 1 October 2020
- Published by Elsevier in Structures
- Vol. 27, 1670-1681
Design curves for stiffened engineered timber wall systems: A verified analytical approach
- 1 October 2020
- Published by Elsevier in Structures
- Vol. 27, 1670-1681
Design curves for stiffened engineered timber wall systems: A verified analytical approach
- 21 March 2020
- Published by Elsevier in Structures
- Vol. 25, 360-369
Failure modes and behaviour of stiffened engineered timber wall systems under axial-loading
- 21 March 2020
- Published by Elsevier in Structures
- Vol. 25, 360-369
Failure modes and behaviour of stiffened engineered timber wall systems under axial-loading
- 1 February 2020
- Published by Elsevier in Engineering Structures
- Vol. 204
Verified and validated design curves and strength reduction factors for post-tensioned composite steel-timber stiffened wall systems
- 1 February 2020
- Published by Elsevier in Engineering Structures
- Vol. 204
Verified and validated design curves and strength reduction factors for post-tensioned composite steel-timber stiffened wall systems
- 1 January 2020
- Published by Elsevier in Automation in Construction
- Vol. 109
Automated manufacturing for timber-based panelised wall systems
- 1 January 2020
- Published by Elsevier in Automation in Construction
- Vol. 109
Automated manufacturing for timber-based panelised wall systems
- 1 December 2019
- Published by Elsevier in Structures
- Vol. 22, 230-244
Structural behaviour of prefabricated stressed-skin engineered timber composite flooring systems
- 1 December 2019
- Published by Elsevier in Structures
- Vol. 22, 230-244
Structural behaviour of prefabricated stressed-skin engineered timber composite flooring systems
- Open Access
- 21 August 2019
- Published by Crimson Publishers in Advancements in Civil Engineering & Technology
- Vol. 3 (4) , 1-3
Review of Timber connections: Connector Plate, Cleats, Studies and Dovetail Connections
- 21 August 2019
- Published by Crimson Publishers in Advancements in Civil Engineering & Technology
- Vol. 3 (4) , 1-3
Open AccessReview of Timber connections: Connector Plate, Cleats, Studies and Dovetail Connections
- Open Access
Assessment of Manufacturing Processes for Automated Timber-Based Panelised Prefabrication
The manufacturing processes involved in the prefabrication of timber-based panelised walls is presented and explored in this study, through current industry practice and the latest automated technological solutions. A weighted Multi Criteria Analysis (MCA) was constructed as a preliminary mechanism for assessment of current practices in conducting manufacturing processes compared to leading automated solutions. The developed method can be used to evaluate any timber-based wall panel manufacturing assembly line and to suggest recommended automation-based improvements on a process level in order to achieve prefabricated manufacturing objectives specific to local conditions and requirements. This has been demonstrated and verified through a case study with an industry partner. The resultant recommendations obtained close the knowledge gaps in the market and academia in uncovering recommended areas for investment and development to advance assembly lines at certain key processes in the production of timber-based walls for panelised construction.
Open AccessAssessment of Manufacturing Processes for Automated Timber-Based Panelised Prefabrication
The manufacturing processes involved in the prefabrication of timber-based panelised walls is presented and explored in this study, through current industry practice and the latest automated technological solutions. A weighted Multi Criteria Analysis (MCA) was constructed as a preliminary mechanism for assessment of current practices in conducting manufacturing processes compared to leading automated solutions. The developed method can be used to evaluate any timber-based wall panel manufacturing assembly line and to suggest recommended automation-based improvements on a process level in order to achieve prefabricated manufacturing objectives specific to local conditions and requirements. This has been demonstrated and verified through a case study with an industry partner. The resultant recommendations obtained close the knowledge gaps in the market and academia in uncovering recommended areas for investment and development to advance assembly lines at certain key processes in the production of timber-based walls for panelised construction.
- 1 December 2018
- Published by Elsevier in Engineering Structures
- Vol. 176, 555-568
Structural behaviour of prefabricated load bearing braced composite timber wall system
- 1 December 2018
- Published by Elsevier in Engineering Structures
- Vol. 176, 555-568
Structural behaviour of prefabricated load bearing braced composite timber wall system
- Open Access
Manufacturing, Modeling, Implementation and Evaluation of a Weatherproof Seal for Prefabricated Construction
Prefabricated forms of construction have led to the rapid onsite assembly of buildings however there are still on-site tasks and processes which can be reevaluated and redone specifically in keeping with the principles of prefabrication instead being adapted to fit its purpose. One such process is that of waterproofing between prefabricated panels and modules which come from the factory fully complete façade and all. Conventional means of waterproofing can be used however it results in more work done on site, potential delays and generally requires access from the external face of the building. This paper presents the Modelling, Implementation and Evaluation of purpose developed weatherproof seals specific for Prefabricated Construction. An overview is provided of the entire development process and specific focus is given to the modeling using finite element analysis (FEA) computer simulations, manufacturing and testing which then resulted in the implementation in a prefabricated panelised building which is used as a case study and the means of further evaluation. These strategies have enabled an efficient and robust prefabricated waterproofing solution specific for this form of construction to be understood and implemented. The resulting case study has successfully verified the time and cost savings when compared to conventional techniques whilst still providing a durable and effective weatherproof seal for prefabricated panelised and modular systems.
Open AccessManufacturing, Modeling, Implementation and Evaluation of a Weatherproof Seal for Prefabricated Construction
Prefabricated forms of construction have led to the rapid onsite assembly of buildings however there are still on-site tasks and processes which can be reevaluated and redone specifically in keeping with the principles of prefabrication instead being adapted to fit its purpose. One such process is that of waterproofing between prefabricated panels and modules which come from the factory fully complete façade and all. Conventional means of waterproofing can be used however it results in more work done on site, potential delays and generally requires access from the external face of the building. This paper presents the Modelling, Implementation and Evaluation of purpose developed weatherproof seals specific for Prefabricated Construction. An overview is provided of the entire development process and specific focus is given to the modeling using finite element analysis (FEA) computer simulations, manufacturing and testing which then resulted in the implementation in a prefabricated panelised building which is used as a case study and the means of further evaluation. These strategies have enabled an efficient and robust prefabricated waterproofing solution specific for this form of construction to be understood and implemented. The resulting case study has successfully verified the time and cost savings when compared to conventional techniques whilst still providing a durable and effective weatherproof seal for prefabricated panelised and modular systems.