Xiaomei Feng
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Xiaomei Feng has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
Yifu Shen
4 shared publicationsCongyang Lu
College of Materials Science and Technology, Nanjing University of Aeronautics and Astronautics, Nanjing, People’s Republic of China
3 shared publicationsYe Tian
College of Materials Science and Technology, Nanjing University of Aeronautics and Astronautics, Nanjing, People’s Republic of China
3 shared publications- Yifu Shen
College of Materials Science and Technology, Nanjing University of Aeronautics and Astronautics, Nanjing, China
2 shared publications - Chan Guo
College of Materials Science and Technology, Nanjing University of Aeronautics and Astronautics (NUAA), Nanjing 210016, China
1 shared publication Ding Wang
College of Materials Science and Technology, Nanjing University of Aeronautics and Astronautics, Nanjing, People’s Republic of China
1 shared publication
Latest Publications
- Open Access
The Effect of Laser Remelting during SLM on Microstructure and Mechanical Properties of CoCrFeNiNb0.25
A sub-eutectic high-entropy alloy composed of CoCrFeNiNb0.25 was prepared using a combination of mechanical powder mixing and selective laser melting (SLM). The mechanical properties of the alloy were enhanced by employing an interlayer laser remelting process. This study demonstrates the feasibility of using mechanical mixing and SLM to form an CoCrFeNiNb0.25 alloy. The interlayer laser remelting process can effectively promote the melting of Nb particles introduced by mechanical mixing, release the stresses near the unfused Nb particles, and reduce their degradation of the specimen properties. The results indicate that the CoCrFeNiNb0.25 alloy, prepared using the interlayer laser remelting process, had an average microhardness of 376 HV, a tensile strength of 974 MPa, and an elongation at break of 10.51%. This process offers a viable approach for rapidly adjusting the composition of high-entropy alloys for SLM forming.
Open AccessThe Effect of Laser Remelting during SLM on Microstructure and Mechanical Properties of CoCrFeNiNb0.25
A sub-eutectic high-entropy alloy composed of CoCrFeNiNb0.25 was prepared using a combination of mechanical powder mixing and selective laser melting (SLM). The mechanical properties of the alloy were enhanced by employing an interlayer laser remelting process. This study demonstrates the feasibility of using mechanical mixing and SLM to form an CoCrFeNiNb0.25 alloy. The interlayer laser remelting process can effectively promote the melting of Nb particles introduced by mechanical mixing, release the stresses near the unfused Nb particles, and reduce their degradation of the specimen properties. The results indicate that the CoCrFeNiNb0.25 alloy, prepared using the interlayer laser remelting process, had an average microhardness of 376 HV, a tensile strength of 974 MPa, and an elongation at break of 10.51%. This process offers a viable approach for rapidly adjusting the composition of high-entropy alloys for SLM forming.
- 1 January 2021
- Published by Elsevier in Surface and Coatings Technology
- Vol. 405
Thermal conductivity of graphene nanoplates reinforced CuCr composite coatings by mechanical alloying method
- 1 January 2021
- Published by Elsevier in Surface and Coatings Technology
- Vol. 405
Thermal conductivity of graphene nanoplates reinforced CuCr composite coatings by mechanical alloying method
- 24 April 2020
- Published by SAGE Publications in Surface Engineering
- Vol. 37 (1) , 120-128
High temperature oxidation behaviour of mono-layer and bi-layer coatings
In the current work, the mono-layer Al–Cr–Ni coating and the bi-layer Al–Ni/Al–Cr coating were successfully synthesised on the Ti–6Al–4V alloy substrate by mechanical alloying. The effect of powder ratio was studied. The microstructure and phase composition of the two coatings were investigated. The mono-layer coating was composed of grey black composite structure. In the bi-layer coating, the Al–Cr outer layer exhibited a composite structure similar to the Al–Cr–Ni coating. The results showed the approximate thickness of Al–Cr–Ni coating was 140 μm, while that of bi-layer coating was more than 200 μm. Both coatings were well bonded to the substrate. After 850°C of cyclic oxidation for 100 h, cracks only occurred at the interface of the mono-layer coating, and no significant defects were found at the two interfaces of the bi-layer coating. The cyclic oxidation test results showed the bi-layer coatings exhibited more excellent oxidation resistance.
- 24 April 2020
- Published by SAGE Publications in Surface Engineering
- Vol. 37 (1) , 120-128
High temperature oxidation behaviour of mono-layer and bi-layer coatings
In the current work, the mono-layer Al–Cr–Ni coating and the bi-layer Al–Ni/Al–Cr coating were successfully synthesised on the Ti–6Al–4V alloy substrate by mechanical alloying. The effect of powder ratio was studied. The microstructure and phase composition of the two coatings were investigated. The mono-layer coating was composed of grey black composite structure. In the bi-layer coating, the Al–Cr outer layer exhibited a composite structure similar to the Al–Cr–Ni coating. The results showed the approximate thickness of Al–Cr–Ni coating was 140 μm, while that of bi-layer coating was more than 200 μm. Both coatings were well bonded to the substrate. After 850°C of cyclic oxidation for 100 h, cracks only occurred at the interface of the mono-layer coating, and no significant defects were found at the two interfaces of the bi-layer coating. The cyclic oxidation test results showed the bi-layer coatings exhibited more excellent oxidation resistance.
- 1 June 2019
- Published by Elsevier in Surface and Coatings Technology
- Vol. 367, 212-224
Oxidation behavior of Cr-AlSi12 composite coatings on Ti-6Al-4V alloy substrate fabricated via high-energy mechanical alloying method
- 1 June 2019
- Published by Elsevier in Surface and Coatings Technology
- Vol. 367, 212-224
Oxidation behavior of Cr-AlSi12 composite coatings on Ti-6Al-4V alloy substrate fabricated via high-energy mechanical alloying method
- 1 March 2019
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 779, 456-465
Microstructures and oxidation behavior of Al-CrMnFeCoMoW composite coatings on Ti-6Al-4V alloy substrate via high-energy mechanical alloying method
- 1 March 2019
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 779, 456-465
Microstructures and oxidation behavior of Al-CrMnFeCoMoW composite coatings on Ti-6Al-4V alloy substrate via high-energy mechanical alloying method
- 4 August 2017
- Published by Springer Nature in Journal of Superconductivity and Novel Magnetism
- Vol. 31 (3) , 865-871
Structural and Magnetic Properties of the Series of Double-Perovskite Sr2−x Bi x MnMoO6
- 4 August 2017
- Published by Springer Nature in Journal of Superconductivity and Novel Magnetism
- Vol. 31 (3) , 865-871
Structural and Magnetic Properties of the Series of Double-Perovskite Sr2−x Bi x MnMoO6