Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Guifu Ding has a total of 242 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    A Simple Screen-Printing-Based Strategy for High-Temperature Insulation of Metal Substrates for Thin-Film Strain Gauges

    by Nan Zhao, Congchun Zhang, Kaigong Zhao, Sentong Li, Guifu Ding

    The monolithic integration of metal-substrate high-temperature thin-film strain gauge (HTFSG) requires high-performance insulating layers to suppress leakage conduction between the conductive substrate and the sensing layer, thereby ensuring reliable operation under high-temperature conditions. To address this challenge, four representative insulating architectures were designed and systematically evaluated through microstructural characterization, high-temperature electrical insulation measurements, and device-level validation. Among them, the homogeneous bilayer Al2O3 (A/A) architecture formed a dense and continuous insulating layer, achieving an insulation resistance of 1.67×106 Ω at 800 ℃ together with a low resistance drift rate of 1.485%/h, thereby exhibiting superior high-temperature insulation performance and thermal stability. Furthermore, the metal-substrate HTFSG incorporating the optimized A/A insulating architecture exhibited stable piezoresistive responses and excellent cyclic repeatability, demonstrating that the proposed insulating architecture provides reliable electrical isolation between the sensing layer and the conductive substrate. This work presents a simple screen-printing-based strategy for high-temperature electrical insulation of metal-substrate HTFSG, enabling reliable monolithic integration of thin-film sensors on metallic components.

  • A Thin-Film Strain Sensor With Near-Zero Temperature Interference and High Stability

    by Mengqiu Li, Zhiyuan Hu, Jiaxiang Wang, Bo Yan, Fengming Ye, Jianwei Hou, Yangtao Yu, Yahui Li, Guifu Ding, Faheng Zang, et al.

    Strain sensors are critical for dynamic strain monitoring in fields such as bridge safety assessment, but their accuracy in variable-temperature environments is hindered by temperature interference, a key issue that limits their reliability despite demands for high sensitivity and strong antitemperature capability. Here, we develop a resistive strain sensor based on a homogeneous composite thin-film, fabricated using microelectromechanical system (MEMS) technology. The design leverages defect-free, dense, and low-roughness microstructures, as well as the balanced electron scattering mechanisms in materials with positive/negative temperature coefficient of resistance (TCR) to clarify the microscopic nature of near-zero TCR. The resulting strain sensor exhibits a near-zero TCR of –3.5ppm/°C, strong antitemperature interference, and high long-term stability with a resistance drift rate (DR) of only 0.00019/h. It also shows good linearity and repeatability in strain response. Simulated bridge vibration tests confirm its rapid, consistent response to vibrations of varying amplitudes and ability to detect low-frequency microstrains, providing an effective solution for accurate long-term strain monitoring in variable-temperature scenarios.


  • Open Access

    Design and Fabrication of Low-Threshold Inertial Switches Using Metal Droplets as Sensing Elements

    by Wenguo Chen, Jiaxu Yang, Rui Wang, Huiying Wang, Guifu Ding

    In this paper, we propose a novel design model for an inertial switch that utilizes metal droplets as the sensing element. The overall device model comprises three components: the substrate layer, the functional structure layer, and the cover layer, along with the liquid metal. The metal droplets within the liquid storage tank are drawn towards the fixed electrode due to inertial forces. When the acceleration exceeds a predetermined threshold, the metal droplet covers the fixed electrode, closing the switch and allowing current to flow through the external circuit. Conversely, when the acceleration load is removed, the metal droplet retracts to the liquid storage tank, disconnecting the fixed electrode. This design is characterized by its simplicity, low manufacturing cost, and stable dynamic response. To evaluate the threshold acceleration of the inertial switch, we developed a threshold evaluation equation through theoretical analysis and successfully fabricated an experimental prototype. Test results indicate that the threshold acceleration of the fabricated inertial switch is 0.76g, with a response time of 21 ms and a contact time of 10 ms. The overload test indicates that the device has excellent overload impact resistance and stable dynamic contact. Compared to traditional mechanical contact-type inertial switches, this research not only presents a new scheme for low-threshold inertial switches with a simple structure and low manufacturing cost, but also introduces the concept of deformable liquid metal electrodes into the field of inertial sensing for the first time, opening up a new technical path for applications such as consumer electronics and the Internet of Things that require low power consumption for triggering.

  • Open Access

    Simulation of Unidirectional Ion Ejection in Miniature Four-Channel Linear Ion Trap Array

    by Yunfan He, Zhuoqing Yang, Yan Zhang, Yunna Sun, Jinyuan Yao, Guifu Ding

    With the surging demand for dynamic, real-time, and rapid qualitative analysis of chemical components, chip-scale mass spectrometers have attracted widespread attention. Ion traps have become the preferred mass analyzer for chip-scale mass spectrometers due to their excellent analytical performance. However, the miniaturization of ion traps inevitably leads to a reduction in ion storage capacity, which in turn affects their sensitivity and dynamic range. In this study, a Miniature Four-Channel Linear Ion Trap Array (M-FLITA) with hyperbolic electrodes and a 1 mm field radius was established and optimized. Concurrently, unidirectional ion ejection was accomplished by the application of asymmetric RF voltages on M-FLITA. The results demonstrate that, in the stretched structure, the mass resolution is improved to 732, while the unidirectional ion ejection efficiency is maintained at 96%. M-FLITA demonstrates advantages in terms of high ion storage capacity and mass resolution under high ion flux conditions, providing an ideal solution for high-performance micro mass analyzers in chip-scale mass spectrometers.

  • Open Access

    An Innovative Strategy for Achieving Interface Gradient Material Using Co-Deposition Technology

    by Yanxin Zhang, Liyan Lai, Yan Luo, Zhuoqing Yang, Guifu Ding

    In this study, high-performance SiC whisker (SiCw)-reinforced Cu matrix functionally graded materials (FGMs) were achieved through the synergy of numerical simulation and co-electrodeposition and then successfully applied as the interface of Cu and Si. A comprehensive numerical simulation framework was developed to investigate the influence of gradient transition modes and the maximum volume fraction of SiCw on the thermal–mechanical properties in the different gradient structures. The optimized FGMs via numerical simulation were fabricated using a co-electrodeposition technique, producing a 100 μm thick coating with a SiCw volume fraction gradient ranging from 0% to 40%. The interface of Cu and SiC was void free in the FGMs and the SiCw was coated by nano-scale Cu grains during the electroplating process. The coefficient of thermal expansion in FGMs was higher than 9.78 × 10−6 K−1, which was the coefficient of thermal expansion in the Cu-40% vol. SiCw, and lower than 16.4 × 10−6 K−1, which was the coefficient of thermal expansion in pure Cu. Notably, the bonding interface area between the Cu/Si joint with the gradient-structured FGMs was more than twice that of non-graded materials. The enhanced thermal–mechanical performance was attributed to the synergistic effects of the nano-scale grain-reinforced SiCw-Cu interface and an optimized stress distribution achieved by the gradient structure.


  • Synergetic Optimization and In Situ Fabrication of Thin-Film Heat Flux Sensor for Heat Flux Measurement of Combustion Wind Tunnel

    by Xiangxiang Gao, Congchun Zhang, Shijia Zhang, Nan Zhao, Yi Chen, Dongyu Cui, Guifu Ding

    Instantaneous heat flux monitoring of high-temperature components in extreme environments is gaining significant attention for aircraft engines. Recently, advancements in microfabrication techniques have enabled the development of thin-film heat flux sensors (TFHFSs). However, fabricating TFHFS on complex aeroengine components, especially in narrow spaces, remains a significant challenge. In this work, the influence of geometric parameters on the sensor’s physical properties is systematically investigated using numerical simulation methods. Then, a high-temperature Pt/PtRh thermopile TFHFS is fabricated on the Ni-based turbine blade. Experimental results indicate that the proposed TFHFS exhibits a high sensitivity of 19.38 $\mu $ V/(kW/m2) and a response time of approximately 21 ms. Notably, the TFHFS has a nearly constant response in three-cycle tests and exhibits excellent repeatability and stability. Furthermore, the high-temperature combustion wind tunnel test confirms that the TFHFS can operate up to $1000~^{\circ }$ C and withstand a gas flow velocity of 0.9 Mach, indicating that the fabricated TFHFS is suitable for extremely hostile and complex environment measurement applications. This study provides a viable approach for developing various thin-film sensors on complex surfaces and promotes in situ sensing toward practical applications.


  • Research Progress of High-Temperature Thin-Film Strain Gauges: A Review

    by Nan Zhao, Yusen Wang, Congchun Zhang, Xiangxiang Gao, Ziyi Wang, Guifu Ding

    High-temperature thin-film strain gauges (HTFSGs) hold significant potential for monitoring extreme environments in fields such as aerospace, nuclear energy, and automotive engineering. With advances in materials science, HTFSGs based on ceramics, metals, and composite materials have progressively achieved high-precision strain measurements in high-temperature environments. In recent years, substantial progress has been made in areas such as material selection, sensor structural optimization, high-temperature oxidation resistance, and testing methodologies, which have enhanced the stability, sensitivity, and durability of HTFSGs under extreme conditions. This article reviews the developmental trajectory of HTFSGs research, focusing on the strain mechanisms of sensitive materials and recent advancements in ceramic-metal thin films, ceramic-semiconductor thin films, and metal-based thin films for HTFSGs in terms of structural design, thin-film deposition processes, and material properties. Additionally, current challenges and future research directions are discussed to provide valuable insights for future studies.


  • Open Access

    Advancements in the Preparation and Application of Ni-Co System (Alloys, Composites, and Coatings): A Review

    by Liyan Lai, Feng Qian, Yuxiao Bi, Bing Niu, Guanliang Yu, Yigui Li, Guifu Ding

    In the field of non-silicon MEMSs (micro-electro-mechanical systems), nickel, with its mature preparation method, good compatibility with non-silicon MEMS processes, and excellent mechanical properties, is one of the commonly used structural materials. By effectively combining it with non-silicon MEMS processes, nickel is widely used in typical process systems such as LIGA (Lithography, Galvanoformung, Abformung)/UV-LIGA (Ultraviolet Lithography, Galvanoformung, Abformung). However, with the rapid development of the non-silicon MEMS field, pure nickel materials are no longer able to meet current material demands. Alternatively, nickel–cobalt composite materials have excellent mechanical properties, thermal stability, corrosion resistance, and good adaptability to processing technology because cobalt has unique advantages as a reinforcing phase, including excellent wear resistance, corrosion resistance, and high hardness. This article examines the current methods for preparing nickel–cobalt alloys by focusing on composite electrodeposition of coatings and analyzing their advantages and disadvantages. Based on this, the effect of the composite electrodeposition conditions on the formation mechanism of nickel–cobalt alloy coatings is discussed. Then, the research status of composite electrodeposition methods mainly based on nickel–cobalt nanocomposites is discussed. Finally, a new direction for future work on nickel–cobalt composite materials mainly composed of nickel–cobalt nanomaterials prepared by composite electrodeposition is proposed, and its application prospects in non-silicon MEMS fields are discussed.