Punita Kumari
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Punita Kumari has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
Saahil
Wuhan University of Technology
4 shared publicationsAshraf Alam
Rekhi Centre of Excellence for the Science of Happiness, Indian Institute of Technology
2 shared publications- Ashraf Alam
Department of Education, National Institute of Technology Calicut, Kozhikode, India
2 shared publications - Jihui Wang
School of Materials Science and Engineering, Wuhan University of Technology, Wuhan 430070, China
2 shared publications A. V. R. Akshaya
Department of MBA, Dr. N.G.P. Institute of Technology
1 shared publicationC. Ram Kumar
Department of BME, Dr. N.G.P. Institute of Technology
1 shared publication
Latest Publications
- 8 June 2023
- Published by Springer Nature
- p. 19-33
Healthcare Administration and Management in Current Scenario
- 8 June 2023
- Published by Springer Nature
- p. 19-33
Healthcare Administration and Management in Current Scenario
- 22 April 2022
- Published by Springer Nature
- p. 131-141
FEA Investigation of Repaired Composite Under Low Velocity Impact
- 22 April 2022
- Published by Springer Nature
- p. 131-141
FEA Investigation of Repaired Composite Under Low Velocity Impact
- 17 April 2021
- Published by Springer Nature
- p. 505-514
Analysis of the Composite Sample Under Low Velocity Multi-impact Test: FEA Investigation
- 17 April 2021
- Published by Springer Nature
- p. 505-514
Analysis of the Composite Sample Under Low Velocity Multi-impact Test: FEA Investigation
- 1 January 2021
- Published by Elsevier in Materials Today: Proceedings
- Vol. 46, 645-650
Multi-impact on scarf repaired composite laminates: FE investigation
- 1 January 2021
- Published by Elsevier in Materials Today: Proceedings
- Vol. 46, 645-650
Multi-impact on scarf repaired composite laminates: FE investigation
- 1 January 2021
- Published by Elsevier in Materials Today: Proceedings
- Vol. 38, 3005-3013
Influence of the impact position on scarf repair composite under low velocity impact: FEA investigation
- 1 January 2021
- Published by Elsevier in Materials Today: Proceedings
- Vol. 38, 3005-3013
Influence of the impact position on scarf repair composite under low velocity impact: FEA investigation
- 29 April 2019
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 44 (9) , 7677-7697
Tensile After Impact Test of Scarf-Repaired Composite Laminates
- 29 April 2019
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 44 (9) , 7677-7697
Tensile After Impact Test of Scarf-Repaired Composite Laminates
- Open Access
Residual Tensile Strength of the Multi-Impacted Scarf-Repaired Glass Fiber-Reinforced Polymer (GFRP) Composites
The effect of multiple/repeated impacts on a repaired composite was investigated using a low-velocity impact test. The composite samples were fabricated through a vacuum resin infusion method (VARI) and repaired by a scarf repair technique. Later, a repeated low-velocity impact test was performed on the original and repaired composites samples. Performance of the multi-impacted repaired and original samples was evaluated and compared by measuring maximum contact force, maximum displacement, maximum time duration, absorbed energy and damage area. Photographs of the post-impacted samples were taken to observe the multi-impact damage progression through visual inspection. The results showed that each repeated impact subjected the samples to more damage. Tensile tests revealed that the scarf repair restored 81.23% strength. It was also observed that the sample obtained the highest damage dent in the low-velocity impact test that failed early during a tensile test and carried the lowest ultimate load.
Open AccessResidual Tensile Strength of the Multi-Impacted Scarf-Repaired Glass Fiber-Reinforced Polymer (GFRP) Composites
The effect of multiple/repeated impacts on a repaired composite was investigated using a low-velocity impact test. The composite samples were fabricated through a vacuum resin infusion method (VARI) and repaired by a scarf repair technique. Later, a repeated low-velocity impact test was performed on the original and repaired composites samples. Performance of the multi-impacted repaired and original samples was evaluated and compared by measuring maximum contact force, maximum displacement, maximum time duration, absorbed energy and damage area. Photographs of the post-impacted samples were taken to observe the multi-impact damage progression through visual inspection. The results showed that each repeated impact subjected the samples to more damage. Tensile tests revealed that the scarf repair restored 81.23% strength. It was also observed that the sample obtained the highest damage dent in the low-velocity impact test that failed early during a tensile test and carried the lowest ultimate load.