Roberto Bortolussi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Roberto Bortolussi has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Fabrizio Leonardi
FEI University Center, So Bernardo do Campo, Brazil
2 shared publications - Agenor de Toledo Fleury
Escola Politécnica da USP, São Paulo, Brazil
1 shared publication - André de Souza Mendes
FEI University Center, So Bernardo do Campo, Brazil
1 shared publication - Ed Claudio Bordinassi
Maua Institute of Technology
1 shared publication - Marko Ackermann
Department of Mechanical Engineering, Centro Universitário FEI, São Bernardo do Campo, Brazil
1 shared publication Nelson Wilson Paschoalinoto
Department of Mechanical Engineering, University Center of FEI, São Bernardo do Campo, Brazil
1 shared publication
Latest Publications
- 25 June 2020
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture
- Vol. 235 (1-2) , 290-300
The effect of process parameters and cutting tool shape on residual stress of SAE 52100 hard turned steel by high speed machining
This study focused on determining the residual stress of SAE 52100 hard-turned steel. The objective was to evaluate and compare the effects of the cutting-edge geometry and cutting parameters (cutting speed, feed rate, and cutting depth) on the residual stresses of three different conventional inserts: S-WNGA08 0408S01020A 7025, T-WNGA08 0408T01020A 7025, and S-WNGA432S0330A 7025. Tests were performed on 60 samples of SAE 52100 hardened steel with an average hardness of 58.5 HRC. The circumferential residual stresses of the samples were measured by X-ray diffraction. A full factorial design of experiments with three factors and two levels each with two central points and a replicate was used for a statistical analysis. The most significant results were as follows: For all inserts, the measured residual stresses were compressive, which extended the tool lifespan. The residual stresses of the Type-S inserts were significantly influenced by the cutting speed and depth, and those of the Type-T insert were significantly influenced by the feed rate and cutting depth. In addition, the residual stresses of the insert 3 were more compressive than those of the other two types of inserts. In other words, residual stresses are more compressive for inserts with larger chamfer angles even as the principal residual stress profiles were all compressive. This work has also shown that it is possible to determine a significant statistical relationship between cutting forces and residual stresses, allowing force measurements to predict the residual stress without any information on process parameters.
- 25 June 2020
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture
- Vol. 235 (1-2) , 290-300
The effect of process parameters and cutting tool shape on residual stress of SAE 52100 hard turned steel by high speed machining
This study focused on determining the residual stress of SAE 52100 hard-turned steel. The objective was to evaluate and compare the effects of the cutting-edge geometry and cutting parameters (cutting speed, feed rate, and cutting depth) on the residual stresses of three different conventional inserts: S-WNGA08 0408S01020A 7025, T-WNGA08 0408T01020A 7025, and S-WNGA432S0330A 7025. Tests were performed on 60 samples of SAE 52100 hardened steel with an average hardness of 58.5 HRC. The circumferential residual stresses of the samples were measured by X-ray diffraction. A full factorial design of experiments with three factors and two levels each with two central points and a replicate was used for a statistical analysis. The most significant results were as follows: For all inserts, the measured residual stresses were compressive, which extended the tool lifespan. The residual stresses of the Type-S inserts were significantly influenced by the cutting speed and depth, and those of the Type-T insert were significantly influenced by the feed rate and cutting depth. In addition, the residual stresses of the insert 3 were more compressive than those of the other two types of inserts. In other words, residual stresses are more compressive for inserts with larger chamfer angles even as the principal residual stress profiles were all compressive. This work has also shown that it is possible to determine a significant statistical relationship between cutting forces and residual stresses, allowing force measurements to predict the residual stress without any information on process parameters.
- Open Access
- 16 November 2018
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering
- Vol. 233 (12) , 2987-2999
Assessing the influence of the road-tire friction coefficient on the yaw and roll stability of articulated vehicles
This article addresses the yaw stability of articulated vehicles by assessing the influence of the road-tire friction coefficient on the convergence region of a particular equilibrium condition. In addition, the boundaries of this region are compared to the boundaries of the non-jackknife and non-rollover regions to distinguish the instability phenomenon, jackknife or roll-over, responsible for this delimitation. The vehicle configuration considered in this analysis is composed by one tractor unit and one towed unit connected through an articulation point, for instance, a tractor-semitrailer combination. A nonlinear articulated bicycle model with four degrees of freedom is used together with a nonlinear lateral force tire model. To estimate the convergence region, the phase trajectory method is used. The equations of motion of the mathematical model are numerically integrated for different initial conditions in the phase plane, and the state orbits are monitored in order to verify the convergence point and the occurrence of instability events. In all cases, the longitudinal force on each tire, such as traction and braking, is not considered. The results show the existence of convergence regions delimited only by jackknife events, for low values of the friction coefficient, and only by rollover events, for high values of the friction coefficient. Moreover, the transition between these two conditions as the friction coefficient is changed is graphically presented. The main contributions of this article are the identification of the abrupt reduction of the convergence region as the value of the friction coefficient increases and the distinction of the instability events, jackknife or rollover, that define the boundaries of the convergence region.
- 16 November 2018
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering
- Vol. 233 (12) , 2987-2999
Open AccessAssessing the influence of the road-tire friction coefficient on the yaw and roll stability of articulated vehicles
This article addresses the yaw stability of articulated vehicles by assessing the influence of the road-tire friction coefficient on the convergence region of a particular equilibrium condition. In addition, the boundaries of this region are compared to the boundaries of the non-jackknife and non-rollover regions to distinguish the instability phenomenon, jackknife or roll-over, responsible for this delimitation. The vehicle configuration considered in this analysis is composed by one tractor unit and one towed unit connected through an articulation point, for instance, a tractor-semitrailer combination. A nonlinear articulated bicycle model with four degrees of freedom is used together with a nonlinear lateral force tire model. To estimate the convergence region, the phase trajectory method is used. The equations of motion of the mathematical model are numerically integrated for different initial conditions in the phase plane, and the state orbits are monitored in order to verify the convergence point and the occurrence of instability events. In all cases, the longitudinal force on each tire, such as traction and braking, is not considered. The results show the existence of convergence regions delimited only by jackknife events, for low values of the friction coefficient, and only by rollover events, for high values of the friction coefficient. Moreover, the transition between these two conditions as the friction coefficient is changed is graphically presented. The main contributions of this article are the identification of the abrupt reduction of the convergence region as the value of the friction coefficient increases and the distinction of the instability events, jackknife or rollover, that define the boundaries of the convergence region.