Yuefeng Hou
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Yuefeng Hou has a total of 78 co-authors. Here are the top co-authors by number of shared publications:
- Kaixue Ma
Tianjin University
30 shared publications - Yue Li
Department of Electronic Engineering, Beijing National Research Center for Information Science and Technology, State Key Laboratory of Space Network and Communications, Tsinghua University, Beijing, China
15 shared publications - Meicheng Liu
Tianjin University
14 shared publications - Shixuan Wang
Tianjin University
14 shared publications - Xihui Teng
Tianjin University
12 shared publications - Zhijun Zhang
Department of Electronic Engineering, Tsinghua University, Beijing, China
10 shared publications
Latest Publications
- 1 November 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 36 (11) , 1773-1776
Single-Port Reflection-Type Amplitude-Phase Modulator With Simultaneously and Independently Tunable Full-Range Amplitude and 360° Phase
This letter proposes a design method for the single-port reflection-type amplitude-phase modulator with simultaneously and independently tunable full-range amplitude and $360^{\boldsymbol {\circ }}$ phase. First, the principle of single-port amplitude-phase tuning is analyzed mathematically. The independent amplitude and phase tuning paths are selected and utilized to reconstruct the impedance distribution on the amplitude-phase plane. Second, based on the reconstruction concept, two topologies of single-port reflection-type amplitude-phase modulators are proposed to control the amplitude path and phase path simultaneously and independently, covering the reconstructed theoretical impedance distribution. The topologies consist of one 3-dB coupler and three tunable devices, exhibiting simplicity and high integration. Then, the enhanced hybrid integrated suspended line (eHISL) technology is employed in this design to reduce the insertion loss and further expand the amplitude tuning range. To verify the design strategy, two proof-of-concept amplitude-phase modulators were fabricated and measured. The first topology achieves a phase shift range of $383^{\boldsymbol {\circ }}$ and an amplitude modulation range of from −1.4 to −33.1 dB at 2.45 GHz. The second topology exhibits a phase shift range of $381^{\boldsymbol {\circ }}$ and an amplitude modulation range of from −2.8 to −19.6 dB at 2.45 GHz.
- 1 November 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 36 (11) , 1773-1776
Single-Port Reflection-Type Amplitude-Phase Modulator With Simultaneously and Independently Tunable Full-Range Amplitude and 360° Phase
This letter proposes a design method for the single-port reflection-type amplitude-phase modulator with simultaneously and independently tunable full-range amplitude and $360^{\boldsymbol {\circ }}$ phase. First, the principle of single-port amplitude-phase tuning is analyzed mathematically. The independent amplitude and phase tuning paths are selected and utilized to reconstruct the impedance distribution on the amplitude-phase plane. Second, based on the reconstruction concept, two topologies of single-port reflection-type amplitude-phase modulators are proposed to control the amplitude path and phase path simultaneously and independently, covering the reconstructed theoretical impedance distribution. The topologies consist of one 3-dB coupler and three tunable devices, exhibiting simplicity and high integration. Then, the enhanced hybrid integrated suspended line (eHISL) technology is employed in this design to reduce the insertion loss and further expand the amplitude tuning range. To verify the design strategy, two proof-of-concept amplitude-phase modulators were fabricated and measured. The first topology achieves a phase shift range of $383^{\boldsymbol {\circ }}$ and an amplitude modulation range of from −1.4 to −33.1 dB at 2.45 GHz. The second topology exhibits a phase shift range of $381^{\boldsymbol {\circ }}$ and an amplitude modulation range of from −2.8 to −19.6 dB at 2.45 GHz.
- 1 November 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 36 (11) , 1761-1764
A Novel Single-Port Phase Shifter With Low Loss and Full Phase Shift for Reconfigurable Reflectarray Based on HISL Technology
This letter proposes a novel single-port reflection-type phase shifter (SP-RTPS) based on the hybrid-integrated suspended line (HISL) technology. First, the topology and working principle of the SP-RTPS are proposed and analyzed theoretically. Unlike the conventional dual-port RTPS employing the branch-line/coupled-line coupler, the SP-RTPS comprises a rat-race coupler (RRC) with reflective loads to reflect the input signal back and output it at the same port with reconfigurable phase shift and invariant amplitude. Second, to miniaturize the size of conventional RRC, the SP-RTPS employs the $7\lambda $ /6-ring structure with open-stub loaded transmission lines (OSLTLs) to reduce the size by 65%. Finally, the SP-RTPS is designed, fabricated, and tested on the low-loss and self-packaged HISL technology at 2.45GHz. Measurement results show that the SP-RTPS provides a phase shift range (PSR) of 382° with a loss better than 1.47dB. Featuring full phase shift, high phase resolution, and low loss, the SP-RTPS is well-suited for reconfigurable reflectarrays (RRAs).
- 1 November 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 36 (11) , 1761-1764
A Novel Single-Port Phase Shifter With Low Loss and Full Phase Shift for Reconfigurable Reflectarray Based on HISL Technology
This letter proposes a novel single-port reflection-type phase shifter (SP-RTPS) based on the hybrid-integrated suspended line (HISL) technology. First, the topology and working principle of the SP-RTPS are proposed and analyzed theoretically. Unlike the conventional dual-port RTPS employing the branch-line/coupled-line coupler, the SP-RTPS comprises a rat-race coupler (RRC) with reflective loads to reflect the input signal back and output it at the same port with reconfigurable phase shift and invariant amplitude. Second, to miniaturize the size of conventional RRC, the SP-RTPS employs the $7\lambda $ /6-ring structure with open-stub loaded transmission lines (OSLTLs) to reduce the size by 65%. Finally, the SP-RTPS is designed, fabricated, and tested on the low-loss and self-packaged HISL technology at 2.45GHz. Measurement results show that the SP-RTPS provides a phase shift range (PSR) of 382° with a loss better than 1.47dB. Featuring full phase shift, high phase resolution, and low loss, the SP-RTPS is well-suited for reconfigurable reflectarrays (RRAs).
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 25 (10) , 4098-4102
A Design Method for a Dual-Band and Dual-Polarized Patch Antenna Based on a Single-Layer Dielectric Substrate for UAV Communication Applications
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 25 (10) , 4098-4102
A Design Method for a Dual-Band and Dual-Polarized Patch Antenna Based on a Single-Layer Dielectric Substrate for UAV Communication Applications
- 1 September 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 74 (9) , 9042-9047
A High-Gain Easy-Assembly All-Metal Endfire Antenna Based on a Quasi-2-D Aperture
- 1 September 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 74 (9) , 9042-9047
A High-Gain Easy-Assembly All-Metal Endfire Antenna Based on a Quasi-2-D Aperture
- 29 May 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. PP (15361225) , 1-5
A Vertically Polarized Narrow Width High Gain Meander-Line Bidirectional Array Antenna Mounted on Large-Scale Metal Plane
This letter proposes a vertically polarized meander line bidirectional array antenna with narrow width, accurate beam direction, high gain, and a high gain-to-area (G/A) ratio. First, to mitigate beam tilting observed in horizontally polarized antennas mounted on large-scale metal plane, a novel current distribution mode is proposed. This mode enables vertically polarization and a broadside bidirectional pattern without beam deviation. Moreover, the proposed mode inherently achieves a narrow width, facilitating practical deployment. Second, to simultaneously attain high gain and a high G/A ratio, an equivalent dipole array model is employed to guide structural optimization of meander-line antenna. Finally, a prototype is fabricated to validate the proposed design. Measurement results present bidirectional radiation with a narrow width of 0.15λ0, high gain of 10.53 dBi and a high G/A ratio of 13.92. Considering the above advantages, the proposed antenna shows promising potential for long and narrow scenarios.
- 29 May 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. PP (15361225) , 1-5
A Vertically Polarized Narrow Width High Gain Meander-Line Bidirectional Array Antenna Mounted on Large-Scale Metal Plane
This letter proposes a vertically polarized meander line bidirectional array antenna with narrow width, accurate beam direction, high gain, and a high gain-to-area (G/A) ratio. First, to mitigate beam tilting observed in horizontally polarized antennas mounted on large-scale metal plane, a novel current distribution mode is proposed. This mode enables vertically polarization and a broadside bidirectional pattern without beam deviation. Moreover, the proposed mode inherently achieves a narrow width, facilitating practical deployment. Second, to simultaneously attain high gain and a high G/A ratio, an equivalent dipole array model is employed to guide structural optimization of meander-line antenna. Finally, a prototype is fabricated to validate the proposed design. Measurement results present bidirectional radiation with a narrow width of 0.15λ0, high gain of 10.53 dBi and a high G/A ratio of 13.92. Considering the above advantages, the proposed antenna shows promising potential for long and narrow scenarios.
- 14 May 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. PP (2771957X) , 1-4
A Reconfigurable eHISL Phase Shifter With Transmission and Dual-Reflection Modes
This letter presents a novel reconfigurable phase shifter with transmission and dual-reflection modes based on enhanced hybrid integrated suspended line (eHISL) technology. The proposed phase shifter comprises a reconfigurable coupler with loads connected to its through and coupled ports. First, a novel reconfigurable phase shifter topology is proposed with detailed analysis, enabling electronic switching between transmission mode and dual-reflection mode. In dual-reflection mode, high isolation between the two ports enables independent control of their reflection phases. Second, to reduce insertion loss (IL), an air-dielectric-based eHISL structure is adopted in the design. Third, the parallel $L$ – $C$ dual-resonant loads are employed to achieve 7-bit 360° phase shift in both transmission and dual-reflection modes. Finally, the proposed phase shifter operating at 2.45 GHz is designed, fabricated, and measured. In transmission mode, it achieves a full phase shift range (PSR) with an IL of 1.42–2.20 dB. In dual-reflection mode, both the two ports achieve PSRs of 360° and return losses of 0.73–1.36 dB and 0.77–1.31dB, respectively, while maintaining an isolation better than 19dB between the two ports. The proposed reconfigurable phase shifter offers a solution for constructing full-coverage, high-gain, and high-precision reconfigurable intelligent surfaces (RISs).
- 14 May 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. PP (2771957X) , 1-4
A Reconfigurable eHISL Phase Shifter With Transmission and Dual-Reflection Modes
This letter presents a novel reconfigurable phase shifter with transmission and dual-reflection modes based on enhanced hybrid integrated suspended line (eHISL) technology. The proposed phase shifter comprises a reconfigurable coupler with loads connected to its through and coupled ports. First, a novel reconfigurable phase shifter topology is proposed with detailed analysis, enabling electronic switching between transmission mode and dual-reflection mode. In dual-reflection mode, high isolation between the two ports enables independent control of their reflection phases. Second, to reduce insertion loss (IL), an air-dielectric-based eHISL structure is adopted in the design. Third, the parallel $L$ – $C$ dual-resonant loads are employed to achieve 7-bit 360° phase shift in both transmission and dual-reflection modes. Finally, the proposed phase shifter operating at 2.45 GHz is designed, fabricated, and measured. In transmission mode, it achieves a full phase shift range (PSR) with an IL of 1.42–2.20 dB. In dual-reflection mode, both the two ports achieve PSRs of 360° and return losses of 0.73–1.36 dB and 0.77–1.31dB, respectively, while maintaining an isolation better than 19dB between the two ports. The proposed reconfigurable phase shifter offers a solution for constructing full-coverage, high-gain, and high-precision reconfigurable intelligent surfaces (RISs).
- 29 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 74 (7) , 7124-7129
A Low-Loss and Highly Integrated Circularly Polarized Modular Phased Array Based on Enhanced-HISL Technology
This communication proposes a low-loss and highly integrated circularly polarized (CP) modular phased array based on enhanced hybrid integrated suspended line (eHISL) technology. Firstly, eHISL technology is proposed and applied to the phased array architecture for the first time. eHISL is a stripline structure with air as dielectric. Due to the low-loss and self-packaging characteristics of the eHISL technology, the feed circuit exhibits low insertion loss, which further improves the radiation efficiency of the array. Secondly, miniaturization techniques and structural multifunction of the metal layers are applied. The antenna is miniaturized by 90° bending, and the phase shifter is miniaturized using a T-shape equivalent transmission line design. Additionally, the metal layer serves multiple functions, acting simultaneously as the radiator, ground plane, and cavity walls. The CP phased array achieves co-planar integration of antennas and feed circuits with no vertical transitions, and consists of only two layers of metal and one layer of printed circuit board (PCB). Thirdly, to make the system expandable, a modular 2×2 CP subarray is designed. The subarray can be flexibly expanded to a scale of 2m×2n CP phased array through external power dividers. Fourthly, an improved iterative optimization algorithm for periodic unequal spacing arrays is proposed. The proposed algorithm achieves significant sidelobe level suppression at wide scanning angles while maintaining stable main lobe gain. Finally, a 4×4 CP phased array consisting of four 2×2 CP subarrays is simulated, fabricated, and measured to evaluate the performance. The proposed array achieves a -10 dB impedance bandwidth of 17.7% and a radiation efficiency of 58.9% at the center frequency of 3 GHz with a size of 2.04λ0×2.04λ0×0.26λ0.
- 29 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 74 (7) , 7124-7129
A Low-Loss and Highly Integrated Circularly Polarized Modular Phased Array Based on Enhanced-HISL Technology
This communication proposes a low-loss and highly integrated circularly polarized (CP) modular phased array based on enhanced hybrid integrated suspended line (eHISL) technology. Firstly, eHISL technology is proposed and applied to the phased array architecture for the first time. eHISL is a stripline structure with air as dielectric. Due to the low-loss and self-packaging characteristics of the eHISL technology, the feed circuit exhibits low insertion loss, which further improves the radiation efficiency of the array. Secondly, miniaturization techniques and structural multifunction of the metal layers are applied. The antenna is miniaturized by 90° bending, and the phase shifter is miniaturized using a T-shape equivalent transmission line design. Additionally, the metal layer serves multiple functions, acting simultaneously as the radiator, ground plane, and cavity walls. The CP phased array achieves co-planar integration of antennas and feed circuits with no vertical transitions, and consists of only two layers of metal and one layer of printed circuit board (PCB). Thirdly, to make the system expandable, a modular 2×2 CP subarray is designed. The subarray can be flexibly expanded to a scale of 2m×2n CP phased array through external power dividers. Fourthly, an improved iterative optimization algorithm for periodic unequal spacing arrays is proposed. The proposed algorithm achieves significant sidelobe level suppression at wide scanning angles while maintaining stable main lobe gain. Finally, a 4×4 CP phased array consisting of four 2×2 CP subarrays is simulated, fabricated, and measured to evaluate the performance. The proposed array achieves a -10 dB impedance bandwidth of 17.7% and a radiation efficiency of 58.9% at the center frequency of 3 GHz with a size of 2.04λ0×2.04λ0×0.26λ0.
- 23 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 25 (6) , 2576-2580
A Novel Subarray-Level Beamforming Method for Compact, High-Gain, and Enhanced Gain-Bandwidth Periodic Leaky-Wave Endfire Antenna
In this letter, a compact high-gain and enhanced gain-bandwidth periodic leaky-wave endfire antenna (PLWEA) is proposed. It features a compact structure, high gain, and ease of assembly. In addition, it exhibits an enhanced gain-bandwidth and a high gain-to-length ratio (G/L ratio). Firstly, a novel subarray-level beamforming method (SLBM) based on a multi-unit alternated structure is proposed for the first time. This approach can reduce the relative dielectric constant of the substrate by suppressing grating lobes of the higher-order harmonic. A low dielectric constant substrate ensures a stable phase constant, thereby improving the 3 dB gain bandwidth. Furthermore, the dual-degree-of-freedom design method (DDFM) is adopted to realize high gain and high G/L ratio which also enhances flexibility by designing the feedline and elements independently. Finally, to verify the proposed approach, a prototype fabricated on a substrate with an ϵr of 2.2 achieved a measured gain of 14.1 dBi, a G/L ratio of 6.0, and a 3 dB gain bandwidth of 13%.
- 23 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 25 (6) , 2576-2580
A Novel Subarray-Level Beamforming Method for Compact, High-Gain, and Enhanced Gain-Bandwidth Periodic Leaky-Wave Endfire Antenna
In this letter, a compact high-gain and enhanced gain-bandwidth periodic leaky-wave endfire antenna (PLWEA) is proposed. It features a compact structure, high gain, and ease of assembly. In addition, it exhibits an enhanced gain-bandwidth and a high gain-to-length ratio (G/L ratio). Firstly, a novel subarray-level beamforming method (SLBM) based on a multi-unit alternated structure is proposed for the first time. This approach can reduce the relative dielectric constant of the substrate by suppressing grating lobes of the higher-order harmonic. A low dielectric constant substrate ensures a stable phase constant, thereby improving the 3 dB gain bandwidth. Furthermore, the dual-degree-of-freedom design method (DDFM) is adopted to realize high gain and high G/L ratio which also enhances flexibility by designing the feedline and elements independently. Finally, to verify the proposed approach, a prototype fabricated on a substrate with an ϵr of 2.2 achieved a measured gain of 14.1 dBi, a G/L ratio of 6.0, and a 3 dB gain bandwidth of 13%.
- 10 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. PP (2771957X) , 1-4
A Reconfigurable Harmonic Tag/Receiver for the Bidirectional Harmonic Radar System at 110/220 GHz
Conventional frequency-modulated continuous-wave (FMCW) radars struggle to detect small radar cross section (RCS) target amid large RCS clutter, that degrades the signal-to-interference-plus-noise-ratio (SINR). Harmonic radar solves this problem through a nonlinear active tag that converts the fundamental signal into the harmonic response, thereby isolating the target from the linear background. For a swarm system requiring decentralized detection, we propose the bidirectional harmonic radar system with a reconfigurable harmonic tag/receiver. The harmonic tag/receiver integrated a frequency doubler and a subharmonic mixer in the same chip. This design enables harmonic tag/receiver mode switching, while the sub-THz operating frequency improves the range resolution. This reconfigurable harmonic tag/receiver was fabricated using a 28-nm-bulk CMOS process, occupying a chip area of $760\times 520$ $\mu $ m2. The power consumption is 29 mW in tag mode and 11 mW in receiver mode. Moreover, at a fundamental input power of −1 dBm, the tag achieves a maximum saturated output power of −3.5 dBm at 218 GHz, and a 3-dB bandwidth of 206–238GHz. The receiver shows a maximum conversion gain (CG) of 17.6 dB and a minimum noise figure (NF) of 12.6 dB. Radar measurement at 220 GHz demonstrates a range resolution of 6 mm in both tag and receiver modes at a distance of 1 m.
- 10 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. PP (2771957X) , 1-4
A Reconfigurable Harmonic Tag/Receiver for the Bidirectional Harmonic Radar System at 110/220 GHz
Conventional frequency-modulated continuous-wave (FMCW) radars struggle to detect small radar cross section (RCS) target amid large RCS clutter, that degrades the signal-to-interference-plus-noise-ratio (SINR). Harmonic radar solves this problem through a nonlinear active tag that converts the fundamental signal into the harmonic response, thereby isolating the target from the linear background. For a swarm system requiring decentralized detection, we propose the bidirectional harmonic radar system with a reconfigurable harmonic tag/receiver. The harmonic tag/receiver integrated a frequency doubler and a subharmonic mixer in the same chip. This design enables harmonic tag/receiver mode switching, while the sub-THz operating frequency improves the range resolution. This reconfigurable harmonic tag/receiver was fabricated using a 28-nm-bulk CMOS process, occupying a chip area of $760\times 520$ $\mu $ m2. The power consumption is 29 mW in tag mode and 11 mW in receiver mode. Moreover, at a fundamental input power of −1 dBm, the tag achieves a maximum saturated output power of −3.5 dBm at 218 GHz, and a 3-dB bandwidth of 206–238GHz. The receiver shows a maximum conversion gain (CG) of 17.6 dB and a minimum noise figure (NF) of 12.6 dB. Radar measurement at 220 GHz demonstrates a range resolution of 6 mm in both tag and receiver modes at a distance of 1 m.