Joseph Staudinger
Research Subjects
Joseph Staudinger has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
- Chun-Wei Chang
Department of Engineering Science and Ocean Engineering, National Taiwan University, Taipei, Taiwan
6 shared publications - Jau-Horng Chen
Department of Engineering Science and Ocean Engineering, National Taiwan University, Taipei, Taiwan
6 shared publications Damon G. Holmes
NXP Semiconductors, Chandler, AZ 85224, USA
2 shared publicationsShu-Chen Lin
Department of Engineering Science and Ocean Engineering, National Taiwan University, Taipei, Taiwan
2 shared publications- Shu-Chen Lin
Department of Engineering Science and Ocean Engineering, National Taiwan University, Taipei, Taiwan
2 shared publications - Shuo-Heng Xu
Department of Engineering Science and Ocean Engineering, National Taiwan University, Taipei, Taiwan
2 shared publications
Latest Publications
- 3 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 33 (12) , 1654-1657
A Wideband Pulse-Modulated Polar Transmitter With Low-Complexity Digital Predistortion
In this letter, a wide bandwidth power amplifier (PA) using pulse modulation is presented. Pulse modulation significantly reduces the amount of thermal memory. However, with a large signal bandwidth, significant matching-related memory effect exists. A compensation equalization filter is proposed to compensate the in-band gain/phase variation, such that simple memoryless digital predistortion (DPD) can still be utilized. A prototype transmitter system is constructed using a commercially available base station PA for validation. Measurements are performed using a 256-QAM fifth-generation new radio (5G NR) downlink multicarrier modulated signal at 3500 MHz with an instantaneous bandwidth of 100 MHz. Using memoryless DPD and the proposed filter, the overall system achieved passing the $-$ 45-dBc downlink spectral requirements for the 5G NR standard showing negligible thermal memory effect in PAs using pulse modulation.
- 3 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 33 (12) , 1654-1657
A Wideband Pulse-Modulated Polar Transmitter With Low-Complexity Digital Predistortion
In this letter, a wide bandwidth power amplifier (PA) using pulse modulation is presented. Pulse modulation significantly reduces the amount of thermal memory. However, with a large signal bandwidth, significant matching-related memory effect exists. A compensation equalization filter is proposed to compensate the in-band gain/phase variation, such that simple memoryless digital predistortion (DPD) can still be utilized. A prototype transmitter system is constructed using a commercially available base station PA for validation. Measurements are performed using a 256-QAM fifth-generation new radio (5G NR) downlink multicarrier modulated signal at 3500 MHz with an instantaneous bandwidth of 100 MHz. Using memoryless DPD and the proposed filter, the overall system achieved passing the $-$ 45-dBc downlink spectral requirements for the 5G NR standard showing negligible thermal memory effect in PAs using pulse modulation.
- Open Access
- 9 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 58055-58063
A Digital Combining Applied to the Multilevel Pulse Modulated Polar Transmitter
This paper presents a novel digital combining method to implement a multilevel pulse modulation polar transmitter (PMPT) for 5G NR base station applications. Using pulse-width modulation on switch mode power amplifiers (PAs) is a promising method for PA efficiency improvement. Whereas using the interleaved multilevel architecture can eliminate unwanted harmonics. Previous PMPT implementations used passive power combiners to combine multiple PA outputs, this paper proposes combining to be performed digitally prior to the PAs. It was shown the proposed method is no longer susceptible to PA mismatch and is highly suitable for Doherty power amplifiers (DPAs). A transmitter prototype was developed and evaluated with a 256-QAM 5G NR 20-MHz instantaneous bandwidth signal centered at 2140 MHz. The overall system achieved 39.4 dBm with a power-added efficiency of 39%. It passes the 5G NR adjacent channel leakage ratio (ACLR) downlink spectral requirement with only memoryless digital predistortion.
- 9 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 58055-58063
Open AccessA Digital Combining Applied to the Multilevel Pulse Modulated Polar Transmitter
This paper presents a novel digital combining method to implement a multilevel pulse modulation polar transmitter (PMPT) for 5G NR base station applications. Using pulse-width modulation on switch mode power amplifiers (PAs) is a promising method for PA efficiency improvement. Whereas using the interleaved multilevel architecture can eliminate unwanted harmonics. Previous PMPT implementations used passive power combiners to combine multiple PA outputs, this paper proposes combining to be performed digitally prior to the PAs. It was shown the proposed method is no longer susceptible to PA mismatch and is highly suitable for Doherty power amplifiers (DPAs). A transmitter prototype was developed and evaluated with a 256-QAM 5G NR 20-MHz instantaneous bandwidth signal centered at 2140 MHz. The overall system achieved 39.4 dBm with a power-added efficiency of 39%. It passes the 5G NR adjacent channel leakage ratio (ACLR) downlink spectral requirement with only memoryless digital predistortion.
- 11 April 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave Magazine
- Vol. 24 (5) , 136-137
The MicroApps Seminars
- 11 April 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave Magazine
- Vol. 24 (5) , 136-137
The MicroApps Seminars
- 10 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Components Letters
- Vol. 31 (7) , 881-884
2.6-GHz Integrated LDMOS Doherty Power Amplifier for 5G Basestation Applications
This letter presents a compact output combining network for a packaged integrated asymmetric Doherty Power Amplifier (DPA). The combining network uses a new method for absorbing part of the peaking amplifier’s Cds into the impedance transformer, thus extending the C-L-C based “Cds absorption" technique to asymmetric DPAs. Based on the proposed combining network, a two-stage LDMOS integrated asymmetric DPA was designed and fabricated at 2.6 GHz. The fabricated IC is mounted in a quad flat no-lead (QFN) package. Under a single-tone continuous-wave (CW) signal at 2.6 GHz, the DPA achieves peak power of 46 dBm, linear gain of 31.7 dB and 48% power-added efficiency (PAE) at 8 dB output power back-off (OBO). The DPA also demonstrates good linearizability by meeting the 5G spectrum mask and achieving a DPD corrected ACPR better than -51dBc for 160 MHz long term evolution (LTE).
- 10 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Components Letters
- Vol. 31 (7) , 881-884
2.6-GHz Integrated LDMOS Doherty Power Amplifier for 5G Basestation Applications
This letter presents a compact output combining network for a packaged integrated asymmetric Doherty Power Amplifier (DPA). The combining network uses a new method for absorbing part of the peaking amplifier’s Cds into the impedance transformer, thus extending the C-L-C based “Cds absorption" technique to asymmetric DPAs. Based on the proposed combining network, a two-stage LDMOS integrated asymmetric DPA was designed and fabricated at 2.6 GHz. The fabricated IC is mounted in a quad flat no-lead (QFN) package. Under a single-tone continuous-wave (CW) signal at 2.6 GHz, the DPA achieves peak power of 46 dBm, linear gain of 31.7 dB and 48% power-added efficiency (PAE) at 8 dB output power back-off (OBO). The DPA also demonstrates good linearizability by meeting the 5G spectrum mask and achieving a DPD corrected ACPR better than -51dBc for 160 MHz long term evolution (LTE).
- 6 August 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 68 (10) , 4216-4228
Modeling of Input Nonlinearity and Waveform Engineered High-Efficiency Class-F Power Amplifiers
A comprehensive time-domain modeling and a generalized design methodology for input and output waveform engineered Class-F power amplifiers (PAs) are presented in this article. A closed-form relationship between input nonlinearity and second harmonic source impedance (Z2S) termination is presented from which efficiency and output power performance are predicted for Class-F PAs. The maximum, minimum, and safe Z2S design space for a Class-F PA are identified. Moreover, the derived design equations show that the typical fundamental load of a Class-F PA operation must be re-engineered in the presence of input nonlinearity in order to achieve optimum efficiency performance. The theoretical analyses are first validated with pulsed vector load-pull (VLP) measurements with a gallium nitride (GaN) 2 mm device. Then, high-power (210 W) GaN 24-mm devices with in-package Z2S terminations are implemented. Measurement results with the new source and load design space show efficiency improvement of 4.4% compared to the nominal Class-F PA.
- 6 August 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 68 (10) , 4216-4228
Modeling of Input Nonlinearity and Waveform Engineered High-Efficiency Class-F Power Amplifiers
A comprehensive time-domain modeling and a generalized design methodology for input and output waveform engineered Class-F power amplifiers (PAs) are presented in this article. A closed-form relationship between input nonlinearity and second harmonic source impedance (Z2S) termination is presented from which efficiency and output power performance are predicted for Class-F PAs. The maximum, minimum, and safe Z2S design space for a Class-F PA are identified. Moreover, the derived design equations show that the typical fundamental load of a Class-F PA operation must be re-engineered in the presence of input nonlinearity in order to achieve optimum efficiency performance. The theoretical analyses are first validated with pulsed vector load-pull (VLP) measurements with a gallium nitride (GaN) 2 mm device. Then, high-power (210 W) GaN 24-mm devices with in-package Z2S terminations are implemented. Measurement results with the new source and load design space show efficiency improvement of 4.4% compared to the nominal Class-F PA.
- 8 March 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Components Letters
- Vol. 29 (4) , 285-287
On the Thermal Memory Effect Reduction of Power Amplifiers Using Pulse Modulation
- 8 March 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Components Letters
- Vol. 29 (4) , 285-287
On the Thermal Memory Effect Reduction of Power Amplifiers Using Pulse Modulation
- 17 December 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 67 (3) , 1107-1114
A Multiphase Digital Pulsewidth Modulated Polar Transmitter Architecture With Reactive Combiner for Improved Efficiency
This paper presents a new method of reactive-combiner structure to be used as part of a multiphase digital pulsewidth modulated polar transmitter (DPWMPT). It overcomes the limitations of previous implementations of the multiphase pulse-modulated polar transmitter related to terminating pulsewidth modulation (PWM) harmonics located outside the passband, thereby improving both PWM harmonic suppression by using multiphase aliasing-free digital PWM technique and increasing overall efficiency by using reactive combining. For validation, a prototype transmitter was implemented and tested with a 64-QAM 20-MHz bandwidth long-term evolution (LTE) downlink signal with a 7.5-dB peak-to-average power ratio at 2140 MHz. The prototype dual-phase DPWMPT architecture achieved an output power level of 37 dBm and power-added efficiency of 33.5% while passing the stringent spectral requirements of the LTE standard for small-cell base stations using only simply memoryless predistortion correction.
- 17 December 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 67 (3) , 1107-1114
A Multiphase Digital Pulsewidth Modulated Polar Transmitter Architecture With Reactive Combiner for Improved Efficiency
This paper presents a new method of reactive-combiner structure to be used as part of a multiphase digital pulsewidth modulated polar transmitter (DPWMPT). It overcomes the limitations of previous implementations of the multiphase pulse-modulated polar transmitter related to terminating pulsewidth modulation (PWM) harmonics located outside the passband, thereby improving both PWM harmonic suppression by using multiphase aliasing-free digital PWM technique and increasing overall efficiency by using reactive combining. For validation, a prototype transmitter was implemented and tested with a 64-QAM 20-MHz bandwidth long-term evolution (LTE) downlink signal with a 7.5-dB peak-to-average power ratio at 2140 MHz. The prototype dual-phase DPWMPT architecture achieved an output power level of 37 dBm and power-added efficiency of 33.5% while passing the stringent spectral requirements of the LTE standard for small-cell base stations using only simply memoryless predistortion correction.
- 28 August 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Components Letters
- Vol. 28 (10) , 933-935
A Multilevel Pulse-Modulated Polar Transmitter Based on a Doherty Power Amplifier and Memoryless Digital Predistortion
This letter presents an aliasing free multilevel pulse modulation (MLPM) architecture to implement a linear Doherty power amplifier (PA). This letter is believed to be the first reported results of this type of Doherty architecture to achieve linear amplification rather than the usual situation of a continuous amplitude modulated carrier and continuous load modulation. Our results show that both high efficiency and good linearization can be achieved with simple memoryless digital predistortion. Doherty operation with MLPM is believed to have benefits in linearization due to the MLPM discrete drive as less power is dissipated by the PA, leading to less thermal-related memory effects. A prototype transmitter system is constructed using a commercially available Doherty PA for validation. Measurements are performed using a 64-QAM long-term evolution (LTE) downlink signal at 2140 MHz with 20-MHz bandwidth. The overall system achieved an output power level of 40.1 dBm with a power-added efficiency of 39.5% while passing the -45-dBc downlink spectral requirements of the LTE standard.
- 28 August 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Components Letters
- Vol. 28 (10) , 933-935
A Multilevel Pulse-Modulated Polar Transmitter Based on a Doherty Power Amplifier and Memoryless Digital Predistortion
This letter presents an aliasing free multilevel pulse modulation (MLPM) architecture to implement a linear Doherty power amplifier (PA). This letter is believed to be the first reported results of this type of Doherty architecture to achieve linear amplification rather than the usual situation of a continuous amplitude modulated carrier and continuous load modulation. Our results show that both high efficiency and good linearization can be achieved with simple memoryless digital predistortion. Doherty operation with MLPM is believed to have benefits in linearization due to the MLPM discrete drive as less power is dissipated by the PA, leading to less thermal-related memory effects. A prototype transmitter system is constructed using a commercially available Doherty PA for validation. Measurements are performed using a 64-QAM long-term evolution (LTE) downlink signal at 2140 MHz with 20-MHz bandwidth. The overall system achieved an output power level of 40.1 dBm with a power-added efficiency of 39.5% while passing the -45-dBc downlink spectral requirements of the LTE standard.
- 15 June 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Components Letters
- Vol. 28 (8) , 729-731
A Highly Linear Pulse-Modulated Polar Transmitter Using Aliasing-Free Digital PWM for Small-Cell Base Stations
This letter presents a broadband power amplifier (PA) for improving the linearity of an aliasing-free pulse-modulated polar transmitter. For this letter, a broadband input matching deep class-C PA is designed. The input matching bandwidth is over 650 MHz around the center frequency. To validate the proposed system, a prototype transmitter system is constructed using commercially available components. The overall system achieved an output power level of 35.5 dBm with a power-added efficiency of 32.8%. Spectral requirements using a 10-MHz bandwidth 64-QAM long-term evolution downlink signal at 2140 MHz was passed for small-cell base stations without the use of any digital predistortion techniques.
- 15 June 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Components Letters
- Vol. 28 (8) , 729-731
A Highly Linear Pulse-Modulated Polar Transmitter Using Aliasing-Free Digital PWM for Small-Cell Base Stations
This letter presents a broadband power amplifier (PA) for improving the linearity of an aliasing-free pulse-modulated polar transmitter. For this letter, a broadband input matching deep class-C PA is designed. The input matching bandwidth is over 650 MHz around the center frequency. To validate the proposed system, a prototype transmitter system is constructed using commercially available components. The overall system achieved an output power level of 35.5 dBm with a power-added efficiency of 32.8%. Spectral requirements using a 10-MHz bandwidth 64-QAM long-term evolution downlink signal at 2140 MHz was passed for small-cell base stations without the use of any digital predistortion techniques.
- 1 June 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Components Letters
- Vol. 28 (7) , 600-602
On the Second-Harmonic Null in Design Space of Power Amplifiers
This letter investigates the source of performance degradation and efficiency null that is traditionally observed during second-harmonic load pull of active power transistors. A theory that explains the performance degradation is presented, resulting in a simplified closed-form equation that predicts the location of performance null for different device peripheries and/or design frequencies. Thereafter, the intrinsic drain waveforms for null and maximum efficiency are analyzed to study potential causes for efficiency degradation. The theory is validated using active load-pull measurements of laterally diffused metal-oxide-semiconductor and gallium nitride active devices for different peripheries (0.5-4.8 mm) at various frequencies of operation (2, 2.6, and 3.5 GHz).
- 1 June 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Components Letters
- Vol. 28 (7) , 600-602
On the Second-Harmonic Null in Design Space of Power Amplifiers
This letter investigates the source of performance degradation and efficiency null that is traditionally observed during second-harmonic load pull of active power transistors. A theory that explains the performance degradation is presented, resulting in a simplified closed-form equation that predicts the location of performance null for different device peripheries and/or design frequencies. Thereafter, the intrinsic drain waveforms for null and maximum efficiency are analyzed to study potential causes for efficiency degradation. The theory is validated using active load-pull measurements of laterally diffused metal-oxide-semiconductor and gallium nitride active devices for different peripheries (0.5-4.8 mm) at various frequencies of operation (2, 2.6, and 3.5 GHz).