Shan Fang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Shan Fang has a total of 86 co-authors. Here are the top co-authors by number of shared publications:
Xue Li
Nanchang University
8 shared publications- Stefano Passerini
Karlsruhe Institute of Technology (KIT)/Helmholtz Institute Ulm (HIU), Ulm, Germany
6 shared publications Xiang Liu
Nanchang University
6 shared publications- Naigen Zhou
Nanchang University
5 shared publications Chengjin Peng
School of Physics and Materials Science Nanchang University Nanchang Jiangxi China
4 shared publicationsFei Luo
Nanchang University
4 shared publications
Latest Publications
- 25 August 2026
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 18 (35) , 47565-47577
Fluorosulfonyl Additive-Reinforced Interphases for High-Voltage and Fast-Charging Lithium Metal Batteries
Electrolytes capable of simultaneously stabilizing lithium metal anodes and high-nickel cathodes under high-voltage and high-rate operation are essential for practical lithium metal batteries yet remain difficult to realize. Here, methyl fluorosulfonyldifluoroacetate (MDFSA) is introduced as an electrolyte additive to regulate the Li+ solvation structure in an ether–carbonate co-solvent electrolyte. MDFSA weakens the coordination of 1,2-dimethoxyethane (DME) with Li+ and promotes the involvement of DFOB– in the solvation sheath, facilitating the formation of robust inorganic-rich interphases at both the lithium metal anode and the cathode. The optimized electrolyte enables Li||LiNi0.91Co0.06Mn0.03O2 cells to deliver 75.8% capacity retention after 500 cycles at 4.5 V and 1 C and 80.53% capacity retention after 500 cycles at 4.3 V and 4 C. These results highlight the effectiveness of fluorosulfonyl additive-enabled solvation and interphase regulation for improving the high-voltage stability, rate capability, and cycling durability of lithium metal batteries.
- 25 August 2026
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 18 (35) , 47565-47577
Fluorosulfonyl Additive-Reinforced Interphases for High-Voltage and Fast-Charging Lithium Metal Batteries
Electrolytes capable of simultaneously stabilizing lithium metal anodes and high-nickel cathodes under high-voltage and high-rate operation are essential for practical lithium metal batteries yet remain difficult to realize. Here, methyl fluorosulfonyldifluoroacetate (MDFSA) is introduced as an electrolyte additive to regulate the Li+ solvation structure in an ether–carbonate co-solvent electrolyte. MDFSA weakens the coordination of 1,2-dimethoxyethane (DME) with Li+ and promotes the involvement of DFOB– in the solvation sheath, facilitating the formation of robust inorganic-rich interphases at both the lithium metal anode and the cathode. The optimized electrolyte enables Li||LiNi0.91Co0.06Mn0.03O2 cells to deliver 75.8% capacity retention after 500 cycles at 4.5 V and 1 C and 80.53% capacity retention after 500 cycles at 4.3 V and 4 C. These results highlight the effectiveness of fluorosulfonyl additive-enabled solvation and interphase regulation for improving the high-voltage stability, rate capability, and cycling durability of lithium metal batteries.
- Open Access
- 4 August 2026
- Published by Wiley in Advanced Energy Materials
- Vol. 16 (40) , e71380
Breaking the Polarity–Coordination Coupling in Electrolyte Design for High‐Voltage Lithium Batteries
Electrolyte design is fundamentally constrained by the trade‐off between high solvent polarity and weak Li + solvation, as polar solvents typically bind Li + strongly. Here, we establish a steric–electronic modulation strategy that decouples solvent polarity from Li + coordination, enabling a generalizable pseudo‐weak solvation electrolyte design paradigm. Based on this principle, a steric hindrance–mediated electrolyte is developed combining 2,2,2‐trifluoro‐N, N‐dimethylethylamide (DMTFA) and fluoroethylene carbonate (FEC) with dual lithium salts. Despite its strong polarity, DMTFA exhibits weak Li + coordination due to the combined steric hindrance and electron‐withdrawing effects of the ‐CF 3 group, enabling anion‐ dominated solvation structures. This coordination chemistry lowers Li + desolvation barriers and drives the preferential adsorption of a B‐ and P‐rich interphase layer at the cathode surface, thereby protecting the cathode from HF corrosion. The resulting electrolyte achieves high ionic conductivity, intrinsic flame retardancy, and an electrochemical stability window exceeding 5.0 V. Cells employing LiNi 0.91 Co 0.06 Mn 0.03 O 2 cathodes demonstrate a capacity retention of over 90.0% after 100 cycles at 1 C rate and 4.8 V charge cut‐off. The electrolyte enables approximately 1.6 Ah pouch cells to retain 84.97% capacity after 1800 cycles at 4.6 V.
- 4 August 2026
- Published by Wiley in Advanced Energy Materials
- Vol. 16 (40) , e71380
Open AccessBreaking the Polarity–Coordination Coupling in Electrolyte Design for High‐Voltage Lithium Batteries
Electrolyte design is fundamentally constrained by the trade‐off between high solvent polarity and weak Li + solvation, as polar solvents typically bind Li + strongly. Here, we establish a steric–electronic modulation strategy that decouples solvent polarity from Li + coordination, enabling a generalizable pseudo‐weak solvation electrolyte design paradigm. Based on this principle, a steric hindrance–mediated electrolyte is developed combining 2,2,2‐trifluoro‐N, N‐dimethylethylamide (DMTFA) and fluoroethylene carbonate (FEC) with dual lithium salts. Despite its strong polarity, DMTFA exhibits weak Li + coordination due to the combined steric hindrance and electron‐withdrawing effects of the ‐CF 3 group, enabling anion‐ dominated solvation structures. This coordination chemistry lowers Li + desolvation barriers and drives the preferential adsorption of a B‐ and P‐rich interphase layer at the cathode surface, thereby protecting the cathode from HF corrosion. The resulting electrolyte achieves high ionic conductivity, intrinsic flame retardancy, and an electrochemical stability window exceeding 5.0 V. Cells employing LiNi 0.91 Co 0.06 Mn 0.03 O 2 cathodes demonstrate a capacity retention of over 90.0% after 100 cycles at 1 C rate and 4.8 V charge cut‐off. The electrolyte enables approximately 1.6 Ah pouch cells to retain 84.97% capacity after 1800 cycles at 4.6 V.
- Open Access
- 19 March 2026
- Published by Wiley in Advanced Functional Materials
- Vol. 36 (42) , e74991
pH‐Regulated Organic–Inorganic Additive Engineering for Dendrite‐Free and Long‐Life Aqueous Zinc‐Ion Batteries
Aqueous zinc‐ion batteries (AZIBs) are promising candidates for large‐scale energy storage systems due to their inherent high safety, low cost, and environmental friendliness. However, their practical employment is hindered by dendrite growth, hydrogen evolution reaction (HER), and interfacial corrosion, which severely degrade cycling stability. This study proposes a synergistic organic–inorganic d ual additives strategy that simultaneously regulates zinc deposition, suppresses parasitic reactions, and stabilizes electrode interfaces. The organic additive nonafluorobutane‐1‐sulfonic acid (FBSA) tailors the electrolyte solvation structure, while the inorganic additive diammonium phosphate (DAP) enhances ionic conductivity and the zinc ion transference number (t + ). A pH‐regulated optimization enables the formation of a robust hybrid organic–inorganic solid electrolyte interphase (SEI) layer on the zinc anode. Moreover, this combined additive strategy disrupts the water hydrogen‐bonding network, effectively mitigating HER. Benefiting from these synergistic effects, Zn||Zn symmetric cells exhibit ultra‐stable cycling exceeding 2800 h at 5 mA cm −2 . The Zn||MnO 2 full cell maintains a capacity above 100 mAh g −1 after 1000 cycles at 1 A g −1 . This work elucidating the synergistic mechanism of organic–inorganic dual additives provides a new electrolyte design paradigm for high‐performance AZIBs.
- 19 March 2026
- Published by Wiley in Advanced Functional Materials
- Vol. 36 (42) , e74991
Open AccesspH‐Regulated Organic–Inorganic Additive Engineering for Dendrite‐Free and Long‐Life Aqueous Zinc‐Ion Batteries
Aqueous zinc‐ion batteries (AZIBs) are promising candidates for large‐scale energy storage systems due to their inherent high safety, low cost, and environmental friendliness. However, their practical employment is hindered by dendrite growth, hydrogen evolution reaction (HER), and interfacial corrosion, which severely degrade cycling stability. This study proposes a synergistic organic–inorganic d ual additives strategy that simultaneously regulates zinc deposition, suppresses parasitic reactions, and stabilizes electrode interfaces. The organic additive nonafluorobutane‐1‐sulfonic acid (FBSA) tailors the electrolyte solvation structure, while the inorganic additive diammonium phosphate (DAP) enhances ionic conductivity and the zinc ion transference number (t + ). A pH‐regulated optimization enables the formation of a robust hybrid organic–inorganic solid electrolyte interphase (SEI) layer on the zinc anode. Moreover, this combined additive strategy disrupts the water hydrogen‐bonding network, effectively mitigating HER. Benefiting from these synergistic effects, Zn||Zn symmetric cells exhibit ultra‐stable cycling exceeding 2800 h at 5 mA cm −2 . The Zn||MnO 2 full cell maintains a capacity above 100 mAh g −1 after 1000 cycles at 1 A g −1 . This work elucidating the synergistic mechanism of organic–inorganic dual additives provides a new electrolyte design paradigm for high‐performance AZIBs.
- 30 October 2025
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 17 (45) , 62228-62238
Long-Cycle Aqueous Zinc-Ion Batteries Enabled by Interfacial Engineering via Hydrogen-Bond Disruption and pH Stabilization
Aqueous zinc-ion batteries (AZIBs) offer advantages such as safety, low cost, and environmental friendliness. However, challenges such as dendrite growth, hydrogen evolution reaction (HER), and byproduct formation, i.e., zinc hydroxide sulfate (ZHS), severely limit their cycling stability and practical application. In this work, diammonium hydrogen phosphate (DAP) is introduced as a multifunctional additive to simultaneously address these challenges through three synergistic mechanisms: (1) promoting the preferential deposition of Zn2+ along the (002) crystal plane, thereby inhibiting dendrite growth; (2) disrupting the hydrogen-bonding network in aqueous media to mitigate HER; and (3) buffering local pH fluctuations to prevent ZHS precipitation. Notably, the introduction of only 0.01 M DAP significantly extends the cycling lifespan of Zn||Zn symmetric cells to 5300 h at 5 mA cm-2 and 0.5 mAh cm-2. Moreover, the Zn||MnO2 full cells achieve an exceptional capacity retention of 99.9% after 200 cycles at 1 A g-1. These findings highlight the efficacy of trace DAP addition in enhancing the electrochemical stability of AZIBs and offer a promising strategy for the development of long-life aqueous zinc-based energy storage systems.
- 30 October 2025
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 17 (45) , 62228-62238
Long-Cycle Aqueous Zinc-Ion Batteries Enabled by Interfacial Engineering via Hydrogen-Bond Disruption and pH Stabilization
Aqueous zinc-ion batteries (AZIBs) offer advantages such as safety, low cost, and environmental friendliness. However, challenges such as dendrite growth, hydrogen evolution reaction (HER), and byproduct formation, i.e., zinc hydroxide sulfate (ZHS), severely limit their cycling stability and practical application. In this work, diammonium hydrogen phosphate (DAP) is introduced as a multifunctional additive to simultaneously address these challenges through three synergistic mechanisms: (1) promoting the preferential deposition of Zn2+ along the (002) crystal plane, thereby inhibiting dendrite growth; (2) disrupting the hydrogen-bonding network in aqueous media to mitigate HER; and (3) buffering local pH fluctuations to prevent ZHS precipitation. Notably, the introduction of only 0.01 M DAP significantly extends the cycling lifespan of Zn||Zn symmetric cells to 5300 h at 5 mA cm-2 and 0.5 mAh cm-2. Moreover, the Zn||MnO2 full cells achieve an exceptional capacity retention of 99.9% after 200 cycles at 1 A g-1. These findings highlight the efficacy of trace DAP addition in enhancing the electrochemical stability of AZIBs and offer a promising strategy for the development of long-life aqueous zinc-based energy storage systems.
- Open Access
- 28 March 2025
- Published by Royal Society of Chemistry (RSC) in Energy & Environmental Science
- Vol. 18 (10) , 4740-4752
Robust interphase derived from a dual-cation ionic liquid electrolyte enabling exceptional stability for nickel-rich layered cathodes
A dual-cation-based ionic liquid electrolyte with NaPF6 additive, was designed for nickel-rich cathodes in Li-metal battery. The formed uniform and robust electrode/electrolyte interphases enables the exceptional 1500-cycle life of Li||NCM83 cells.
- 28 March 2025
- Published by Royal Society of Chemistry (RSC) in Energy & Environmental Science
- Vol. 18 (10) , 4740-4752
Open AccessRobust interphase derived from a dual-cation ionic liquid electrolyte enabling exceptional stability for nickel-rich layered cathodes
A dual-cation-based ionic liquid electrolyte with NaPF6 additive, was designed for nickel-rich cathodes in Li-metal battery. The formed uniform and robust electrode/electrolyte interphases enables the exceptional 1500-cycle life of Li||NCM83 cells.
- 19 February 2025
- Published by Royal Society of Chemistry (RSC) in Physical Chemistry Chemical Physics
- Vol. 27 (12) , 6064-6071
High energy electron beam irradiation on the electrolyte enables fast-charging of lithium metal batteries with long-term cycling stability
Electron beam (E-beam) irradiation serves as a pivotal tool within the realms of materials science, nanotechnology, and microelectronics. Its application is instrumental in altering the physical and chemical properties of materials, thereby enabling the exploration of material characteristics and fostering the advent of novel technological advancements. In this study, we irradiated the commercially available carbonate-based electrolyte LB-085 using a 10 MeV electron beam to examine the effects of electron beam (E-beam) irradiation on the electrolyte of lithium–metal batteries and explore the quantitative relationship between the absorbed radiation dose and battery's electrochemical performance. The applied absorbed radiation doses were 10, 25, and 50 kGy. Among these, the electrolyte irradiated with an absorbed radiation dose of 50 kGy effectively mitigated interfacial side reactions that occurred during the cycles of an electrode, securing a stable solid-state electrolyte interphase (SEI), which was characterized by a high ionic conductivity. This, in turn, facilitated rapid charging performance of the battery. The lithium metal full-cell assembled with LiNi0.91Co0.06Mn0.03O2 (NCM91) demonstrated superior capacity retention, exceeding 80% after 450 cycles at 4C rate (1C = 220 mA g−1, with charge times under 15 min) and also exceeding 80% after 600 cycles at 6C rate with an absorbed radiation dose of 50 kGy on the electrolyte. Thus, this research provides fresh perspectives for electrolyte optimization, focusing on enhancing the rapid charging performance of batteries.
- 19 February 2025
- Published by Royal Society of Chemistry (RSC) in Physical Chemistry Chemical Physics
- Vol. 27 (12) , 6064-6071
High energy electron beam irradiation on the electrolyte enables fast-charging of lithium metal batteries with long-term cycling stability
Electron beam (E-beam) irradiation serves as a pivotal tool within the realms of materials science, nanotechnology, and microelectronics. Its application is instrumental in altering the physical and chemical properties of materials, thereby enabling the exploration of material characteristics and fostering the advent of novel technological advancements. In this study, we irradiated the commercially available carbonate-based electrolyte LB-085 using a 10 MeV electron beam to examine the effects of electron beam (E-beam) irradiation on the electrolyte of lithium–metal batteries and explore the quantitative relationship between the absorbed radiation dose and battery's electrochemical performance. The applied absorbed radiation doses were 10, 25, and 50 kGy. Among these, the electrolyte irradiated with an absorbed radiation dose of 50 kGy effectively mitigated interfacial side reactions that occurred during the cycles of an electrode, securing a stable solid-state electrolyte interphase (SEI), which was characterized by a high ionic conductivity. This, in turn, facilitated rapid charging performance of the battery. The lithium metal full-cell assembled with LiNi0.91Co0.06Mn0.03O2 (NCM91) demonstrated superior capacity retention, exceeding 80% after 450 cycles at 4C rate (1C = 220 mA g−1, with charge times under 15 min) and also exceeding 80% after 600 cycles at 6C rate with an absorbed radiation dose of 50 kGy on the electrolyte. Thus, this research provides fresh perspectives for electrolyte optimization, focusing on enhancing the rapid charging performance of batteries.
- 8 November 2024
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 16 (46) , 63628-63637
Difluorobenzene as an Antisolvent for Fluorinated Electrolyte to Achieve Unparalleled Cycle Life of Lithium Metal Battery
Electrolytes play a crucial role in enhancing the cycling stability and overall lifespan of lithium metal batteries (LMBs). However, conventional electrolytes achieve ununiform and low ionic conductivity solid electrolyte interphase (SEI), leading to uncontrolled lithium dendrite growth and dead lithium formation, rendering them inadequate for meeting the performance of high energy density LMBs. Herein, a 1,2-difluorobenzene (1,2-dFBn) is introduced as antisolvent in fluorinated electrolyte which is composed of fluoroethylene carbonate (FEC) and lithium bis(trifluoromethanesulfonyl)imide (LiTFSI). The low energy level of the lowest unoccupied molecular orbital (LUMO) and the high fluorine-donating ability of 1,2-dFBn jointly modify the solvation structure and electrode/electrolyte interphase chemistry. As a result, this simple electrolyte formulation enables the Li||Li symmetric cells exhibit remarkable stability, enduring 700 h of continuous cycling under 2 mA cm-2 and Li||Cu cell achieve an impressive average Coulombic efficiency (CE) of 99.76%. Moreover, the full cell assembled with electrochemically deposited lithium capacity of 5 mAh cm-2 and LiFePO4 (LFP) as cathode achieves exceptional performance, maintaining a discharge specific capacity of 134.9 mAh g-1 while retaining 95.1% capacity at 2C after 1000 cycles. This study offers a plausible ratio design for fluorinated electrolyte, which achieving high CE and long-life LMBs.
- 8 November 2024
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 16 (46) , 63628-63637
Difluorobenzene as an Antisolvent for Fluorinated Electrolyte to Achieve Unparalleled Cycle Life of Lithium Metal Battery
Electrolytes play a crucial role in enhancing the cycling stability and overall lifespan of lithium metal batteries (LMBs). However, conventional electrolytes achieve ununiform and low ionic conductivity solid electrolyte interphase (SEI), leading to uncontrolled lithium dendrite growth and dead lithium formation, rendering them inadequate for meeting the performance of high energy density LMBs. Herein, a 1,2-difluorobenzene (1,2-dFBn) is introduced as antisolvent in fluorinated electrolyte which is composed of fluoroethylene carbonate (FEC) and lithium bis(trifluoromethanesulfonyl)imide (LiTFSI). The low energy level of the lowest unoccupied molecular orbital (LUMO) and the high fluorine-donating ability of 1,2-dFBn jointly modify the solvation structure and electrode/electrolyte interphase chemistry. As a result, this simple electrolyte formulation enables the Li||Li symmetric cells exhibit remarkable stability, enduring 700 h of continuous cycling under 2 mA cm-2 and Li||Cu cell achieve an impressive average Coulombic efficiency (CE) of 99.76%. Moreover, the full cell assembled with electrochemically deposited lithium capacity of 5 mAh cm-2 and LiFePO4 (LFP) as cathode achieves exceptional performance, maintaining a discharge specific capacity of 134.9 mAh g-1 while retaining 95.1% capacity at 2C after 1000 cycles. This study offers a plausible ratio design for fluorinated electrolyte, which achieving high CE and long-life LMBs.
- 24 April 2024
- Published by Elsevier in Journal of Power Sources
- Vol. 606
Bulk doping of tungsten improves the structure stability and electrochemical performance of layered Ni-rich material
- 24 April 2024
- Published by Elsevier in Journal of Power Sources
- Vol. 606
Bulk doping of tungsten improves the structure stability and electrochemical performance of layered Ni-rich material