Lukas Kull
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Lukas Kull has a total of 39 co-authors. Here are the top co-authors by number of shared publications:
- Thomas Morf
Hybrid Cloud Research, IBM Research, Europe Zurich Laboratory, Rueschlikon, Switzerland
13 shared publications Christian Menolfi
IBM Research-Zurich, 8803 Rüeschlikon, Switzerland. They are now with Cisco Systems, 8304 Zürich, Switzerland
12 shared publicationsMarcel Kossel
IBM Research-Zurich, 8803 Rueschlikon, Switzerland
12 shared publications- Thomas Toifl
IBM Research Zürich, Rüschlikon, Switzerland
12 shared publications Pier Andrea Francese
IBM Research Zürich, Rüschlikon, Switzerland
11 shared publicationsAlessandro Cevrero
IBM Research-Zurich, 8803 Rüeschlikon, Switzerland. They are now with Cisco Systems, 8304 Zürich, Switzerland
9 shared publications
Latest Publications
- 23 September 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 55 (1) , 38-48
A 161-mW 56-Gb/s ADC-Based Discrete Multitone Wireline Receiver Data-Path in 14-nm FinFET
This article introduces a wireline receiver (RX) data-path employing discrete multi-tone (DMT) modulation for communicating over electrical links. The DMT RX incorporates a fully digital equalization data-path, with a synthesized and automatically placed and routed digital signal processor (DSP) following a 10-bit time-interleaved pipelined successive-approximation register analog-to-digital converter (TI-PISAR ADC). The prototype RX chip implemented in a 14-nm FinFET process demonstrates a lane data rate of 56 Gb/s dissipating 161 mW including the ADC and the DSP power. The energy efficiency of 1.2 pJ/b for the DSP and 2.9 pJ/b for the entire RX was achieved with the data-rate of 56 Gb/s for communicating over channels exhibiting up to 28-dB loss at 14 GHz with a bit-error-rate (BER) better than 2e-4.
- 23 September 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 55 (1) , 38-48
A 161-mW 56-Gb/s ADC-Based Discrete Multitone Wireline Receiver Data-Path in 14-nm FinFET
This article introduces a wireline receiver (RX) data-path employing discrete multi-tone (DMT) modulation for communicating over electrical links. The DMT RX incorporates a fully digital equalization data-path, with a synthesized and automatically placed and routed digital signal processor (DSP) following a 10-bit time-interleaved pipelined successive-approximation register analog-to-digital converter (TI-PISAR ADC). The prototype RX chip implemented in a 14-nm FinFET process demonstrates a lane data rate of 56 Gb/s dissipating 161 mW including the ADC and the DSP power. The energy efficiency of 1.2 pJ/b for the DSP and 2.9 pJ/b for the entire RX was achieved with the data-rate of 56 Gb/s for communicating over channels exhibiting up to 28-dB loss at 14 GHz with a bit-error-rate (BER) better than 2e-4.
- 29 August 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 53 (11) , 3268-3279
A 12-bit 300-MS/s SAR ADC With Inverter-Based Preamplifier and Common-Mode-Regulation DAC in 14-nm CMOS FinFET
A single-channel 12-bit SAR ADC achieving 250–340 MS/s and consuming 4.8–8.0 mW from 0.75 to 0.9 V is presented. At 300 MS/s, the ADC exhibits 61.6-dB peak SNDR and reaches 60.5-dB SNDR and 78.7-dB SFDR with 0.8- $\text{V}_{\text {pp, diff}}$ input amplitude at Nyquist. It consumes 7.0 mW from a single 0.85-V supply, where 3.7 mW is contributed by the reference buffer. The key element is a comparator with an inverter-based preamplifier to achieve low-noise performance with below 1- $\text{V}_{\text {pp, diff}}$ input amplitude. The common-mode (CM) sensitivity of the inverter is counteracted by an SAR-based CM regulation (CMREG). The regulation adjusts the sampled CM to the optimal CM for the maximum inverter gain using a second capacitive DAC. It adjusts the CM on a sample-by-sample basis and, thus, can correct time-varying CM. The implemented CMREG maintains SNDR above 60 dB for a differential input amplitude mismatch of up to 2 dB or a phase mismatch of up to 15°.
- 29 August 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 53 (11) , 3268-3279
A 12-bit 300-MS/s SAR ADC With Inverter-Based Preamplifier and Common-Mode-Regulation DAC in 14-nm CMOS FinFET
A single-channel 12-bit SAR ADC achieving 250–340 MS/s and consuming 4.8–8.0 mW from 0.75 to 0.9 V is presented. At 300 MS/s, the ADC exhibits 61.6-dB peak SNDR and reaches 60.5-dB SNDR and 78.7-dB SFDR with 0.8- $\text{V}_{\text {pp, diff}}$ input amplitude at Nyquist. It consumes 7.0 mW from a single 0.85-V supply, where 3.7 mW is contributed by the reference buffer. The key element is a comparator with an inverter-based preamplifier to achieve low-noise performance with below 1- $\text{V}_{\text {pp, diff}}$ input amplitude. The common-mode (CM) sensitivity of the inverter is counteracted by an SAR-based CM regulation (CMREG). The regulation adjusts the sampled CM to the optimal CM for the maximum inverter gain using a second capacitive DAC. It adjusts the CM on a sample-by-sample basis and, thus, can correct time-varying CM. The implemented CMREG maintains SNDR above 60 dB for a differential input amplitude mismatch of up to 2 dB or a phase mismatch of up to 15°.
- 14 August 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 53 (12) , 3508-3516
A 24–72-GS/s 8-b Time-Interleaved SAR ADC With 2.0–3.3-pJ/Conversion and >30 dB SNDR at Nyquist in 14-nm CMOS FinFET
A 24-72-GS/s 8-b time-interleaved analog-to-digital converter (ADC) is presented which exceeds 39-dB SNDR at low input frequency and 30-dB SNDR at Nyquist. High SNDR at Nyquist is achieved by 16 parallel sampling switches driven by short clock pulses. Clock-pulse edges can be shifted digitally to reduce the impact of timing mismatch. A total of 64 asynchronous 8-b successive approximation (SAR) ADCs at low supply voltage convert sampled voltages. The SAR ADCs use a differential capacitive DAC, one comparator per decision, and include a reference voltage DAC and buffer. The ADC consumes 2.0 pJ/conversion at 48 GS/s and 3.3 pJ/conversion at 72 GS/s and is implemented in 14-nm CMOS FinFET on 0.15 mm².
- 14 August 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 53 (12) , 3508-3516
A 24–72-GS/s 8-b Time-Interleaved SAR ADC With 2.0–3.3-pJ/Conversion and >30 dB SNDR at Nyquist in 14-nm CMOS FinFET
A 24-72-GS/s 8-b time-interleaved analog-to-digital converter (ADC) is presented which exceeds 39-dB SNDR at low input frequency and 30-dB SNDR at Nyquist. High SNDR at Nyquist is achieved by 16 parallel sampling switches driven by short clock pulses. Clock-pulse edges can be shifted digitally to reduce the impact of timing mismatch. A total of 64 asynchronous 8-b successive approximation (SAR) ADCs at low supply voltage convert sampled voltages. The SAR ADCs use a differential capacitive DAC, one comparator per decision, and include a reference voltage DAC and buffer. The ADC consumes 2.0 pJ/conversion at 48 GS/s and 3.3 pJ/conversion at 72 GS/s and is implemented in 14-nm CMOS FinFET on 0.15 mm².
- 1 June 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 267-268
A 50GB/S 1.6PJ/B RX Data-Path with Quarter-Rate 3-Tap Speculative DFE
A decision feedback equalization (DFE) technique suitable for high data-rate I/O link receivers is presented. The technique leverages quarter-rate data slicing to implement a fully speculative 3-tap DFE and uses clock forwarding to reach a speed of 50Gb/s. It corresponds to 20ps timing closure of the most critical path, which is the feedback of the first DFE tap. The RX data-path is implemented in 14nm FinFET CMOS SOI technology. At 0.9V supply the energy-efficiency is 1.6pJ/b when PRBS15 data transmitted at 50Gb/s across a channel with 32.5dB insertion loss are recovered with >30% horizontal margin (BER<;10- 12 ).
- 1 June 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 267-268
A 50GB/S 1.6PJ/B RX Data-Path with Quarter-Rate 3-Tap Speculative DFE
A decision feedback equalization (DFE) technique suitable for high data-rate I/O link receivers is presented. The technique leverages quarter-rate data slicing to implement a fully speculative 3-tap DFE and uses clock forwarding to reach a speed of 50Gb/s. It corresponds to 20ps timing closure of the most critical path, which is the feedback of the first DFE tap. The RX data-path is implemented in 14nm FinFET CMOS SOI technology. At 0.9V supply the energy-efficiency is 1.6pJ/b when PRBS15 data transmitted at 50Gb/s across a channel with 32.5dB insertion loss are recovered with >30% horizontal margin (BER<;10- 12 ).
- 1 January 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Parallel Implementation Technique of Digital Equalizer for Ultra-High-Speed Wireline Receiver
This paper presents a parallel implementation technique of digital equalizer for high-speed wireline serial link receiver (RX). In wireline RX, inter-symbol interference (ISI) is mitigated by continuous-time linear equalizer, and the remaining ISI is cancelled out by decision-feedback equalizer (DFE). However, due to the existence of feedback loop in DFE, there is no trivial way to parallelize it, making it difficult to be realized in digital circuits for wireline RX based on analog-to-digital converter (ADC) with ≥ 56 Gb/s data rate. In this work, convolution theorem is applied for achieving parallel digital equalizer implementation. The digital equalizer datapath consists of discrete Fourier transform (DFT) core, inverse-DFT (IDFT) core, complex multipliers between DFT and IDFT cores, and overlap-add circuit. Design considerations for low-area VLSI implementation of such architecture is discussed.
- 1 January 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Parallel Implementation Technique of Digital Equalizer for Ultra-High-Speed Wireline Receiver
This paper presents a parallel implementation technique of digital equalizer for high-speed wireline serial link receiver (RX). In wireline RX, inter-symbol interference (ISI) is mitigated by continuous-time linear equalizer, and the remaining ISI is cancelled out by decision-feedback equalizer (DFE). However, due to the existence of feedback loop in DFE, there is no trivial way to parallelize it, making it difficult to be realized in digital circuits for wireline RX based on analog-to-digital converter (ADC) with ≥ 56 Gb/s data rate. In this work, convolution theorem is applied for achieving parallel digital equalizer implementation. The digital equalizer datapath consists of discrete Fourier transform (DFT) core, inverse-DFT (IDFT) core, complex multipliers between DFT and IDFT cores, and overlap-add circuit. Design considerations for low-area VLSI implementation of such architecture is discussed.
- 1 September 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 115-118
DDR4 transmitter with AC-boost equalization and wide-band voltage regulators for thin-oxide protection in 14-nm SOI CMOS technology
A DDR4 transmitter (TX) for direct-attach memory on a processor chip is presented as well as the design of the associated low-dropout linear voltage regulators (LDO) that generate the split-mode supply voltages for the thin-oxide protection of the TX output stages operated from the 1.2 V DDR4-supply. The TX uses AC-boost equalization. Signal-integrity (SI) simulations have shown that pre-emphasis equalization is better suited to meet the DRAM eye mask specification than de-emphasis equalization. The LDO design is optimized for good frequency compensation at large load variations, which typically occur during burst-mode transmissions in DDR memory links. A wide-band low-output impedance buffer located between the LDO's error amplifier and the power transistor is proposed that implements a load-sensing and current-injection scheme to extend the low-output impedance range of the buffer, which in turn stabilizes the dominant output pole over a wider di/dt-range. The design is implemented in 14-nm silicon-on-insulator (SOI) CMOS technology, and the key performance measures are 2.8 pJ/b efficiency of the TX when driving with 34 Ω into a 40 Ω DRAM load and a figure-of-merit (FOM) of 96 ps for the LDO.
- 1 September 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 115-118
DDR4 transmitter with AC-boost equalization and wide-band voltage regulators for thin-oxide protection in 14-nm SOI CMOS technology
A DDR4 transmitter (TX) for direct-attach memory on a processor chip is presented as well as the design of the associated low-dropout linear voltage regulators (LDO) that generate the split-mode supply voltages for the thin-oxide protection of the TX output stages operated from the 1.2 V DDR4-supply. The TX uses AC-boost equalization. Signal-integrity (SI) simulations have shown that pre-emphasis equalization is better suited to meet the DRAM eye mask specification than de-emphasis equalization. The LDO design is optimized for good frequency compensation at large load variations, which typically occur during burst-mode transmissions in DDR memory links. A wide-band low-output impedance buffer located between the LDO's error amplifier and the power transistor is proposed that implements a load-sensing and current-injection scheme to extend the low-output impedance range of the buffer, which in turn stabilizes the dominant output pole over a wider di/dt-range. The design is implemented in 14-nm silicon-on-insulator (SOI) CMOS technology, and the key performance measures are 2.8 pJ/b efficiency of the TX when driving with 34 Ω into a 40 Ω DRAM load and a figure-of-merit (FOM) of 96 ps for the LDO.
- 24 November 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
CMOS ADCs Towards 100 GS/s and Beyond
The implementation of a 64x time-interleaved ADC in 32nm CMOS SOI is analyzed. Measurement results confirm 33 dB SNDR up to 19.9 GHz at 90 GS/s and 1.2V supply. Architecture details and analysis show insights into limitations and potentials of the chosen architecture. In par-ticular the input bandwidth is of concern for ADCs at more than 64 GS/s, as a larger number of sampling switches in-creases the parasitic load and reduces the input bandwidth. Insights on a simplified analysis of interleaver structures and existing solutions to bandwidth issues are highlighted and show a path to extend the sampling speed of CMOS ADCs beyond 100 GS/s.
- 24 November 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
CMOS ADCs Towards 100 GS/s and Beyond
The implementation of a 64x time-interleaved ADC in 32nm CMOS SOI is analyzed. Measurement results confirm 33 dB SNDR up to 19.9 GHz at 90 GS/s and 1.2V supply. Architecture details and analysis show insights into limitations and potentials of the chosen architecture. In par-ticular the input bandwidth is of concern for ADCs at more than 64 GS/s, as a larger number of sampling switches in-creases the parasitic load and reduces the input bandwidth. Insights on a simplified analysis of interleaver structures and existing solutions to bandwidth issues are highlighted and show a path to extend the sampling speed of CMOS ADCs beyond 100 GS/s.
- 11 February 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 32 (1) , 363-377
Modeling and Pareto Optimization of On-Chip Switched Capacitor Converters
The operation and efficiency of on-chip switched-capacitor (SC) converters are highly affected by the parasitic bottom plate capacitor present in on-chip capacitor technologies. Existing modeling frameworks do not in a comprehensive manner take the effect of the bottom plate capacitor on converter operation and efficiency into account. This paper extends an existing SC state space modeling framework to include the bottom plate capacitor. The developed model is used in a Pareto optimization procedure to optimally select the component values of a 2:1 on-chip SC converter. Implemented in a 32 nm SOI CMOS technology that features the high-density deep trench capacitor, the on-chip converter achieves 86% maximum efficiency at 4.6 W/mm2 power density while converting from a 1.8 V input voltage to 830 mV output voltage.
- 11 February 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 32 (1) , 363-377
Modeling and Pareto Optimization of On-Chip Switched Capacitor Converters
The operation and efficiency of on-chip switched-capacitor (SC) converters are highly affected by the parasitic bottom plate capacitor present in on-chip capacitor technologies. Existing modeling frameworks do not in a comprehensive manner take the effect of the bottom plate capacitor on converter operation and efficiency into account. This paper extends an existing SC state space modeling framework to include the bottom plate capacitor. The developed model is used in a Pareto optimization procedure to optimally select the component values of a 2:1 on-chip SC converter. Implemented in a 32 nm SOI CMOS technology that features the high-density deep trench capacitor, the on-chip converter achieves 86% maximum efficiency at 4.6 W/mm2 power density while converting from a 1.8 V input voltage to 830 mV output voltage.
- 1 January 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 408-409
23.6 A 30Gb/s 0.8pJ/b 14nm FinFET receiver data-path
The demand for energy-efficient I/O link transceivers operating at raw data-rates in the tens of Gb/s continues to fuel innovation in the field of wireline communication [1]. Receiving equalizers under one pJ/b are sought for chip-to-chip and chip-to-module links designed to operate across short-reach copper channels. Standards such as CEI-28G-VSR suit chip-to-module communication at raw data rates up to 28Gb/s and 10-12dB insertion loss at Nyquist. Proprietary and open standards in the same speed range are being developed too for data and memory-centric systems co-designed with CPUs and GPUs and channels with insertion loss on the order of 20dB [2].
- 1 January 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 408-409
23.6 A 30Gb/s 0.8pJ/b 14nm FinFET receiver data-path
The demand for energy-efficient I/O link transceivers operating at raw data-rates in the tens of Gb/s continues to fuel innovation in the field of wireline communication [1]. Receiving equalizers under one pJ/b are sought for chip-to-chip and chip-to-module links designed to operate across short-reach copper channels. Standards such as CEI-28G-VSR suit chip-to-module communication at raw data rates up to 28Gb/s and 10-12dB insertion loss at Nyquist. Proprietary and open standards in the same speed range are being developed too for data and memory-centric systems co-designed with CPUs and GPUs and channels with insertion loss on the order of 20dB [2].
- 31 August 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Terahertz Science and Technology
- Vol. 5 (6) , 902-913
Antenna-Coupled MOSFET Bolometers for Uncooled THz Sensing
In this paper, we present a comprehensive study on the operation of an antenna-coupled THz bolometer based on a micro-machined SOI-CMOS thermal sensor. The pixels are designed to operate at room temperature in vacuum. We focus on a new planar skirt antenna, which combines high sensitivity within a 0.6-1.2 THz band and 30 ° HPBW. We present an overview of the design considerations, as well as the characterization results which were obtained with both broadband and CW THz sources. The NEP of the pixel is of the order of 25 pW/Hz 1/2 , with responsivity 100 mA/W at the optimal operating point. The peak responsivity to a broadband THz signal is 600 mA/W. The ease of integration with a read-out circuit and the low power dissipation make this type of pixel a good candidate for focal plane array architecture.
- 31 August 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Terahertz Science and Technology
- Vol. 5 (6) , 902-913
Antenna-Coupled MOSFET Bolometers for Uncooled THz Sensing
In this paper, we present a comprehensive study on the operation of an antenna-coupled THz bolometer based on a micro-machined SOI-CMOS thermal sensor. The pixels are designed to operate at room temperature in vacuum. We focus on a new planar skirt antenna, which combines high sensitivity within a 0.6-1.2 THz band and 30 ° HPBW. We present an overview of the design considerations, as well as the characterization results which were obtained with both broadband and CW THz sources. The NEP of the pixel is of the order of 25 pW/Hz 1/2 , with responsivity 100 mA/W at the optimal operating point. The peak responsivity to a broadband THz signal is 600 mA/W. The ease of integration with a read-out circuit and the low power dissipation make this type of pixel a good candidate for focal plane array architecture.