Zoubir Acem
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Zoubir Acem has a total of 107 co-authors. Here are the top co-authors by number of shared publications:
- Gilles Parent
Lab. d'Energétique et de Mécanique Théorique et Appliquée (France)
15 shared publications P. Boulet
11 shared publications- Anthony Collin
LEMTA, Laboratoire d’Energétique et de Mécanique Théorique et Appliquée, Université de Lorraine, UMR 7563, CNRS, F-54500 Vandœuvre-lès-Nancy, France
6 shared publications A. Collin
Université de Lorraine, CNRS, LEMTA, Nancy, France
5 shared publicationsPascal Boulet
5 shared publications- Pascal Boulet
LEMTA, CNRS, Université de Lorraine, Nancy, France
5 shared publications
Latest Publications
- Open Access
- 6 December 2024
- Published by Elsevier in International Journal of Thermal Sciences
- Vol. 210
Study of heat transfer in wood before the onset of pyrolysis at the cone calorimeter scale
- 6 December 2024
- Published by Elsevier in International Journal of Thermal Sciences
- Vol. 210
Open AccessStudy of heat transfer in wood before the onset of pyrolysis at the cone calorimeter scale
- 27 July 2024
- Published by Springer Nature in Fire Technology
- Vol. 61 (2) , 363-379
Water Sprays Cooling of a Hot Metallic Plate
- 27 July 2024
- Published by Springer Nature in Fire Technology
- Vol. 61 (2) , 363-379
Water Sprays Cooling of a Hot Metallic Plate
- 1 February 2020
- Published by Elsevier in International Journal of Thermal Sciences
- Vol. 148
Use of a water mist for smoke confinement and radiation shielding in case of fire during tunnel construction
- 1 February 2020
- Published by Elsevier in International Journal of Thermal Sciences
- Vol. 148
Use of a water mist for smoke confinement and radiation shielding in case of fire during tunnel construction
- 1 October 2019
- Published by Elsevier in Fire Safety Journal
- Vol. 109
Vegetation fire spread database: 85 wood wool shaving experiments at laboratory scale
- 1 October 2019
- Published by Elsevier in Fire Safety Journal
- Vol. 109
Vegetation fire spread database: 85 wood wool shaving experiments at laboratory scale
- 1 September 2019
- Published by Elsevier in Fire Safety Journal
- Vol. 108
Experimental tools applied to ignition study of spruce wood under cone calorimeter
- 1 September 2019
- Published by Elsevier in Fire Safety Journal
- Vol. 108
Experimental tools applied to ignition study of spruce wood under cone calorimeter
- Open Access
- 14 November 2018
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1107 (3) , 032022
Experimental tools applied to the ignition study of spruce wood under cone calorimeter
Wood-based materials, which are more and more used in building construction, are often characterized by normative tests using the cone calorimeter. The ignition time and temperature, the mass loss rate or heat release rate are the most current measurements performed. The sample ignition can vary according to a large number of variables (humidity, density, scale sample, experimental conditions). The auto ignition phenomenon has been studied so far but opinions concerning the involved physical processes remain controversial. The purpose of the present work is to improve the study of thermal degradation of wood under cone calorimeter thanks to a dedicated experimental set up. This set up includes mainly, an infrared camera, enabling an accurate surface temperature measurement and a fast visible camera (3000 fps), used to highlight the "auto" ignition phenomenon. Surface temperature and mass loss rate evolution are presented for different heat flux expositions. The fast visible camera pictures showed an ignition piloted by the coil. The ignition occurs only above 55 kW.m−2. When this external heat flux was sufficiently low, it was possible to observe the transition between pyrolysis solely and smouldering combustion for a sample surface temperature around 400 ° C.
- 14 November 2018
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1107 (3) , 032022
Open AccessExperimental tools applied to the ignition study of spruce wood under cone calorimeter
Wood-based materials, which are more and more used in building construction, are often characterized by normative tests using the cone calorimeter. The ignition time and temperature, the mass loss rate or heat release rate are the most current measurements performed. The sample ignition can vary according to a large number of variables (humidity, density, scale sample, experimental conditions). The auto ignition phenomenon has been studied so far but opinions concerning the involved physical processes remain controversial. The purpose of the present work is to improve the study of thermal degradation of wood under cone calorimeter thanks to a dedicated experimental set up. This set up includes mainly, an infrared camera, enabling an accurate surface temperature measurement and a fast visible camera (3000 fps), used to highlight the "auto" ignition phenomenon. Surface temperature and mass loss rate evolution are presented for different heat flux expositions. The fast visible camera pictures showed an ignition piloted by the coil. The ignition occurs only above 55 kW.m−2. When this external heat flux was sufficiently low, it was possible to observe the transition between pyrolysis solely and smouldering combustion for a sample surface temperature around 400 ° C.
- 8 November 2017
- Published by Wiley in Fire and Materials
- Vol. 42 (3) , 247-254
Experimental and numerical study of interactions between sprinklers and natural smoke vents
Real scale experimentations have been conducted in order to investigate interactions that may occur in a compartment where sprinklers and Smoke and Heat Exhaust Vent Systems coexist. Fuel oil spray was used as fire source with steady heat release rate of 400 and 800 kW. Both sprinkler system and natural Smoke and Heat Exhaust Vent Systems were designed according to the French standards. Effect of vent on sprinkler activation time was studied. An analysis of the temperature field inside the compartment was conducted while vent was opened prior or after sprinkler activation. Simulations of the experiments were also carried out with Fire Dynamics Simulator v.6 for validation purpose and also to provide supplementary data regarding soot flow rate and energy extracted at the vent.
- 8 November 2017
- Published by Wiley in Fire and Materials
- Vol. 42 (3) , 247-254
Experimental and numerical study of interactions between sprinklers and natural smoke vents
Real scale experimentations have been conducted in order to investigate interactions that may occur in a compartment where sprinklers and Smoke and Heat Exhaust Vent Systems coexist. Fuel oil spray was used as fire source with steady heat release rate of 400 and 800 kW. Both sprinkler system and natural Smoke and Heat Exhaust Vent Systems were designed according to the French standards. Effect of vent on sprinkler activation time was studied. An analysis of the temperature field inside the compartment was conducted while vent was opened prior or after sprinkler activation. Simulations of the experiments were also carried out with Fire Dynamics Simulator v.6 for validation purpose and also to provide supplementary data regarding soot flow rate and energy extracted at the vent.
- 1 February 2017
- Published by Elsevier in International Journal of Thermal Sciences
- Vol. 112, 427-438
Surface temperature of carbon composite samples during thermal degradation
- 1 February 2017
- Published by Elsevier in International Journal of Thermal Sciences
- Vol. 112, 427-438
Surface temperature of carbon composite samples during thermal degradation
- 11 January 2017
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 51 (22) , 3137-3147
Effect of a coupled thermomechanical loading on the residual mechanical strength and on the surface temperature of wound carbon/epoxy composite
Wound composite structures such as hyperbaric hydrogen tanks may experience accidental situations, for example in case of a fire. The FCH-JU project FireComp aims at better characterizing the conditions that need to be achieved in order to avoid a failure of a composite pressure vessel. This research program involves specific experiments to improve the understanding of loss of strength of composite high-pressure vessels in fire conditions. The present study investigates the effect of a coupled thermomechanical loading (cone calorimeter exposure and, simultaneously, mechanical stress) on the residual strength of a composite material. A specific device combining a cone and a four-point bending bench has been designed. The influence of the coupled aggression is addressed by comparing the temperature on the front and the rear sides, the mass loss, and the residual tensile strength of a set of samples subjected to a heat flux only and a set subjected to a heat flux and a four-point bending. The results do not exhibit a clear effect of the mechanical load: the thermomechanical properties of both sets of samples are similar.
- 11 January 2017
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 51 (22) , 3137-3147
Effect of a coupled thermomechanical loading on the residual mechanical strength and on the surface temperature of wound carbon/epoxy composite
Wound composite structures such as hyperbaric hydrogen tanks may experience accidental situations, for example in case of a fire. The FCH-JU project FireComp aims at better characterizing the conditions that need to be achieved in order to avoid a failure of a composite pressure vessel. This research program involves specific experiments to improve the understanding of loss of strength of composite high-pressure vessels in fire conditions. The present study investigates the effect of a coupled thermomechanical loading (cone calorimeter exposure and, simultaneously, mechanical stress) on the residual strength of a composite material. A specific device combining a cone and a four-point bending bench has been designed. The influence of the coupled aggression is addressed by comparing the temperature on the front and the rear sides, the mass loss, and the residual tensile strength of a set of samples subjected to a heat flux only and a set subjected to a heat flux and a four-point bending. The results do not exhibit a clear effect of the mechanical load: the thermomechanical properties of both sets of samples are similar.