Sonia D’ostuni
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Sonia D’ostuni has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Giuseppe Casalino
Department of Mechanics, Mathematics and Management, Polytechnic University of Bari, Bari, Italy
3 shared publications - Paola Leo
Department of Engineering for Innovation, University of Salento, Via per Monteroni, 73100 Lecce, Italy
3 shared publications - Andrea Tarantino
Innovation Engineering Department, University of Salento, Via per Arnesano s.n., 73100 Lecce, Italy
1 shared publication - Antonio Piccininni
Politecnico di Bari
1 shared publication - Claudio Mele
Dipartimento di Ingegneria dell’Innovazione, Università del Salento, via Monteroni, 73100 Lecce, Italy
1 shared publication - Gianfranco Palumbo
Politecnico di Bari
1 shared publication
Latest Publications
- Open Access
Analysis of the Process Parameters, Post-Weld Heat Treatment and Peening Effects on Microstructure and Mechanical Performance of Ti–Al Dissimilar Laser Weldings
Dissimilar Ti–Al laser weldings are very interesting due to their difficulties in being processed because of the different physical properties of the alloys and the crack formations during cooling and solidification. In this study, the effect of laser offset and defocusing on microstructure, geometry and mechanical properties response of 2 mm thick dissimilar AA6061/Ti-6Al-4V laser welds was analyzed. Moreover, in order to reduce residual stresses, the joints were both heat-treated and mechanically treated by ultrasonic peening. The welds microstructure was found to be martensitic in the Ti-6Al-4V fusion zone, columnar dendritic in the AA6061 fusion zone and partially martensitic in the Ti-6Al-4V heat-affected zone. Intermetallic compounds based on the Al–Ti system were detected at the AA6061/Ti-6Al-4V interface and in the aluminum fusion zone. Both negative defocusing and higher laser offset improved the tensile performance of the welds, mainly by reducing the amount of brittle intermetallic compounds. The stress relaxation heat treatment, leading to the aging of the martensite and the increasing of the size of the intermetallic compound, reduced the tensile strength and ductility of the joints. On the contrary, for dissimilar Al–Ti welds, mechanical treatment was effective in increasing joints ductility and, moreover, corrosion resistance.
Open AccessAnalysis of the Process Parameters, Post-Weld Heat Treatment and Peening Effects on Microstructure and Mechanical Performance of Ti–Al Dissimilar Laser Weldings
Dissimilar Ti–Al laser weldings are very interesting due to their difficulties in being processed because of the different physical properties of the alloys and the crack formations during cooling and solidification. In this study, the effect of laser offset and defocusing on microstructure, geometry and mechanical properties response of 2 mm thick dissimilar AA6061/Ti-6Al-4V laser welds was analyzed. Moreover, in order to reduce residual stresses, the joints were both heat-treated and mechanically treated by ultrasonic peening. The welds microstructure was found to be martensitic in the Ti-6Al-4V fusion zone, columnar dendritic in the AA6061 fusion zone and partially martensitic in the Ti-6Al-4V heat-affected zone. Intermetallic compounds based on the Al–Ti system were detected at the AA6061/Ti-6Al-4V interface and in the aluminum fusion zone. Both negative defocusing and higher laser offset improved the tensile performance of the welds, mainly by reducing the amount of brittle intermetallic compounds. The stress relaxation heat treatment, leading to the aging of the martensite and the increasing of the size of the intermetallic compound, reduced the tensile strength and ductility of the joints. On the contrary, for dissimilar Al–Ti welds, mechanical treatment was effective in increasing joints ductility and, moreover, corrosion resistance.
- Open Access
Off-Set and Focus Effects on Grade 5 Titanium to 6061 Aluminum Alloy Fiber Laser Weld
Joining dissimilar metal alloys together has become a major issue in the welding industry since the rapid development of innovative and performing multi-materials products. In case, titanium and Aluminum alloys can be laser-welded using a placement of the laser beam aside the weld centerline, which is called off-set. The fused zone is deep and narrow and the reaction between titanium and Aluminum is limited to a thin interlayer, which improves mechanical properties. In this paper, the effect of focus and off-set distance of the laser beam on the weldability of grade 5 titanium to 6061 Aluminum alloy dissimilar butt weld are presented. The interlayer thickness was correlated to the process parameters and tensile behavior of the weld. The map of deformation showed different deformations of the two weld sides. The data coming from the metallurgical and mechanical characterization of the weld were analyzed to figure out the best off-set and focus combination in the range studied.
Open AccessOff-Set and Focus Effects on Grade 5 Titanium to 6061 Aluminum Alloy Fiber Laser Weld
Joining dissimilar metal alloys together has become a major issue in the welding industry since the rapid development of innovative and performing multi-materials products. In case, titanium and Aluminum alloys can be laser-welded using a placement of the laser beam aside the weld centerline, which is called off-set. The fused zone is deep and narrow and the reaction between titanium and Aluminum is limited to a thin interlayer, which improves mechanical properties. In this paper, the effect of focus and off-set distance of the laser beam on the weldability of grade 5 titanium to 6061 Aluminum alloy dissimilar butt weld are presented. The interlayer thickness was correlated to the process parameters and tensile behavior of the weld. The map of deformation showed different deformations of the two weld sides. The data coming from the metallurgical and mechanical characterization of the weld were analyzed to figure out the best off-set and focus combination in the range studied.
- Open Access
FEM Simulation of Dissimilar Aluminum Titanium Fiber Laser Welding Using 2D and 3D Gaussian Heat Sources
For a dissimilar laser weld, the model of the heat source is a paramount boundary condition for the prediction of the thermal phenomena, which occur during the welding cycle. In this paper, both two-dimensional (2D) and three-dimensional (3D) Gaussian heat sources were studied for the thermal analysis of the fiber laser welding of titanium and aluminum dissimilar butt joint. The models were calibrated comparing the fusion zone of the experiment with that of the numerical model. The actual temperature during the welding cycle was registered by a thermocouple and used for validation of the numerical model. When it came to calculate the fusion zone dimensions in the transversal section, the 2D heat source showed more accurate results. The 3D heat source provided better results for the simulated weld pool and cooling rate.
Open AccessFEM Simulation of Dissimilar Aluminum Titanium Fiber Laser Welding Using 2D and 3D Gaussian Heat Sources
For a dissimilar laser weld, the model of the heat source is a paramount boundary condition for the prediction of the thermal phenomena, which occur during the welding cycle. In this paper, both two-dimensional (2D) and three-dimensional (3D) Gaussian heat sources were studied for the thermal analysis of the fiber laser welding of titanium and aluminum dissimilar butt joint. The models were calibrated comparing the fusion zone of the experiment with that of the numerical model. The actual temperature during the welding cycle was registered by a thermocouple and used for validation of the numerical model. When it came to calculate the fusion zone dimensions in the transversal section, the 2D heat source showed more accurate results. The 3D heat source provided better results for the simulated weld pool and cooling rate.