Thomas Morf
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Thomas Morf has a total of 111 co-authors. Here are the top co-authors by number of shared publications:
Marcel Kossel
IBM Research-Zurich, 8803 Rueschlikon, Switzerland
17 shared publicationsChristian Menolfi
IBM Research-Zurich, 8803 Rüeschlikon, Switzerland. They are now with Cisco Systems, 8304 Zürich, Switzerland
16 shared publicationsPier Andrea Francese
IBM Research-Zurich, 8803 Rueschlikon, Switzerland
15 shared publications- Thomas Toifl
IBM Research Zürich, Rüschlikon, Switzerland
14 shared publications - Lukas Kull
IBM Research Zürich, Rüschlikon, Switzerland
13 shared publications Alessandro Cevrero
IBM Research-Zurich, 8803 Rüeschlikon, Switzerland. They are now with Cisco Systems, 8304 Zürich, Switzerland
10 shared publications
Latest Publications
- 14 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 61 (1) , 8-19
A 112-Gb/s Discrete Multitone Wireline Receiver Datapath With Time-Interleaved Time-Based ADC in 5-nm FinFET
This article presents a 112-Gb/s discrete multitone (DMT) wireline receiver (RX) datapath with a 50-GS/s, 8-bit, 64-way ( $8 \times 8$ ) time-interleaved time-based analog-to-digital converter (TI-TBADC) in a 5-nm FinFET. The TBADC converts the voltage input into a time-domain quantity using a ring oscillator (ROSC). Eight-slice TBADCs, driven from the same first-rank interleaver, share the identical injection-locked ROSC (IROSC) for voltage-to-time conversion (VTC). The DMT digital signal processor (DSP) achieves optimal bit and power loading with 63 orthogonal subchannels by employing a 64-way single-stage multi-path delay feedback (MDF) fast Fourier transform (FFT) core. An on-chip sign-sign least mean square (SS-LMS) engine adapts equalizer coefficients to combat channel fluctuation. The RX prototype demonstrates 4E-4 BER when communicating over the channel, exhibiting 18-dB insertion loss (IL) at Nyquist, while consuming 347-mW power and 0.242-mm2 silicon area.
- 14 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 61 (1) , 8-19
A 112-Gb/s Discrete Multitone Wireline Receiver Datapath With Time-Interleaved Time-Based ADC in 5-nm FinFET
This article presents a 112-Gb/s discrete multitone (DMT) wireline receiver (RX) datapath with a 50-GS/s, 8-bit, 64-way ( $8 \times 8$ ) time-interleaved time-based analog-to-digital converter (TI-TBADC) in a 5-nm FinFET. The TBADC converts the voltage input into a time-domain quantity using a ring oscillator (ROSC). Eight-slice TBADCs, driven from the same first-rank interleaver, share the identical injection-locked ROSC (IROSC) for voltage-to-time conversion (VTC). The DMT digital signal processor (DSP) achieves optimal bit and power loading with 63 orthogonal subchannels by employing a 64-way single-stage multi-path delay feedback (MDF) fast Fourier transform (FFT) core. An on-chip sign-sign least mean square (SS-LMS) engine adapts equalizer coefficients to combat channel fluctuation. The RX prototype demonstrates 4E-4 BER when communicating over the channel, exhibiting 18-dB insertion loss (IL) at Nyquist, while consuming 347-mW power and 0.242-mm2 silicon area.
- 27 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 71 (12) , 4889-4893
A Discrete Multitone Wireline Transceiver Datapath With On-Chip Sign-Sign LMS Adaptation and Loading Profile Optimization on RFSoC
This brief presents a discrete multi-tone (DMT) wireline transceiver (TRX) datapath and introduces the RFSoC-based real-time hardware platform to quickly sweep the optimum bit and power loading profile constrained by the peak-to-average-power ratio (PAPR). The datapath is implemented based on 32-parallel multi-path delay feedback (MDF) fast Fourier transform (FFT)/inverse FFT (IFFT) processors to save resources, integrating with the sign-sign least mean square (SS-LMS) engine. The loading is computed for the channel signal-to-noise ratio (SNR) and PAPR. The platform consists of 2.048 GS/s data converters, the DMT datapath implemented on programmable logic (PL) running at 64 MHz, and the channel board. This system enables a quick bit-error-rate (BER) test at an order of 1.0E-9, accelerating the finding of optimal loading with realistic hardware effects and random clipping events. Experimental results show that the data rate could reach a maximum of 6.82 Gb/s at a BER of 5.7E-4 and a minimum BER of 3.7E-7 for a target data rate of 4.81 Gb/s with a channel exhibiting 16.3 dB insertion loss (IL) at Nyquist.
- 27 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 71 (12) , 4889-4893
A Discrete Multitone Wireline Transceiver Datapath With On-Chip Sign-Sign LMS Adaptation and Loading Profile Optimization on RFSoC
This brief presents a discrete multi-tone (DMT) wireline transceiver (TRX) datapath and introduces the RFSoC-based real-time hardware platform to quickly sweep the optimum bit and power loading profile constrained by the peak-to-average-power ratio (PAPR). The datapath is implemented based on 32-parallel multi-path delay feedback (MDF) fast Fourier transform (FFT)/inverse FFT (IFFT) processors to save resources, integrating with the sign-sign least mean square (SS-LMS) engine. The loading is computed for the channel signal-to-noise ratio (SNR) and PAPR. The platform consists of 2.048 GS/s data converters, the DMT datapath implemented on programmable logic (PL) running at 64 MHz, and the channel board. This system enables a quick bit-error-rate (BER) test at an order of 1.0E-9, accelerating the finding of optimal loading with realistic hardware effects and random clipping events. Experimental results show that the data rate could reach a maximum of 6.82 Gb/s at a BER of 5.7E-4 and a minimum BER of 3.7E-7 for a target data rate of 4.81 Gb/s with a channel exhibiting 16.3 dB insertion loss (IL) at Nyquist.
- 7 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 71 (11) , 5115-5128
A Loop-Break Decision Feedback Equalizer for DAC/ADC-DSP-Based Wireline Transceivers
This paper presents a novel digital decision feedback equalizer (DFE) design that can relax the feedback timing constraints for analog-to-digital converter (ADC)-based high-speed wireline receivers. The proposed technique breaks the loop-unrolled DFE (LU-DFE) chain by computing multiple LU-DFE chains in parallel with all possible seed symbols, and selecting the appropriate output by the post-processing selection logic. The proposed loop-break DFE (LB-DFE) is functionally equivalent to the conventional DFE with any other implementation techniques such as LU-DFE, look-ahead DFE (LA-DFE), or direct DFE. With topographical synthesis in 28nm CMOS process, the proposed LB-DFE achieved up to 54% of DFE area saving as compared to LA-DFE with look-ahead factor (LF) of 16 for 112Gb/s PAM-4 with 875MHz DSP clock speed. The implementation feasibility and functionality are verified using ZCU111 RFSoC platform at 6Gb/s (3GS/s ADC conversion rate) with a channel exhibiting 25dB loss at 1.5GHz, demonstrating the same bit error rate (BER) performance between the LB-DFE and the LA-DFE. Equipment-based measurements using arbitrary waveform generator (AWG) and real-time oscilloscope transmitting/receiving 40GBaud PAM-4 (80Gb/s) to/from the differential cables with software 21-tap feed-forward equalizer (FFE) and LB-DFE on PC was also conducted.
- 7 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 71 (11) , 5115-5128
A Loop-Break Decision Feedback Equalizer for DAC/ADC-DSP-Based Wireline Transceivers
This paper presents a novel digital decision feedback equalizer (DFE) design that can relax the feedback timing constraints for analog-to-digital converter (ADC)-based high-speed wireline receivers. The proposed technique breaks the loop-unrolled DFE (LU-DFE) chain by computing multiple LU-DFE chains in parallel with all possible seed symbols, and selecting the appropriate output by the post-processing selection logic. The proposed loop-break DFE (LB-DFE) is functionally equivalent to the conventional DFE with any other implementation techniques such as LU-DFE, look-ahead DFE (LA-DFE), or direct DFE. With topographical synthesis in 28nm CMOS process, the proposed LB-DFE achieved up to 54% of DFE area saving as compared to LA-DFE with look-ahead factor (LF) of 16 for 112Gb/s PAM-4 with 875MHz DSP clock speed. The implementation feasibility and functionality are verified using ZCU111 RFSoC platform at 6Gb/s (3GS/s ADC conversion rate) with a channel exhibiting 25dB loss at 1.5GHz, demonstrating the same bit error rate (BER) performance between the LB-DFE and the LA-DFE. Equipment-based measurements using arbitrary waveform generator (AWG) and real-time oscilloscope transmitting/receiving 40GBaud PAM-4 (80Gb/s) to/from the differential cables with software 21-tap feed-forward equalizer (FFE) and LB-DFE on PC was also conducted.
- 6 June 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 71 (11) , 4738-4742
A 2-Lane Discrete Multitone Wireline Receiver Datapath With Far-End Crosstalk Cancellation on RFSoC Platform
This brief presents a 2-lane discrete multitone (DMT) wireline receiver (RX) with a far-end crosstalk (FEXT) cancellation and its implementation on the ZCU111 RFSoC evaluation board for real-time functional verification. The RX datapath is implemented with the 64-parallel 128-tap multi-path delay-feedback (MDF) fast Fourier transform (FFT) to optimize resources and throughput. The multiple-input, multiple-output (MIMO) frequency-domain equalizer (FDE) compensates both channel insertion loss (IL) and FEXT based on coefficients computed from an on-chip pilot-assist channel estimation (CHEST). The platform includes a programmable logic (PL) for a DMT digital signal processor (DSP) running at 32 MHz, 2.048 GS/s data converters, and intersymbol interference (ISI)/FEXT board. This system enables the reflection of a realistic hardware impairment and real-time transceiver (TRX) operation with a quick bit error rate (BER) test. The measurement demonstrates that the MIMO DMT significantly improves a BER from 1.0E-2 to 5.8E-7 when the FEXT is canceled for a channel exhibiting 15 dB of IL and 10 dB of IL-to-crosstalk ratio (ICR) at Nyquist frequency.
- 6 June 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 71 (11) , 4738-4742
A 2-Lane Discrete Multitone Wireline Receiver Datapath With Far-End Crosstalk Cancellation on RFSoC Platform
This brief presents a 2-lane discrete multitone (DMT) wireline receiver (RX) with a far-end crosstalk (FEXT) cancellation and its implementation on the ZCU111 RFSoC evaluation board for real-time functional verification. The RX datapath is implemented with the 64-parallel 128-tap multi-path delay-feedback (MDF) fast Fourier transform (FFT) to optimize resources and throughput. The multiple-input, multiple-output (MIMO) frequency-domain equalizer (FDE) compensates both channel insertion loss (IL) and FEXT based on coefficients computed from an on-chip pilot-assist channel estimation (CHEST). The platform includes a programmable logic (PL) for a DMT digital signal processor (DSP) running at 32 MHz, 2.048 GS/s data converters, and intersymbol interference (ISI)/FEXT board. This system enables the reflection of a realistic hardware impairment and real-time transceiver (TRX) operation with a quick bit error rate (BER) test. The measurement demonstrates that the MIMO DMT significantly improves a BER from 1.0E-2 to 5.8E-7 when the FEXT is canceled for a channel exhibiting 15 dB of IL and 10 dB of IL-to-crosstalk ratio (ICR) at Nyquist frequency.
- 5 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 71 (7) , 3318-3322
A DAC/ADC-Based Wireline Transceiver Datapath Functional Verification on RFSoC Platform
This brief presents an RFSoC-based functional verification platform for a 2-lane pulse amplitude modulation (PAM) transceiver (TRX) datapath supporting 4-level PAM (PAM-4) and 8-level PAM (PAM-8). Digital-to-analog converters (DACs) and analog-to-digital converters (ADCs) existing on the ZU28DR RFSoC are used as digital front-ends of the transmitter (TX) and the receiver (RX), respectively. All digital equalization circuits and adaptation engines required for the modern >112 Gb/s DAC/ADC-DSP-based TRX datapath (excluding clock recovery) are implemented on the programmable logic (PL) running at 50 MHz, enabling real-time functional verification of the DAC/ADC-DSP-based serializer-deserializer (SerDes) operation. The register-transfer-level (RTL) design of the DSP can be directly used for the TRX silicon tape-out once the design is verified with the proposed RFSoC-based platform. The proposed system demonstrates a complete real-time functional verification of the TRX datapath, including the bit-error-rate (BER) test with the BER lower than 10-9 at 6.4 Gb/s and 9.6 Gb/s for PAM-4/8 symbols, respectively, with a channel loss of 18 dB at 1.6 GHz.
- 5 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 71 (7) , 3318-3322
A DAC/ADC-Based Wireline Transceiver Datapath Functional Verification on RFSoC Platform
This brief presents an RFSoC-based functional verification platform for a 2-lane pulse amplitude modulation (PAM) transceiver (TRX) datapath supporting 4-level PAM (PAM-4) and 8-level PAM (PAM-8). Digital-to-analog converters (DACs) and analog-to-digital converters (ADCs) existing on the ZU28DR RFSoC are used as digital front-ends of the transmitter (TX) and the receiver (RX), respectively. All digital equalization circuits and adaptation engines required for the modern >112 Gb/s DAC/ADC-DSP-based TRX datapath (excluding clock recovery) are implemented on the programmable logic (PL) running at 50 MHz, enabling real-time functional verification of the DAC/ADC-DSP-based serializer-deserializer (SerDes) operation. The register-transfer-level (RTL) design of the DSP can be directly used for the TRX silicon tape-out once the design is verified with the proposed RFSoC-based platform. The proposed system demonstrates a complete real-time functional verification of the TRX datapath, including the bit-error-rate (BER) test with the BER lower than 10-9 at 6.4 Gb/s and 9.6 Gb/s for PAM-4/8 symbols, respectively, with a channel loss of 18 dB at 1.6 GHz.
- 7 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Solid-State Circuits Letters
- Vol. 6, 193-196
An 8b 1.0-to-1.25 GS/s Time-Based ADC With Bipolar VTC and Sense Amplifier Latch Interpolated Gated Ring Oscillator TDC
An 8-bit digital intensive time-based ADC implemented in 5nm CMOS is presented in this work. It proposes a bipolar ramp-based voltage-to-time converter (BVTC) to eliminate the reference voltage and to allow a wide input swing of 0.75Vpp,diff. A redundancy scheme for the input polarity decision taken for 1-bit voltage domain folding is introduced against wrong decisions which eliminates comparator calibration in analog domain and allows a more efficient design. Sense amplifier latch (SAL) interpolation technique is presented which reduces the power and area consumption when phase interpolating the time-to-digital converter (TDC) signals. The ADC reaches 1GS/s sampling rate with 0.7V supply and 1.25GS/s with 0.8V supply and achieves 16.6fJ/conv-step and 20.3fJ/conv-step Walden FoM respectively. The total active area is 313μm2.
- 7 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Solid-State Circuits Letters
- Vol. 6, 193-196
An 8b 1.0-to-1.25 GS/s Time-Based ADC With Bipolar VTC and Sense Amplifier Latch Interpolated Gated Ring Oscillator TDC
An 8-bit digital intensive time-based ADC implemented in 5nm CMOS is presented in this work. It proposes a bipolar ramp-based voltage-to-time converter (BVTC) to eliminate the reference voltage and to allow a wide input swing of 0.75Vpp,diff. A redundancy scheme for the input polarity decision taken for 1-bit voltage domain folding is introduced against wrong decisions which eliminates comparator calibration in analog domain and allows a more efficient design. Sense amplifier latch (SAL) interpolation technique is presented which reduces the power and area consumption when phase interpolating the time-to-digital converter (TDC) signals. The ADC reaches 1GS/s sampling rate with 0.7V supply and 1.25GS/s with 0.8V supply and achieves 16.6fJ/conv-step and 20.3fJ/conv-step Walden FoM respectively. The total active area is 313μm2.
- 23 December 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 58 (4) , 1074-1086
A 72-GS/s, 8-Bit DAC-Based Wireline Transmitter in 4-nm FinFET CMOS for 200+ Gb/s Serial Links
This article details the design and measurement of a digital-to-analog converter (DAC)-based source-series terminated (SST) transmitter (TX) for wireline applications in 4-nm FinFET CMOS technology. The DAC achieves 8-bit resolution and high analog output bandwidth by using a segmented architecture along with a single-ended LSB. Strength adjustment of the lower four DAC LSBs relative to the upper four DAC MSBs is accomplished with a hybrid analog/digital tuning approach, which overcomes minimum device-size limitations that can limit the effectiveness of pure digital tuning for SST drivers. The resulting DAC design achieves well-matched MSB/LSB segments with $-$ 0.63/0.67 LSB integral nonlinearity (INL) and $-$ 0.16/0.43 LSB differential nonlinearity (DNL). Time-domain modulation of 216-Gb/s PAM8 and frequency-domain modulation of 212-Gb/s orthogonal frequency-division multiplexing (OFDM) are reported, demonstrating the capability of CMOS DACs to support frequency-domain modulation for wireline applications. The TX consumes 288 mW from a 0.95-V power supply.
- 23 December 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 58 (4) , 1074-1086
A 72-GS/s, 8-Bit DAC-Based Wireline Transmitter in 4-nm FinFET CMOS for 200+ Gb/s Serial Links
This article details the design and measurement of a digital-to-analog converter (DAC)-based source-series terminated (SST) transmitter (TX) for wireline applications in 4-nm FinFET CMOS technology. The DAC achieves 8-bit resolution and high analog output bandwidth by using a segmented architecture along with a single-ended LSB. Strength adjustment of the lower four DAC LSBs relative to the upper four DAC MSBs is accomplished with a hybrid analog/digital tuning approach, which overcomes minimum device-size limitations that can limit the effectiveness of pure digital tuning for SST drivers. The resulting DAC design achieves well-matched MSB/LSB segments with $-$ 0.63/0.67 LSB integral nonlinearity (INL) and $-$ 0.16/0.43 LSB differential nonlinearity (DNL). Time-domain modulation of 216-Gb/s PAM8 and frequency-domain modulation of 212-Gb/s orthogonal frequency-division multiplexing (OFDM) are reported, demonstrating the capability of CMOS DACs to support frequency-domain modulation for wireline applications. The TX consumes 288 mW from a 0.95-V power supply.
- Open Access
- 12 May 2021
- Published by MDPI AG in Electronics
- Vol. 10 (10) , 1150
Experimental Efficiency Evaluation of Stacked Transistor Half-Bridge Topologies in 14 nm CMOS Technology
Different Half-Bridge (HB) converter topologies for an Integrated Voltage Regulator (IVR), which serves as a microprocessor application, were evaluated. The HB circuits were implemented with Stacked Transistors (HBSTs) in a cutting-edge 14 nm CMOS technology node in order to enable the integration on the microprocessor die. Compared to a conventional realization of the HBST, it was found that the Active Neutral-Point Clamped (ANPC) HBST topology with Independent Clamp Switches (ICSs) not only ensured balanced blocking voltages across the series-connected transistors, but also featured a more robust operation and achieved higher efficiencies at high output currents. The IVR achieved a maximum efficiency of 85.3% at an output current of 300 mA and a switching frequency of 50 MHz. At the maximum measured output current of 780 mA, the efficiency was 83.1%. The active part of the IVR (power switches, gate-drivers, and level shifters) realized a high maximum current density of 24.7 A/mm.- 12 May 2021
- Published by MDPI AG in Electronics
- Vol. 10 (10) , 1150
Open AccessExperimental Efficiency Evaluation of Stacked Transistor Half-Bridge Topologies in 14 nm CMOS Technology
Different Half-Bridge (HB) converter topologies for an Integrated Voltage Regulator (IVR), which serves as a microprocessor application, were evaluated. The HB circuits were implemented with Stacked Transistors (HBSTs) in a cutting-edge 14 nm CMOS technology node in order to enable the integration on the microprocessor die. Compared to a conventional realization of the HBST, it was found that the Active Neutral-Point Clamped (ANPC) HBST topology with Independent Clamp Switches (ICSs) not only ensured balanced blocking voltages across the series-connected transistors, but also featured a more robust operation and achieved higher efficiencies at high output currents. The IVR achieved a maximum efficiency of 85.3% at an output current of 300 mA and a switching frequency of 50 MHz. At the maximum measured output current of 780 mA, the efficiency was 83.1%. The active part of the IVR (power switches, gate-drivers, and level shifters) realized a high maximum current density of 24.7 A/mm. - Open Access
- 22 September 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Power Electronics
- Vol. 1, 456-468
Electrical and Thermal Characterization of an Inductor-Based ANPC-Type Buck Converter in 14 nm CMOS Technology for Microprocessor Applications
Integrated Voltage Regulators (IVRs) are attractive substitutes for conventional voltage regulators located on the motherboards, due to outstanding dynamic performances and superior power densities. IVRs operate with switching frequencies in the range of 100 MHz and are assembled in highly compact packages close to the microprocessor load. This paper presents a comprehensive characterization of a PCB and inductor-based four-phase ANPC-type IVR that uses a Power Management IC (PMIC) implemented in a 14 nm CMOS technology node. The characterization is based on the results of electrical measurements, thermal inspections of the chip surface, and simulations, which enables the separation of the total losses into on-chip and off-chip loss components and the allocation of important loss components inside the chip. The investigated IVR achieves a maximum efficiency of 84.1% at an output power of P out = 640 mW and a switching frequency of f s = 50 MHz. The thermal measurements reveal that the maximum efficiency of the PMIC itself is between 88 % and 90 % at f s = 50 MHz and P out ∈ [500 mW, 600 mW]; at P out = 890 mW, a chip current density of 24.7 A/mm 2 is achieved. The findings in particular point out that the losses in the chip-internal interconnections, i.e., the conductors of the Power Distribution Network (PDN) and the twelve stacked metal layers below the PDN, have a substantial contribution to the total losses. Furthermore, the combination of Cadence post-layout simulations with impedance networks obtained from an appropriate software tool, e.g., FastHenry, is found to establish a suitable toolbox for estimating losses in IVRs.
- 22 September 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Power Electronics
- Vol. 1, 456-468
Open AccessElectrical and Thermal Characterization of an Inductor-Based ANPC-Type Buck Converter in 14 nm CMOS Technology for Microprocessor Applications
Integrated Voltage Regulators (IVRs) are attractive substitutes for conventional voltage regulators located on the motherboards, due to outstanding dynamic performances and superior power densities. IVRs operate with switching frequencies in the range of 100 MHz and are assembled in highly compact packages close to the microprocessor load. This paper presents a comprehensive characterization of a PCB and inductor-based four-phase ANPC-type IVR that uses a Power Management IC (PMIC) implemented in a 14 nm CMOS technology node. The characterization is based on the results of electrical measurements, thermal inspections of the chip surface, and simulations, which enables the separation of the total losses into on-chip and off-chip loss components and the allocation of important loss components inside the chip. The investigated IVR achieves a maximum efficiency of 84.1% at an output power of P out = 640 mW and a switching frequency of f s = 50 MHz. The thermal measurements reveal that the maximum efficiency of the PMIC itself is between 88 % and 90 % at f s = 50 MHz and P out ∈ [500 mW, 600 mW]; at P out = 890 mW, a chip current density of 24.7 A/mm 2 is achieved. The findings in particular point out that the losses in the chip-internal interconnections, i.e., the conductors of the Power Distribution Network (PDN) and the twelve stacked metal layers below the PDN, have a substantial contribution to the total losses. Furthermore, the combination of Cadence post-layout simulations with impedance networks obtained from an appropriate software tool, e.g., FastHenry, is found to establish a suitable toolbox for estimating losses in IVRs.
- 30 June 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Solid-State Circuits Letters
- Vol. 3, 94-97
An In-Comparator Aperture-Time Equalization in a 7-nm FinFET CMOS 40-Gb/s Receiver
This paper proposes an in-comparator aperture-time equalization scheme using the impulse response of a clocked comparator. The technique is applied in a wireline link receiver prototype, implemented in CMOS 7nm FinFET technology. The proposed method controls the aperture properties of the slicers by shaping their impulse sensitivity functions. We demonstrate an aperture skew control range of 4.7ps with 147fs accuracy for NRZ signaling at 40Gb/s. PAM4 signaling at 80Gb/s is also showcased using the proposed technique. These results serve as a proof of concept for next-generation source-synchronous chip-to-chip dense I/O links where aperture-time skews could be fine adjusted inside each comparator.
- 30 June 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Solid-State Circuits Letters
- Vol. 3, 94-97
An In-Comparator Aperture-Time Equalization in a 7-nm FinFET CMOS 40-Gb/s Receiver
This paper proposes an in-comparator aperture-time equalization scheme using the impulse response of a clocked comparator. The technique is applied in a wireline link receiver prototype, implemented in CMOS 7nm FinFET technology. The proposed method controls the aperture properties of the slicers by shaping their impulse sensitivity functions. We demonstrate an aperture skew control range of 4.7ps with 147fs accuracy for NRZ signaling at 40Gb/s. PAM4 signaling at 80Gb/s is also showcased using the proposed technique. These results serve as a proof of concept for next-generation source-synchronous chip-to-chip dense I/O links where aperture-time skews could be fine adjusted inside each comparator.