Shuvo Islam
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Shuvo Islam has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
Mustaque Hossain
Department of Civil Engineering, Kansas State University, Manhattan, KS
3 shared publicationsRichard Miller
Kansas Department of Transportation, Topeka, KS, USA
2 shared publicationsAbu Sufian
Department of Civil Engineering, Kansas State University, Manhattan, KS, USA
1 shared publicationAvishek Bose
Department of Computer Science, Kansas State University, Manhattan, KS
1 shared publicationChristopher A. Jones
Department of Civil Engineering, Kansas State University, Manhattan, KS
1 shared publicationChristopher Leibrock
Kansas Department of Transportation, Topeka, KS, USA
1 shared publication
Latest Publications
- 19 March 2019
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
- Vol. 2673 (4) , 490-499
Implementation of AASHTOWare Pavement ME Design Software for Asphalt Pavements in Kansas
Many highway agencies are transitioning from the 1993 AASHTO pavement design guide to the AASHTOWare Pavement ME Design (PMED). Pavement performance models embedded in the PMED software need to be calibrated for new and reconstructed hot-mix asphalt (HMA) pavements. Twenty-seven newly constructed HMA pavements were used to calibrate the prediction models—twenty-one for calibration and six for validation. Local calibration for permanent deformation, top-down fatigue cracking, and the International Roughness Index (IRI) models was done using the traditional split-sample method. Comparison with the results from the 1993 AASHTO design guide for ten new HMA pavement sections with varying traffic levels was done. The results show that the thicknesses obtained from locally calibrated PMED are within 1 inch of the AASHTO 1993 design guide prediction for low to medium-low traffic. For sections with high traffic level, the 1993 AASHTO design guide yielded higher thickness than PMED. The PMED implementation strategies adopted in Kansas and relevant concerns are discussed. Finally, an automated calibration technique has been proposed to help highway agencies to perform periodic in-house calibration of the performance models.
- 19 March 2019
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
- Vol. 2673 (4) , 490-499
Implementation of AASHTOWare Pavement ME Design Software for Asphalt Pavements in Kansas
Many highway agencies are transitioning from the 1993 AASHTO pavement design guide to the AASHTOWare Pavement ME Design (PMED). Pavement performance models embedded in the PMED software need to be calibrated for new and reconstructed hot-mix asphalt (HMA) pavements. Twenty-seven newly constructed HMA pavements were used to calibrate the prediction models—twenty-one for calibration and six for validation. Local calibration for permanent deformation, top-down fatigue cracking, and the International Roughness Index (IRI) models was done using the traditional split-sample method. Comparison with the results from the 1993 AASHTO design guide for ten new HMA pavement sections with varying traffic levels was done. The results show that the thicknesses obtained from locally calibrated PMED are within 1 inch of the AASHTO 1993 design guide prediction for low to medium-low traffic. For sections with high traffic level, the 1993 AASHTO design guide yielded higher thickness than PMED. The PMED implementation strategies adopted in Kansas and relevant concerns are discussed. Finally, an automated calibration technique has been proposed to help highway agencies to perform periodic in-house calibration of the performance models.
- 19 November 2018
- Published by Taylor & Francis in Road Materials and Pavement Design
- Vol. 21 (5) , 1224-1237
Mechanistic-Empirical design of perpetual pavement
Perpetual pavements use multiple, durable asphalt layers to produce a safe, smooth, long-lasting road. The pavement design begins with a strong, yet flexible bottom layer that resists tensile strain caused by traffic, and thus stops cracks from forming at the bottom of the pavement. Four perpetual pavement sections were designed and constructed in 2005 and currently are scheduled for rehabilitation for top-down surface cracking. These cracks have been confirmed by full-depth cores. This study revisited the design of these perpetual pavement sections using now available PerRoad and AASHTOWare Pavement ME Design software to investigate whether the design assumptions were correct. Fatigue lives of these sections were also evaluated based on bottom-up cracking. Layer moduli were backcalculated from the falling weight deflectometer (FWD) deflection data using the EVERCALC software. Tensile strains at the bottom of the asphalt layer were then computed. Results showed that predicted strain values derived from the mechanistic response models were lower than the tensile strains computed using moduli from the FWD deflection data. The required asphalt thickness from PerRoad was relatively higher than the asphalt thickness obtained from the AASHTOWare Pavement ME Design software over a 50-year design period. The study identified the most successful perpetual pavement design as the one with a rich bituminous mix in the base layer.
- 19 November 2018
- Published by Taylor & Francis in Road Materials and Pavement Design
- Vol. 21 (5) , 1224-1237
Mechanistic-Empirical design of perpetual pavement
Perpetual pavements use multiple, durable asphalt layers to produce a safe, smooth, long-lasting road. The pavement design begins with a strong, yet flexible bottom layer that resists tensile strain caused by traffic, and thus stops cracks from forming at the bottom of the pavement. Four perpetual pavement sections were designed and constructed in 2005 and currently are scheduled for rehabilitation for top-down surface cracking. These cracks have been confirmed by full-depth cores. This study revisited the design of these perpetual pavement sections using now available PerRoad and AASHTOWare Pavement ME Design software to investigate whether the design assumptions were correct. Fatigue lives of these sections were also evaluated based on bottom-up cracking. Layer moduli were backcalculated from the falling weight deflectometer (FWD) deflection data using the EVERCALC software. Tensile strains at the bottom of the asphalt layer were then computed. Results showed that predicted strain values derived from the mechanistic response models were lower than the tensile strains computed using moduli from the FWD deflection data. The required asphalt thickness from PerRoad was relatively higher than the asphalt thickness obtained from the AASHTOWare Pavement ME Design software over a 50-year design period. The study identified the most successful perpetual pavement design as the one with a rich bituminous mix in the base layer.
- 8 October 2018
- Published by Taylor & Francis in Nondestructive Testing and Evaluation
- Vol. 34 (1) , 87-98
Evaluation of pavement surface texture at the network level
In this study, variations in surface +-texture depth within a given roadway project and across different projects were studied. Network-level surface texture data were collected on the highway network in using a 3D laser system (LCMS). Differences in mean texture depth (MTD) were estimated for five surface types (Portland concrete cement, PCC; Superpave mixes, SM-9.5A & SR-12.5A; Chip seal; Ultra-thin bonded asphalt surface, UBAS) considering the random effects of project location, surface age and annual average daily traffic. Variations in surface texture were also investigated at the horizontal curves. In addition, the relationship between the texture depth and the skid number obtained by the ASTM skid trailer were investigated. Results show that there are significant differences in average texture depth within a project and across projects. Highest MTDs were obtained for UBAS and lowest for PCC. At the network level, skid number did not correlate well with the MTDs, irrespective of surface type. However, project-level correlation is quite acceptable.
- 8 October 2018
- Published by Taylor & Francis in Nondestructive Testing and Evaluation
- Vol. 34 (1) , 87-98
Evaluation of pavement surface texture at the network level
In this study, variations in surface +-texture depth within a given roadway project and across different projects were studied. Network-level surface texture data were collected on the highway network in using a 3D laser system (LCMS). Differences in mean texture depth (MTD) were estimated for five surface types (Portland concrete cement, PCC; Superpave mixes, SM-9.5A & SR-12.5A; Chip seal; Ultra-thin bonded asphalt surface, UBAS) considering the random effects of project location, surface age and annual average daily traffic. Variations in surface texture were also investigated at the horizontal curves. In addition, the relationship between the texture depth and the skid number obtained by the ASTM skid trailer were investigated. Results show that there are significant differences in average texture depth within a project and across projects. Highest MTDs were obtained for UBAS and lowest for PCC. At the network level, skid number did not correlate well with the MTDs, irrespective of surface type. However, project-level correlation is quite acceptable.