Ruth Anayimi Lafia-Araga
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Ruth Anayimi Lafia-Araga has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
Aziz Hassan
Polymer and Composite Materials Research Laboratory, Department of Chemistry, Faculty of Science, University of Malaya, Kuala Lumpur, Malaysia
3 shared publicationsRosiyah Yahya
Polymer and Composite Materials Research Laboratory, Department of Chemistry, Faculty of Science, University of Malaya, Kuala Lumpur, Malaysia
3 shared publications- Ganiyat Olusola Adebayo
Polymer and Composite Materials Research Laboratory, Department of Chemistry, Faculty of Science, University of Malaya, Kuala Lumpur, Malaysia
2 shared publications Normasmira Abd Rahman
Polymer and Composite Materials Research Laboratory, Department of Chemistry, Faculty of Science, University of Malaya, Kuala Lumpur, Malaysia
2 shared publications- Aziz Hassan
Department of Chemistry, Faculty of Science, University of Malaya, Kuala Lumpur, Malaysia
1 shared publication Blessing A. C. Enwere
Department of Chemistry, Federal College of Education, Zuba, Federal Capital Territory, Abuja Nigeria
1 shared publication
Latest Publications
- Open Access
- 31 December 2020
- Published by Univ. of Malaya in International STEM Journal
- Vol. 1 (1) , 47-58
THERMAL DEGRADATION PROFILE OF CHEMICALLY MODIFIED WOOD SAWDUST
Gmelina arborea sawdust was chemically modified using 4% and 8% concentrations of NaOH solution for 30 and 90 minutes soaking times. The influence of this modification on the chemical composition and thermal properties of samples were investigated. Chemical characterization of samples revealed that the percentage content of hemicellulose decreased from 24.5% in the unmodified sample to 20.8%, 17.6% and 15.2% in samples soaked in 4% NaOH solution for 90 minutes, 8% NaOH for 30 and 90 minutes respectively. The amount of lignin decreased from 25.0% in unmodified samples to 19.0% when the sample was treated with 8% NaOH for 90 minutes. A moisture content of 9.0% and 2.5% were recorded in unmodified and sample treated with 8% NaOH for 90 minutes respectively. However, the cellulose content increased from 38.1% in unmodified sample to 60.1% when the sample was treated with 8% NaOH for 90 minutes. The percentage weight loss increased as concentration and modification time increased. Functional groups analysis by Fourier Transform Infrared Spectroscopy (FTIR) showed evidence of reduction in OH and removal of C=O groups associated with the wood polymers after chemical modification. Thermogravimetric analysis revealed that samples treated with 4% NaOH for 90 minutes presented the highest onset and peak degradation temperatures of 274.0°C and 372.1°C respectively. From these results, it can be concluded that modification with 4% NaOH solution for 90 minutes imparted a significant improvement on the thermal stability of Gmelina arborea sawdust.
- 31 December 2020
- Published by Univ. of Malaya in International STEM Journal
- Vol. 1 (1) , 47-58
Open AccessTHERMAL DEGRADATION PROFILE OF CHEMICALLY MODIFIED WOOD SAWDUST
Gmelina arborea sawdust was chemically modified using 4% and 8% concentrations of NaOH solution for 30 and 90 minutes soaking times. The influence of this modification on the chemical composition and thermal properties of samples were investigated. Chemical characterization of samples revealed that the percentage content of hemicellulose decreased from 24.5% in the unmodified sample to 20.8%, 17.6% and 15.2% in samples soaked in 4% NaOH solution for 90 minutes, 8% NaOH for 30 and 90 minutes respectively. The amount of lignin decreased from 25.0% in unmodified samples to 19.0% when the sample was treated with 8% NaOH for 90 minutes. A moisture content of 9.0% and 2.5% were recorded in unmodified and sample treated with 8% NaOH for 90 minutes respectively. However, the cellulose content increased from 38.1% in unmodified sample to 60.1% when the sample was treated with 8% NaOH for 90 minutes. The percentage weight loss increased as concentration and modification time increased. Functional groups analysis by Fourier Transform Infrared Spectroscopy (FTIR) showed evidence of reduction in OH and removal of C=O groups associated with the wood polymers after chemical modification. Thermogravimetric analysis revealed that samples treated with 4% NaOH for 90 minutes presented the highest onset and peak degradation temperatures of 274.0°C and 372.1°C respectively. From these results, it can be concluded that modification with 4% NaOH solution for 90 minutes imparted a significant improvement on the thermal stability of Gmelina arborea sawdust.
- 26 September 2020
- Published by Springer Nature in Polymer Bulletin
- Vol. 78 (9) , 5181-5203
Effects of wood flour content and heat treatment on the dynamic mechanical and impact properties of LDPE/red balau (Shorea Dipterocarpaceae) composites
- 26 September 2020
- Published by Springer Nature in Polymer Bulletin
- Vol. 78 (9) , 5181-5203
Effects of wood flour content and heat treatment on the dynamic mechanical and impact properties of LDPE/red balau (Shorea Dipterocarpaceae) composites
- 1 March 2019
- Published by Springer Nature in Polymer Bulletin
- Vol. 76 (12) , 6467-6486
Influence of wood surface chemistry on the tensile and flexural properties of heat-treated mangrove/high-density polyethylene composites
- 1 March 2019
- Published by Springer Nature in Polymer Bulletin
- Vol. 76 (12) , 6467-6486
Influence of wood surface chemistry on the tensile and flexural properties of heat-treated mangrove/high-density polyethylene composites
- 13 September 2018
- Published by SAGE Publications in Journal of Thermoplastic Composite Materials
- Vol. 32 (10) , 1408-1426
Water absorption behavior of heat-treated and untreated red balau saw dust/LDPE composites: Its kinetics and effects on mechanical properties
The hygroscopic nature of wood limits the use of wood thermoplastic composites (WTC) in outdoor industrial and domestic applications. To reduce this tendency, red balau saw dust was heat treated at 180 and 200°C for 1 h and compounded with Low Density Poly(ethylene) (LDPE) into 20 and 37 wt% and then molded into test specimens by injection molding. Samples were immersed in distilled water at room temperature for 4 months. Heat-treated wood composites showed remarkable water resistance relative to untreated ones. Wood composites made from wood treated at 180 and 200°C exhibited almost similar water absorption pattern. Reduced water absorption of heat-treated wood composites relative to untreated ones indicates that heat treatment has resulted in a degree of modification of the wood. Most of the composites displayed the Fickian mode of water absorption with n values close to 0.5. Also, the diffusion coefficient reduced with wood content in untreated wood composites due to interaction of water with the polar groups in wood through hydrogen bonding. Untreated wood composites exhibited poorer mechanical properties with water immersion as a result of degradation due to moisture. The mechanical properties of the heat-treated wood composites were not adversely affected with water absorption. Therefore, heat treatment can reduce the proneness to water absorption in WTCs and alleviate the detrimental effects on mechanical properties.
- 13 September 2018
- Published by SAGE Publications in Journal of Thermoplastic Composite Materials
- Vol. 32 (10) , 1408-1426
Water absorption behavior of heat-treated and untreated red balau saw dust/LDPE composites: Its kinetics and effects on mechanical properties
The hygroscopic nature of wood limits the use of wood thermoplastic composites (WTC) in outdoor industrial and domestic applications. To reduce this tendency, red balau saw dust was heat treated at 180 and 200°C for 1 h and compounded with Low Density Poly(ethylene) (LDPE) into 20 and 37 wt% and then molded into test specimens by injection molding. Samples were immersed in distilled water at room temperature for 4 months. Heat-treated wood composites showed remarkable water resistance relative to untreated ones. Wood composites made from wood treated at 180 and 200°C exhibited almost similar water absorption pattern. Reduced water absorption of heat-treated wood composites relative to untreated ones indicates that heat treatment has resulted in a degree of modification of the wood. Most of the composites displayed the Fickian mode of water absorption with n values close to 0.5. Also, the diffusion coefficient reduced with wood content in untreated wood composites due to interaction of water with the polar groups in wood through hydrogen bonding. Untreated wood composites exhibited poorer mechanical properties with water immersion as a result of degradation due to moisture. The mechanical properties of the heat-treated wood composites were not adversely affected with water absorption. Therefore, heat treatment can reduce the proneness to water absorption in WTCs and alleviate the detrimental effects on mechanical properties.
- 31 May 2018
- Published by SAGE Publications in High Performance Polymers
- Vol. 30 (8) , 900-910
Physico-thermal properties of kenaf fiber/high-density polyethylene/maleic anhydride compatibilized composites
Kenaf fiber/high-density polyethylene/maleic anhydride (MA)-compatibilized composites were melt mixed in a twin-screw extruder and molded using injection molding machine. Physicothermal properties of the composites were studied at different percentages of compatibilizer contents using various techniques. The addition of 8% compatibilizer into 8.5 and 17.5 wt% fiber content improved the adhesion and tensile strength by 14.5% and 13.6%, respectively. Compatibilized samples exhibited higher peak load and fracture energy on impact testing compared to the samples without maleic anhydride compatibilizer. The effect of the addition of maleic anhydride compatibilizer on peak load and fracture energy was observed to be at its highest at 8%. Differential scanning calorimetric measurements revealed that the melting enthalpy and degree of crystallinity of composites increased with increasing compatibilizer content up to 8% and then decreased at 12% compatibilizer content. Dynamic mechanical analysis showed that the storage modulus of composites was increased, but the loss modulus and tangent delta were decreased after the addition of compatibilizer. This indicates that compatibilized composites produced have improved toughness and reduced stiffness.
- 31 May 2018
- Published by SAGE Publications in High Performance Polymers
- Vol. 30 (8) , 900-910
Physico-thermal properties of kenaf fiber/high-density polyethylene/maleic anhydride compatibilized composites
Kenaf fiber/high-density polyethylene/maleic anhydride (MA)-compatibilized composites were melt mixed in a twin-screw extruder and molded using injection molding machine. Physicothermal properties of the composites were studied at different percentages of compatibilizer contents using various techniques. The addition of 8% compatibilizer into 8.5 and 17.5 wt% fiber content improved the adhesion and tensile strength by 14.5% and 13.6%, respectively. Compatibilized samples exhibited higher peak load and fracture energy on impact testing compared to the samples without maleic anhydride compatibilizer. The effect of the addition of maleic anhydride compatibilizer on peak load and fracture energy was observed to be at its highest at 8%. Differential scanning calorimetric measurements revealed that the melting enthalpy and degree of crystallinity of composites increased with increasing compatibilizer content up to 8% and then decreased at 12% compatibilizer content. Dynamic mechanical analysis showed that the storage modulus of composites was increased, but the loss modulus and tangent delta were decreased after the addition of compatibilizer. This indicates that compatibilized composites produced have improved toughness and reduced stiffness.
- 5 April 2015
- Published by Wiley in Polymer Composites
- Vol. 37 (9) , 2657-2672
Mechanism of fiber/matrix bond and properties of wood polymer composites produced from alkaline‐treated Daniella oliveri wood flour
The effects of sodium hydroxide (NaOH) concentration and time of treatment on the mechanism of fiber/matrix bond and functional properties of Daniella oliveri reinforced wood polymer composites (WPCs) were investigated. The WPCs were evaluated using Fourier transform infrared spectroscopy, mechanical testing, scanning electron microscopy, thermogravimetric analysis (TGA), and differential scanning calorimetry. The fiber/matrix adhesion mechanism could be attributed to the disruption of hydrogen bonding in the D. oliveri wood fiber network structure and the removal of lignin, wax and oils covering the external surface of the fiber cell wall. This leads to an increase in desirable functional properties as alkaline concentrations reached 4 wt%, but subsequently reduced at higher concentrations, while they increased with treatment time. Analysis of the fractographs of the WPCs suggests optimization of interfacial fiber–matrix adhesion and functional properties when D. oliveri wood fiber was treated with a 4 wt% solution of NaOH for 150 min. POLYM. COMPOS., 37:2657–2672, 2016. © 2015 Society of Plastics Engineers
- 5 April 2015
- Published by Wiley in Polymer Composites
- Vol. 37 (9) , 2657-2672
Mechanism of fiber/matrix bond and properties of wood polymer composites produced from alkaline‐treated Daniella oliveri wood flour
The effects of sodium hydroxide (NaOH) concentration and time of treatment on the mechanism of fiber/matrix bond and functional properties of Daniella oliveri reinforced wood polymer composites (WPCs) were investigated. The WPCs were evaluated using Fourier transform infrared spectroscopy, mechanical testing, scanning electron microscopy, thermogravimetric analysis (TGA), and differential scanning calorimetry. The fiber/matrix adhesion mechanism could be attributed to the disruption of hydrogen bonding in the D. oliveri wood fiber network structure and the removal of lignin, wax and oils covering the external surface of the fiber cell wall. This leads to an increase in desirable functional properties as alkaline concentrations reached 4 wt%, but subsequently reduced at higher concentrations, while they increased with treatment time. Analysis of the fractographs of the WPCs suggests optimization of interfacial fiber–matrix adhesion and functional properties when D. oliveri wood fiber was treated with a 4 wt% solution of NaOH for 150 min. POLYM. COMPOS., 37:2657–2672, 2016. © 2015 Society of Plastics Engineers