Goran Vasilic
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Goran Vasilic has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Sasa Zivanovic
Faculty of Mechanical Engineering, University of Belgrade, Belgrade, Serbia
8 shared publications Sasa Zivanovic
University of Belgrade
4 shared publications- Branko Kokotovic
University of Belgrade
3 shared publications - Milan Milutinović
Akademija tehničkih strukovnih studija Politehnika Beograd
3 shared publications - Zoran Dimic
Lola Institute, Belgrade, Serbia
3 shared publications Branko Kokotovic
University of Belgrade
2 shared publications
Latest Publications
- 1 January 2026
- Published by Centre for Evaluation in Education and Science (CEON/CEES)
- No. 5. Section,p. 431-436
Reach and workspace envelope analysis of the six-DoF articulated robot ARma6
This paper presents the reach and position workspace envelope analysis of the six-degree-of-freedom articulated robot ARma6 based on the solution of its forward kinematic problem. The robot reach is determined by combining Monte Carlo sampling with nonlinear optimization, while the limits of Tool Centre Point (TCP) in Cartesian space are obtained analytically using trigonometric relations. The rotational symmetry of the positional workspace is exploited to simplify the three-dimensional positional workspace's envelope determination, with two approaches considered: numerical extraction of the inner and outer radial boundaries and a geometric approach based on the circular TCP path corresponding to the effective robot reach. The obtained results characterize the reach and position workspace of the ARma6 robot and provide a basis for further evaluation of its geometry during the design process.
- 1 January 2026
- Published by Centre for Evaluation in Education and Science (CEON/CEES)
- No. 5. Section,p. 431-436
Reach and workspace envelope analysis of the six-DoF articulated robot ARma6
This paper presents the reach and position workspace envelope analysis of the six-degree-of-freedom articulated robot ARma6 based on the solution of its forward kinematic problem. The robot reach is determined by combining Monte Carlo sampling with nonlinear optimization, while the limits of Tool Centre Point (TCP) in Cartesian space are obtained analytically using trigonometric relations. The rotational symmetry of the positional workspace is exploited to simplify the three-dimensional positional workspace's envelope determination, with two approaches considered: numerical extraction of the inner and outer radial boundaries and a geometric approach based on the circular TCP path corresponding to the effective robot reach. The obtained results characterize the reach and position workspace of the ARma6 robot and provide a basis for further evaluation of its geometry during the design process.
- Open Access
- 1 January 2026
- Published by Centre for Evaluation in Education and Science (CEON/CEES) in Tehnika
- Vol. 81 (1) , 43-52
Parametric programs of group technology for the production of tool parts for plastic injection molding on a CNC milling machine
Creating G-code programs for CNC machines intended for any machining process requires certain resources such as time, but also a certain level of knowledge and training of programmers and operators of CNC machines. With the aim of optimally using the existing resources of a production facility, within this work, parametric programs intended for CNC milling machines were analyzed. The analyzed parametric programs were compiled so that they represent part of the group's technology for the production of plastic injection tool parts. The parametric programs themselves are generalized and therefore universal and can be used for the implementation of a specific operation, regardless of the values of the geometric quantities that describe the shape and size of the machine part. For each of the displayed parametric programs, appropriate explanations are given through sketches, algorithms and selected parts of the program. Verification of the analyzed programs was done in the LinuxCNC software system for programming and controlling CNC machines, which confirmed their correctness.
- 1 January 2026
- Published by Centre for Evaluation in Education and Science (CEON/CEES) in Tehnika
- Vol. 81 (1) , 43-52
Open AccessParametric programs of group technology for the production of tool parts for plastic injection molding on a CNC milling machine
Creating G-code programs for CNC machines intended for any machining process requires certain resources such as time, but also a certain level of knowledge and training of programmers and operators of CNC machines. With the aim of optimally using the existing resources of a production facility, within this work, parametric programs intended for CNC milling machines were analyzed. The analyzed parametric programs were compiled so that they represent part of the group's technology for the production of plastic injection tool parts. The parametric programs themselves are generalized and therefore universal and can be used for the implementation of a specific operation, regardless of the values of the geometric quantities that describe the shape and size of the machine part. For each of the displayed parametric programs, appropriate explanations are given through sketches, algorithms and selected parts of the program. Verification of the analyzed programs was done in the LinuxCNC software system for programming and controlling CNC machines, which confirmed their correctness.
- 1 January 2025
- Published by University Library in Kragujevac
- p. 300
CNC SIMULATOR BASED ON LINUXCNC CONTROL AND PROGRAMMING SYSTEM
This work presents a CNC simulator that was created based on the need to design and form a working environment within which training of operators and programmers of CNC machines will be carried out in an economically profitable way. The CNC simulator is based on a Raspberry PI 5 microcomputer and LinuxCNC open-source software system intended for control and programming of CNC machines and industrial robots. The LinuxCNC software system was configured according to the set requirements and current needs. With the control system configured in this way, two working environments were formed that are currently used in the realization of laboratory exercises of the teaching process of the higher education institution. In the framework of the paper, the created working environments are described, and in the conclusion, the observations obtained by analyzing the results achieved using the CNC simulator are presented.
- 1 January 2025
- Published by University Library in Kragujevac
- p. 300
CNC SIMULATOR BASED ON LINUXCNC CONTROL AND PROGRAMMING SYSTEM
This work presents a CNC simulator that was created based on the need to design and form a working environment within which training of operators and programmers of CNC machines will be carried out in an economically profitable way. The CNC simulator is based on a Raspberry PI 5 microcomputer and LinuxCNC open-source software system intended for control and programming of CNC machines and industrial robots. The LinuxCNC software system was configured according to the set requirements and current needs. With the control system configured in this way, two working environments were formed that are currently used in the realization of laboratory exercises of the teaching process of the higher education institution. In the framework of the paper, the created working environments are described, and in the conclusion, the observations obtained by analyzing the results achieved using the CNC simulator are presented.
- Open Access
- 1 January 2024
- Published by Centre for Evaluation in Education and Science (CEON/CEES) in Tehnika
- Vol. 79 (6) , 699-706
Parametric programming of CNC lathes
Parametric programming of CNC machines belongs to advanced programming techniques that provide several advantages compared to the generally accepted ways of creating G-code programs. Until now, manufacturers of CNC machines and their control units have mostly used this way of programming to create fixed processing cycles. Despite the range of possibilities it provides, parametric programming is not sufficiently representative of the end users of CNC machines. CNC machine programmers do not use this way of programming due to insufficient training and a lack of literature for education. This paper presents the basics and principles of parametric programming of CNC machines. According to the explanations, a parametric program can be written for any CNC machine. The paper presents examples of parametric programs written for typical operations realized on a CNC lathe.
- 1 January 2024
- Published by Centre for Evaluation in Education and Science (CEON/CEES) in Tehnika
- Vol. 79 (6) , 699-706
Open AccessParametric programming of CNC lathes
Parametric programming of CNC machines belongs to advanced programming techniques that provide several advantages compared to the generally accepted ways of creating G-code programs. Until now, manufacturers of CNC machines and their control units have mostly used this way of programming to create fixed processing cycles. Despite the range of possibilities it provides, parametric programming is not sufficiently representative of the end users of CNC machines. CNC machine programmers do not use this way of programming due to insufficient training and a lack of literature for education. This paper presents the basics and principles of parametric programming of CNC machines. According to the explanations, a parametric program can be written for any CNC machine. The paper presents examples of parametric programs written for typical operations realized on a CNC lathe.
- Open Access
- 1 January 2022
- Published by Centre for Evaluation in Education and Science (CEON/CEES) in Scientific Technical Review
- Vol. 72 (1) , 42-47
Development of a new CNC grinding machine for 3+2-axis grinding of the profile rotary milling cutter
Due to the great expansion of woodworking, profile tools manufacturing has become current and in demand. In wood industry there are two large groups of tools: rotary and spindle milling cutters that can be profile or flat. The technology of making profile rotary milling cutters requires, apart from cutting, turning, milling, 5-axis grinding operation that is performed on a 5-axis CNC grinding machine with the A'OXYZC configuration.It is a machine of a very complex kinematics and high cost-price. The paper presents a new machine that has been built for 3+2-axis grinding - Profilator 100,used for industrial manufacturing of rotary and spindle profile milling cutters. The accuracy of measures and shapes of the profile cutters built on Profilator 100 is of a high level and in industrial exploitation the difference is not observed between the profile cutters built on 5-axis CNC grinding machines. Regarding technoeconomic cost-effectiveness, production costs of Profilator 100 are lower even by ten times compared to the cost-price of 5-axis CNC grinding machines of renowned world manufacturers such as Schneeberger and Volmer.
- 1 January 2022
- Published by Centre for Evaluation in Education and Science (CEON/CEES) in Scientific Technical Review
- Vol. 72 (1) , 42-47
Open AccessDevelopment of a new CNC grinding machine for 3+2-axis grinding of the profile rotary milling cutter
Due to the great expansion of woodworking, profile tools manufacturing has become current and in demand. In wood industry there are two large groups of tools: rotary and spindle milling cutters that can be profile or flat. The technology of making profile rotary milling cutters requires, apart from cutting, turning, milling, 5-axis grinding operation that is performed on a 5-axis CNC grinding machine with the A'OXYZC configuration.It is a machine of a very complex kinematics and high cost-price. The paper presents a new machine that has been built for 3+2-axis grinding - Profilator 100,used for industrial manufacturing of rotary and spindle profile milling cutters. The accuracy of measures and shapes of the profile cutters built on Profilator 100 is of a high level and in industrial exploitation the difference is not observed between the profile cutters built on 5-axis CNC grinding machines. Regarding technoeconomic cost-effectiveness, production costs of Profilator 100 are lower even by ten times compared to the cost-price of 5-axis CNC grinding machines of renowned world manufacturers such as Schneeberger and Volmer.
- Open Access
- 1 January 2022
- Published by Centre for Evaluation in Education and Science (CEON/CEES) in Tehnika
- Vol. 77 (3) , 321-327
Technology for manufacturing of shaper milling cutters by 3+2 grinding proces on horizontal CNC milling center
The paper presents the technology of making brazed shaper milling cutters and with special reference to 5-axis grinding process (making of profile blades) on CNC grinding machine tool. Based on the analysis of the kinematics of the 5-axis grinding process, a new concept of profile milling tool production by a 3+2 axis grinding process on horizontal milling center was established. By Applying new concept, one tooth of profile tool was machined by grinding process. By obtained results, new approach for manufacturing of profile milling tools was verified.
- 1 January 2022
- Published by Centre for Evaluation in Education and Science (CEON/CEES) in Tehnika
- Vol. 77 (3) , 321-327
Open AccessTechnology for manufacturing of shaper milling cutters by 3+2 grinding proces on horizontal CNC milling center
The paper presents the technology of making brazed shaper milling cutters and with special reference to 5-axis grinding process (making of profile blades) on CNC grinding machine tool. Based on the analysis of the kinematics of the 5-axis grinding process, a new concept of profile milling tool production by a 3+2 axis grinding process on horizontal milling center was established. By Applying new concept, one tooth of profile tool was machined by grinding process. By obtained results, new approach for manufacturing of profile milling tools was verified.
- 19 November 2021
- Published by Springer Nature
- p. 179-197
Configuring a Class of Machines Based on Reconfigurable 2DOF Planar Parallel Mechanism
- 19 November 2021
- Published by Springer Nature
- p. 179-197
Configuring a Class of Machines Based on Reconfigurable 2DOF Planar Parallel Mechanism
- 1 July 2020
- Published by Elsevier in Mechanism and Machine Theory
- Vol. 149
Configuring and analysis of complex multi-axis reconfigurable machine for wire cutting process
- 1 July 2020
- Published by Elsevier in Mechanism and Machine Theory
- Vol. 149
Configuring and analysis of complex multi-axis reconfigurable machine for wire cutting process
- 2 July 2019
- Published by Springer Nature in Journal of Mechanical Science and Technology
- Vol. 33 (7) , 3407-3421
Configuring and analysis of a class of generalized reconfigurable 2-axis parallel kinematic machine
- 2 July 2019
- Published by Springer Nature in Journal of Mechanical Science and Technology
- Vol. 33 (7) , 3407-3421
Configuring and analysis of a class of generalized reconfigurable 2-axis parallel kinematic machine
- Open Access
- 1 January 2018
- Published by Centre for Evaluation in Education and Science (CEON/CEES) in Tehnika
- Vol. 73 (5) , 519-526
Configuring of a virtual refonfigurable 2-axis paralel kinematic machine integrated with the open arhitecture CNC system based on EMC2 software
The paper presents the concepts of a reconfigurable 2 axis parallel kinematic machine that is controled using the PC Linux CNC system EMC2. In this paper given the methodology for configuring a virtual machine tool that integrates with the control system and which is also reconfigurable. Verification of the methodology was achieved by plotting the programmed contour test, on various types and subvariants of the machine, on configured virtual and real machines.
- 1 January 2018
- Published by Centre for Evaluation in Education and Science (CEON/CEES) in Tehnika
- Vol. 73 (5) , 519-526
Open AccessConfiguring of a virtual refonfigurable 2-axis paralel kinematic machine integrated with the open arhitecture CNC system based on EMC2 software
The paper presents the concepts of a reconfigurable 2 axis parallel kinematic machine that is controled using the PC Linux CNC system EMC2. In this paper given the methodology for configuring a virtual machine tool that integrates with the control system and which is also reconfigurable. Verification of the methodology was achieved by plotting the programmed contour test, on various types and subvariants of the machine, on configured virtual and real machines.