Heinrich Leicht
Heinrich Leicht has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Eduard Kraus
German Plastics Centre (SKZ)
3 shared publications Benjamin Baudrit
Joining and Surface Engineering, SKZ - KFE gGmbH, Wuerzburg, Germany
2 shared publicationsMartin Bastian
Joining and Surface Engineering, SKZ - KFE gGmbH, Wuerzburg, Germany
2 shared publicationsOleg Stoyanov
Kazan National Research Technology University Karl Marx 68, 420015 Kazan Russian Federation
2 shared publicationsThomas Hochrein
Joining and Surface Engineering, SKZ - KFE gGmbH, Wuerzburg, Germany
2 shared publications- Alesya Valer'Yevna Vurasko
Уральский государственный лесотехнический университет
1 shared publication
Latest Publications
- 28 October 2019
- Published by Taylor & Francis in The Journal of Adhesion
- Vol. 96 (1-4) , 48-63
Adhesive bonding of 3D-printed plastic components
Tensile strength of adhesive bonds with three different commercial epoxy resins and laser sintered polyamide 12 (PA 12) has been evaluated by means of Centrifugal Adhesion Testing Technology (CATT, LUMiFrac Adhesion Analyzer). Different post treatment states (as received and chemically smoothed) and pre-treatment states (as received and atmospheric plasma) of the PA 12 surface have been considered. It has been shown that the epoxy resins infiltrate the surface porosity of the laser sintered material, which leads to a special fracture pattern. Tensile strength of the adhesive bonds has been significantly improved after atmospheric plasma pretreatment. Chemical smoothing had a neglicable effect on the tensile strength of the tested specimens, but lead to a change in fracture pattern, especially without atmosphric plasma pretreatment.
- 28 October 2019
- Published by Taylor & Francis in The Journal of Adhesion
- Vol. 96 (1-4) , 48-63
Adhesive bonding of 3D-printed plastic components
Tensile strength of adhesive bonds with three different commercial epoxy resins and laser sintered polyamide 12 (PA 12) has been evaluated by means of Centrifugal Adhesion Testing Technology (CATT, LUMiFrac Adhesion Analyzer). Different post treatment states (as received and chemically smoothed) and pre-treatment states (as received and atmospheric plasma) of the PA 12 surface have been considered. It has been shown that the epoxy resins infiltrate the surface porosity of the laser sintered material, which leads to a special fracture pattern. Tensile strength of the adhesive bonds has been significantly improved after atmospheric plasma pretreatment. Chemical smoothing had a neglicable effect on the tensile strength of the tested specimens, but lead to a change in fracture pattern, especially without atmosphric plasma pretreatment.
- 22 October 2019
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 137 (16) , 48582
Structural properties of nanocomposites based on resole‐type phenol‐formaldehyde oligomers and detonation nanodiamonds
Using the methods of infrared spectroscopy (IRS) and X‐ray photoelectron spectroscopy (XPS), it was shown that short‐term high‐energy machining of detonation nanodiamonds (DND) leads to structural changes in the crystal structure and functional composition of the surface layer on particles. The possibility of spontaneous formation for stable colloidal systems with a narrow size distribution of mechanically activated DND in phenol‐formaldehyde oligomers (PFO) was established. By molecular spectroscopy it was revealed that π → π* interactions of the aromatic rings of PFO are caused by orientational phenomena as a result of hydrogen bonds between an activated DND surface and functional groups of PFO. The effect of DND concentration on the curing reaction parameters ofpsgr the phenol‐formaldehyde oligomer was determined by differential scanning calorimetry (DSC). The concentration effect of mechanically activated nanodiamonds on the physical and mechanical characteristics of a composite material based on phenol‐formaldehyde binder and polyamide paper (Nomex) was studied. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020, 137, 48582.
- 22 October 2019
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 137 (16) , 48582
Structural properties of nanocomposites based on resole‐type phenol‐formaldehyde oligomers and detonation nanodiamonds
Using the methods of infrared spectroscopy (IRS) and X‐ray photoelectron spectroscopy (XPS), it was shown that short‐term high‐energy machining of detonation nanodiamonds (DND) leads to structural changes in the crystal structure and functional composition of the surface layer on particles. The possibility of spontaneous formation for stable colloidal systems with a narrow size distribution of mechanically activated DND in phenol‐formaldehyde oligomers (PFO) was established. By molecular spectroscopy it was revealed that π → π* interactions of the aromatic rings of PFO are caused by orientational phenomena as a result of hydrogen bonds between an activated DND surface and functional groups of PFO. The effect of DND concentration on the curing reaction parameters ofpsgr the phenol‐formaldehyde oligomer was determined by differential scanning calorimetry (DSC). The concentration effect of mechanically activated nanodiamonds on the physical and mechanical characteristics of a composite material based on phenol‐formaldehyde binder and polyamide paper (Nomex) was studied. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020, 137, 48582.
- 6 September 2018
- Published by Springer Nature in adhäsion KLEBEN & DICHTEN
- Vol. 62 (9) , 40-45
Lock-in-Thermographie zur Defekterkennung in geklebten Kunststoffverbindungen
- 6 September 2018
- Published by Springer Nature in adhäsion KLEBEN & DICHTEN
- Vol. 62 (9) , 40-45
Lock-in-Thermographie zur Defekterkennung in geklebten Kunststoffverbindungen
- 1 February 2018
- Published by Elsevier in Journal of Energy Storage
- Vol. 15, 196-204
The external surface area of carbon additives as key to enhance the dynamic charge acceptance of lead-carbon electrodes
- 1 February 2018
- Published by Elsevier in Journal of Energy Storage
- Vol. 15, 196-204
The external surface area of carbon additives as key to enhance the dynamic charge acceptance of lead-carbon electrodes
- 29 September 2017
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 135 (5) , 45796
Hybrid composites based on technical cellulose from rice husk
We introduced the preparation of hybrid composites using technical cellulose as a matrix material from rice husks with a natural SiO2 content from 0% to 19.4%. In this work, the physicochemical characteristics of the resulting hybrid composites have been investigated. The presence of SiOC chemical bonds in the resulting hybrid composites was determined by infrared spectroscopy. Microscopic analysis showed the complete removal of the mineral component and lignin from the cell wall of the rice husk fibers. This allows obtaining of an expanded surface of the fibers (101.7 m2/g) with uniform distribution of the TiO2 aggregates. It could be shown that with content increasing of natural silicon dioxide in the hybrid composite the decomposition rate of H2O2 also increases. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018, 135, 45796.
- 29 September 2017
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 135 (5) , 45796
Hybrid composites based on technical cellulose from rice husk
We introduced the preparation of hybrid composites using technical cellulose as a matrix material from rice husks with a natural SiO2 content from 0% to 19.4%. In this work, the physicochemical characteristics of the resulting hybrid composites have been investigated. The presence of SiOC chemical bonds in the resulting hybrid composites was determined by infrared spectroscopy. Microscopic analysis showed the complete removal of the mineral component and lignin from the cell wall of the rice husk fibers. This allows obtaining of an expanded surface of the fibers (101.7 m2/g) with uniform distribution of the TiO2 aggregates. It could be shown that with content increasing of natural silicon dioxide in the hybrid composite the decomposition rate of H2O2 also increases. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018, 135, 45796.