Alexey Yurikov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Alexey Yurikov has a total of 45 co-authors. Here are the top co-authors by number of shared publications:
- Maxim Lebedev
Curtin University
9 shared publications - Roman Pevzner
Centre for Exploration Geophysics, Curtin University, GPO Box U1987, Perth, WA 6845, Australia
8 shared publications - Boris Gurevich
Curtin University, Perth, Australia
7 shared publications - Konstantin Tertyshnikov
Centre for Exploration Geophysics, Curtin University, GPO Box U1987, Perth, WA 6845, Australia
7 shared publications - Roman Isaenkov
Centre for Exploration Geophysics, Curtin University, GPO Box U1987, Perth, WA 6845, Australia
6 shared publications - Sinem Yavuz
Curtin University
6 shared publications
Latest Publications
- Open Access
3D DAS VSP for Coal Seam Exploration: A Case Study from Queensland, Australia
Seismic methods are extensively used in coal mining for expanding resource discoveries and definition as well as for mine monitoring. However, the use of borehole seismic methods is relatively uncommon due to the high cost of borehole seismic acquisition using conventional downhole tools. The introduction of distributed acoustic sensing (DAS), which uses optical fibres to record seismic data, has dramatically increased the cost-effectiveness of borehole seismic methods. Fibre-optic cables are inexpensive and, once deployed in a borehole, can be abandoned or used later for further monitoring of the subsurface. The case study presented here concerns the use of DAS to record a 3D VSP (vertical seismic profiling) for coal seam exploration in Queensland, Australia. This study trialled effective strategies for deploying cables into boreholes and demonstrated how this technology could be incorporated into the standard coal exploration process. The final processing results produced a high-resolution 3D seismic cube where the coal seams below the basalt cover are clearly identifiable around the boreholes. Permanent installation of the fibre-optic cables into a set of boreholes provides immediate benefits of 3D seismic imaging and can create additional value in utilising these sensors for further discrete or continuous subsurface measurements, including stability monitoring of underground workings and detection of methane accumulations.
Open Access3D DAS VSP for Coal Seam Exploration: A Case Study from Queensland, Australia
Seismic methods are extensively used in coal mining for expanding resource discoveries and definition as well as for mine monitoring. However, the use of borehole seismic methods is relatively uncommon due to the high cost of borehole seismic acquisition using conventional downhole tools. The introduction of distributed acoustic sensing (DAS), which uses optical fibres to record seismic data, has dramatically increased the cost-effectiveness of borehole seismic methods. Fibre-optic cables are inexpensive and, once deployed in a borehole, can be abandoned or used later for further monitoring of the subsurface. The case study presented here concerns the use of DAS to record a 3D VSP (vertical seismic profiling) for coal seam exploration in Queensland, Australia. This study trialled effective strategies for deploying cables into boreholes and demonstrated how this technology could be incorporated into the standard coal exploration process. The final processing results produced a high-resolution 3D seismic cube where the coal seams below the basalt cover are clearly identifiable around the boreholes. Permanent installation of the fibre-optic cables into a set of boreholes provides immediate benefits of 3D seismic imaging and can create additional value in utilising these sensors for further discrete or continuous subsurface measurements, including stability monitoring of underground workings and detection of methane accumulations.
- Open Access
- 8 June 2023
- Published by Elsevier in Journal of Rock Mechanics and Geotechnical Engineering
- Vol. 15 (9) , 2330-2338
Low-frequency laboratory measurements of the elastic properties of solids using a distributed acoustic sensing system
- 8 June 2023
- Published by Elsevier in Journal of Rock Mechanics and Geotechnical Engineering
- Vol. 15 (9) , 2330-2338
Open AccessLow-frequency laboratory measurements of the elastic properties of solids using a distributed acoustic sensing system
- Open Access
Effect of Source Mispositioning on the Repeatability of 4D Vertical Seismic Profiling Acquired with Distributed Acoustic Sensors
Vertical seismic profiling (VSP) with distributed acoustic sensing (DAS) is an increasingly popular evolving technique for reservoir monitoring. DAS technology enables permanent fibre installations in wells and simultaneous seismic data recording along an entire borehole. Deploying the receivers closer to the reservoir allows for better detectability of smaller signals. A high level of repeatability is essential for the robust time-lapse monitoring of geological reservoirs. One of the prominent factors of repeatability degradation is a shift between source/receiver locations (mispositioning) during baseline and monitor surveys. While the mispositioning effect has been extensively studied for surface 4D seismic, the number of such studies for VSP is quite limited. To study the effects of source mispositioning on time-lapse data repeatability, we performed two VSP experiments at two on-shore sites with vibroseis. The first study was carried out at the Otway International Test Centre during Stage 3 of the Otway project and showed that the effect of source mispositioning on repeatability is negligible in comparison with the effect of temporal variations of the near-surface conditions. To avoid these limitations, we conducted a same-day controlled experiment at the Curtin University site. This second experiment showed that the effect of source mispositioning on repeatability is controlled by the degree of lateral variations of the near-surface conditions. Unlike in marine seismic measurements, lateral variations of near-surface properties can be strong and rapid and can degrade the repeatability for shifts of the source of a few meters. The greater the mispositioning, the higher the chance of such significant variations. When the near-surface conditions are laterally homogeneous, the effect of typical source mispositioning is small, and in all practical monitoring applications its contribution to non-repeatability is negligible.
Open AccessEffect of Source Mispositioning on the Repeatability of 4D Vertical Seismic Profiling Acquired with Distributed Acoustic Sensors
Vertical seismic profiling (VSP) with distributed acoustic sensing (DAS) is an increasingly popular evolving technique for reservoir monitoring. DAS technology enables permanent fibre installations in wells and simultaneous seismic data recording along an entire borehole. Deploying the receivers closer to the reservoir allows for better detectability of smaller signals. A high level of repeatability is essential for the robust time-lapse monitoring of geological reservoirs. One of the prominent factors of repeatability degradation is a shift between source/receiver locations (mispositioning) during baseline and monitor surveys. While the mispositioning effect has been extensively studied for surface 4D seismic, the number of such studies for VSP is quite limited. To study the effects of source mispositioning on time-lapse data repeatability, we performed two VSP experiments at two on-shore sites with vibroseis. The first study was carried out at the Otway International Test Centre during Stage 3 of the Otway project and showed that the effect of source mispositioning on repeatability is negligible in comparison with the effect of temporal variations of the near-surface conditions. To avoid these limitations, we conducted a same-day controlled experiment at the Curtin University site. This second experiment showed that the effect of source mispositioning on repeatability is controlled by the degree of lateral variations of the near-surface conditions. Unlike in marine seismic measurements, lateral variations of near-surface properties can be strong and rapid and can degrade the repeatability for shifts of the source of a few meters. The greater the mispositioning, the higher the chance of such significant variations. When the near-surface conditions are laterally homogeneous, the effect of typical source mispositioning is small, and in all practical monitoring applications its contribution to non-repeatability is negligible.
- Open Access
Comparison of Amplitude Measurements on Borehole Geophone and DAS Data
DAS and geophones are the two most popular sensors for borehole seismic acquisition. As such, it is important to get a good understanding of how these two types of sensors compare to each other. The natural measurand for the techniques is different; millivolts are approximately proportional to particle velocities for geophones vs. changes in the phase of light linked to the changes in strain on the sensing fibre. This paper focuses on the experimental comparison of absolute values of these measurands derived from a VSP survey acquired in Curtin GeoLab training well. We describe the acquisition setup for the walk-away VSP acquired with DAS and geophones, allowing the direct comparison and the workflow, which we can use to represent the data in strain rate. Albeit this is unlikely to be universal, we find that the absolute values are similar for this experimental setup.
Open AccessComparison of Amplitude Measurements on Borehole Geophone and DAS Data
DAS and geophones are the two most popular sensors for borehole seismic acquisition. As such, it is important to get a good understanding of how these two types of sensors compare to each other. The natural measurand for the techniques is different; millivolts are approximately proportional to particle velocities for geophones vs. changes in the phase of light linked to the changes in strain on the sensing fibre. This paper focuses on the experimental comparison of absolute values of these measurands derived from a VSP survey acquired in Curtin GeoLab training well. We describe the acquisition setup for the walk-away VSP acquired with DAS and geophones, allowing the direct comparison and the workflow, which we can use to represent the data in strain rate. Albeit this is unlikely to be universal, we find that the absolute values are similar for this experimental setup.
- Open Access
Evidence of Nonlinear Seismic Effects in the Earth from Downhole Distributed Acoustic Sensors
Seismic velocities and elastic moduli of rocks are known to vary significantly with applied stress, which indicates that these materials exhibit nonlinear elasticity. Monochromatic waves in nonlinear elastic media are known to generate higher harmonics and combinational frequencies. Such effects have the potential to be used for broadening the frequency band of seismic sources, characterization of the subsurface, and safety monitoring of civil engineering infrastructure. However, knowledge on nonlinear seismic effects is still scarce, which impedes the development of their practical applications. To explore the potential of nonlinear seismology, we performed three experiments: two in the field and one in the laboratory. The first field experiment used two vibroseis sources generating signals with two different monochromatic frequencies. The second field experiment used a surface orbital vibrator with two eccentric motors working at different frequencies. In both experiments, the generated wavefield was recorded in a borehole using a fiber-optic distributed acoustic sensing cable. Both experiments showed combinational frequencies, harmonics, and other intermodulation products of the fundamental frequencies both on the surface and at depth. Laboratory experiments replicated the setup of the field test with vibroseis sources and showed similar nonlinear combinations of fundamental frequencies. Amplitudes of the nonlinear signals observed in the laboratory showed variation with the saturating fluid. These results confirm that nonlinear components of the wavefield propagate as body waves, are likely to generate within rock formations, and can be potentially used for reservoir fluid characterization.
Open AccessEvidence of Nonlinear Seismic Effects in the Earth from Downhole Distributed Acoustic Sensors
Seismic velocities and elastic moduli of rocks are known to vary significantly with applied stress, which indicates that these materials exhibit nonlinear elasticity. Monochromatic waves in nonlinear elastic media are known to generate higher harmonics and combinational frequencies. Such effects have the potential to be used for broadening the frequency band of seismic sources, characterization of the subsurface, and safety monitoring of civil engineering infrastructure. However, knowledge on nonlinear seismic effects is still scarce, which impedes the development of their practical applications. To explore the potential of nonlinear seismology, we performed three experiments: two in the field and one in the laboratory. The first field experiment used two vibroseis sources generating signals with two different monochromatic frequencies. The second field experiment used a surface orbital vibrator with two eccentric motors working at different frequencies. In both experiments, the generated wavefield was recorded in a borehole using a fiber-optic distributed acoustic sensing cable. Both experiments showed combinational frequencies, harmonics, and other intermodulation products of the fundamental frequencies both on the surface and at depth. Laboratory experiments replicated the setup of the field test with vibroseis sources and showed similar nonlinear combinations of fundamental frequencies. Amplitudes of the nonlinear signals observed in the laboratory showed variation with the saturating fluid. These results confirm that nonlinear components of the wavefield propagate as body waves, are likely to generate within rock formations, and can be potentially used for reservoir fluid characterization.
- 1 September 2021
- Published by Society of Exploration Geophysicists in The Leading Edge
- Vol. 40 (9) , 655-661
Laboratory measurements with DAS: A fast and sensitive tool to obtain elastic properties at seismic frequencies
Forced-oscillation stress-strain laboratory measurements are increasingly employed to obtain elastic and viscoelastic properties of rocks at seismic frequencies. Yet these measurements are time-consuming and expensive, due in part to the use of metal or semiconductor strain gauges, which need to be glued to the sample. Such gauges are fragile, have relatively low sensitivity, and measure very local strain only so the measurements can be affected by a slight misalignment of the system assembly and local heterogeneity of the rock. The emergence of fiber-optic distributed acoustic sensing (DAS) technology provides an alternative means of measuring strain. Strain measurements with DAS involve winding an optical fiber around the sample multiple times and connecting it to a DAS recording unit. Pilot experiments performed using this setup on a range of rocks and materials show good agreement with strain gauge measurements. Advantages of DAS over strain gauges include much higher strain sensitivity (down to 10−11) and signal-to-noise ratio (and hence, shorter time required for measurements), larger dynamic range, ability to measure average (rather than local) strain in the sample, and robustness at elevated temperatures. Although the pilot experiments demonstrate the potential of DAS for rock physics measurements, further research and improvement of the proposed methodology are required to obtain independent estimates of Young's modulus and Poisson's ratio and to port the system into a pressure vessel to obtain rock properties under in-situ conditions.
- 1 September 2021
- Published by Society of Exploration Geophysicists in The Leading Edge
- Vol. 40 (9) , 655-661
Laboratory measurements with DAS: A fast and sensitive tool to obtain elastic properties at seismic frequencies
Forced-oscillation stress-strain laboratory measurements are increasingly employed to obtain elastic and viscoelastic properties of rocks at seismic frequencies. Yet these measurements are time-consuming and expensive, due in part to the use of metal or semiconductor strain gauges, which need to be glued to the sample. Such gauges are fragile, have relatively low sensitivity, and measure very local strain only so the measurements can be affected by a slight misalignment of the system assembly and local heterogeneity of the rock. The emergence of fiber-optic distributed acoustic sensing (DAS) technology provides an alternative means of measuring strain. Strain measurements with DAS involve winding an optical fiber around the sample multiple times and connecting it to a DAS recording unit. Pilot experiments performed using this setup on a range of rocks and materials show good agreement with strain gauge measurements. Advantages of DAS over strain gauges include much higher strain sensitivity (down to 10−11) and signal-to-noise ratio (and hence, shorter time required for measurements), larger dynamic range, ability to measure average (rather than local) strain in the sample, and robustness at elevated temperatures. Although the pilot experiments demonstrate the potential of DAS for rock physics measurements, further research and improvement of the proposed methodology are required to obtain independent estimates of Young's modulus and Poisson's ratio and to port the system into a pressure vessel to obtain rock properties under in-situ conditions.
- 20 August 2021
- Published by Wiley in Geophysical Prospecting
- Vol. 69 (8-9) , 1664-1677
Processing of multi‐well offset vertical seismic profile data acquired with distributed acoustic sensors and surface orbital vibrators: Stage 3 of the CO2CRC Otway Project case study
Time‐lapse seismic reservoir monitoring is used as a way to gain insight into subsurface processes. Yet, the application of standard 4D technology onshore faces challenges, such as high cost, significant environmental footprint and, consequently, relatively infrequent surveys. As part of the Otway Project Stage 3 CO2 injection study, continuous automated borehole‐based monitoring using distributed acoustic sensing has been paired with permanently deployed surface sources, referred to as surface orbital vibrators, as a way to monitor the spreading CO2 plume. The injection of 15,000 tonnes of CO2 in a saline reservoir at a depth of 1550 m is monitored using five boreholes instrumented with enhanced sensitivity fibre optic cables and nine surface orbital vibrators, creating an array of 45 well–source pairs. The data are processed with an offset vertical seismic profiling processing workflow developed to address key challenges of the continuous distributed acoustic sensing acquisition using surface orbital vibrators. The processing flow includes deconvolution with a source sweep recorded by a pilot geophone installed below the surface orbital vibrators. A second deconvolution with a wavelet estimated from direct arrivals compensates for the difference between distributed acoustic sensing measurements and the pilot geophone as well as near‐surface variations. Image quality is noted to be best for short offsets and decreases with increasing offsets and well deviations. As surface orbital vibrators generate unique sweeps in two rotation directions, further processing is applied to stack these rotation signals together, which further improves the images. The resulting 2D transects of each well–source pair visually provide good illumination of the subsurface, suggesting continuous monitoring of the spreading CO2 plume should be possible with some further tuning of the processing workflow for time‐lapse repeatability.
- 20 August 2021
- Published by Wiley in Geophysical Prospecting
- Vol. 69 (8-9) , 1664-1677
Processing of multi‐well offset vertical seismic profile data acquired with distributed acoustic sensors and surface orbital vibrators: Stage 3 of the CO2CRC Otway Project case study
Time‐lapse seismic reservoir monitoring is used as a way to gain insight into subsurface processes. Yet, the application of standard 4D technology onshore faces challenges, such as high cost, significant environmental footprint and, consequently, relatively infrequent surveys. As part of the Otway Project Stage 3 CO2 injection study, continuous automated borehole‐based monitoring using distributed acoustic sensing has been paired with permanently deployed surface sources, referred to as surface orbital vibrators, as a way to monitor the spreading CO2 plume. The injection of 15,000 tonnes of CO2 in a saline reservoir at a depth of 1550 m is monitored using five boreholes instrumented with enhanced sensitivity fibre optic cables and nine surface orbital vibrators, creating an array of 45 well–source pairs. The data are processed with an offset vertical seismic profiling processing workflow developed to address key challenges of the continuous distributed acoustic sensing acquisition using surface orbital vibrators. The processing flow includes deconvolution with a source sweep recorded by a pilot geophone installed below the surface orbital vibrators. A second deconvolution with a wavelet estimated from direct arrivals compensates for the difference between distributed acoustic sensing measurements and the pilot geophone as well as near‐surface variations. Image quality is noted to be best for short offsets and decreases with increasing offsets and well deviations. As surface orbital vibrators generate unique sweeps in two rotation directions, further processing is applied to stack these rotation signals together, which further improves the images. The resulting 2D transects of each well–source pair visually provide good illumination of the subsurface, suggesting continuous monitoring of the spreading CO2 plume should be possible with some further tuning of the processing workflow for time‐lapse repeatability.
- 4 August 2021
- Published by Society of Exploration Geophysicists in Geophysics
- Vol. 86 (6) , D241-D248
Multiwell 3D distributed acoustic sensing vertical seismic profile imaging with engineered fibers: CO2CRC Otway Project case study
The 4D surface seismic monitoring is a standard method for reservoir surveillance during the production of hydrocarbons or CO2 injection. However, land 4D seismic acquisition campaigns are often associated with high cost and disruptions to industrial operation or agricultural activities in the area of acquisition. An alternative technique for time-lapse monitoring of the subsurface is the 3D vertical seismic profiling (VSP), which becomes particularly attractive when used with distributed acoustic fiber-optic sensors (DAS) installed in wells. The advantages of 3D DAS VSP include its relatively low cost, minimal footprint on the local area during acquisition, and superior spatial resolution compared to the resolution of geophones. The potential of this technique is explored by processing and analyzing multiwell 3D DAS VSP data acquired at the CO2CRC Otway Project site in Victoria, Australia. The DAS data were recorded using an engineered fiber with enhanced backscattering cemented behind the casing of five wells. The data from each well are processed individually using the same processing flow and then migrated using a 3D migration code tailored to DAS data. Having DAS along the full extent of multiple wells ensures adequate seismic coverage of the area of CO2 injection. The migrated images provide detailed information about the subsurface up to 700 m away from a well and up to 2 km depth. The images are consistent with previously acquired geophone VSP and surface seismic data. The quality of the 3D DAS VSP imaging is comparable or superior to the quality of conventional imaging using geophone data. Therefore, 3D DAS VSP is a demonstrably optimal solution for reservoir monitoring.
- 4 August 2021
- Published by Society of Exploration Geophysicists in Geophysics
- Vol. 86 (6) , D241-D248
Multiwell 3D distributed acoustic sensing vertical seismic profile imaging with engineered fibers: CO2CRC Otway Project case study
The 4D surface seismic monitoring is a standard method for reservoir surveillance during the production of hydrocarbons or CO2 injection. However, land 4D seismic acquisition campaigns are often associated with high cost and disruptions to industrial operation or agricultural activities in the area of acquisition. An alternative technique for time-lapse monitoring of the subsurface is the 3D vertical seismic profiling (VSP), which becomes particularly attractive when used with distributed acoustic fiber-optic sensors (DAS) installed in wells. The advantages of 3D DAS VSP include its relatively low cost, minimal footprint on the local area during acquisition, and superior spatial resolution compared to the resolution of geophones. The potential of this technique is explored by processing and analyzing multiwell 3D DAS VSP data acquired at the CO2CRC Otway Project site in Victoria, Australia. The DAS data were recorded using an engineered fiber with enhanced backscattering cemented behind the casing of five wells. The data from each well are processed individually using the same processing flow and then migrated using a 3D migration code tailored to DAS data. Having DAS along the full extent of multiple wells ensures adequate seismic coverage of the area of CO2 injection. The migrated images provide detailed information about the subsurface up to 700 m away from a well and up to 2 km depth. The images are consistent with previously acquired geophone VSP and surface seismic data. The quality of the 3D DAS VSP imaging is comparable or superior to the quality of conventional imaging using geophone data. Therefore, 3D DAS VSP is a demonstrably optimal solution for reservoir monitoring.