Teruki Someya
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Teruki Someya has a total of 48 co-authors. Here are the top co-authors by number of shared publications:
- Kenichi Okada
Department of Electrical and Electronic Engineering, Institute of Science Tokyo, Tokyo, Japan
5 shared publications Atsushi Shirane
Tokyo Institute of Technology, Tokyo, Japan
3 shared publications- Jian Pang
Institute of Science Tokyo, Tokyo, Japan
3 shared publications Makoto Takamiya
University of Tokyo, Tokyo 153-8505, Japan
3 shared publicationsTakayasu Sakurai
University of Tokyo, Tokyo 153-8505, Japan
3 shared publications- A. K. M. Mahfuzul Islam
Department of Information and Communications Engineering, School of Engineering, Institute of Science Tokyo, Ookayama, Meguro-ku, Tokyo, Japan
2 shared publications
Latest Publications
- 16 November 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Solid-State Circuits Letters
- Vol. 5, 272-275
A 210 nW NPN-Based Temperature Sensor With an Inaccuracy of ±0.15 °C (3σ) From −15 °C to 85 °C Utilizing Dual-Mode Frontend
This paper describes an NPN-based temperature sensor that achieves a 1-point trimmed inaccuracy of ±0.15 ∘C (3σ) from –15 to 85 ∘C while dissipating only 210 nW. It uses a dual-mode front-end to roughly halve the power consumption of conventional front-ends. First, two NPNs are used to generate a well-defined PTAT bias current, then this current is sampled and applied to the same NPNs to generate well-defined PTAT and CTAT voltages. These voltages are then applied to a low power tracking Σ modulator-based ADC, which employs a digital filter to efficiently generate a multi-bit representation of temperature. A prototype fabricated in a 180-nm BCD process achieves 15 mK resolution in a 50 ms conversion time, which translates into a state-of-the-art resolution FoM of 2.3 pJK2.
- 16 November 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Solid-State Circuits Letters
- Vol. 5, 272-275
A 210 nW NPN-Based Temperature Sensor With an Inaccuracy of ±0.15 °C (3σ) From −15 °C to 85 °C Utilizing Dual-Mode Frontend
This paper describes an NPN-based temperature sensor that achieves a 1-point trimmed inaccuracy of ±0.15 ∘C (3σ) from –15 to 85 ∘C while dissipating only 210 nW. It uses a dual-mode front-end to roughly halve the power consumption of conventional front-ends. First, two NPNs are used to generate a well-defined PTAT bias current, then this current is sampled and applied to the same NPNs to generate well-defined PTAT and CTAT voltages. These voltages are then applied to a low power tracking Σ modulator-based ADC, which employs a digital filter to efficiently generate a multi-bit representation of temperature. A prototype fabricated in a 180-nm BCD process achieves 15 mK resolution in a 50 ms conversion time, which translates into a state-of-the-art resolution FoM of 2.3 pJK2.
- Open Access
- 26 July 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 57 (2) , 356-370
A Ka-Band SATCOM Transceiver in 65-nm CMOS With High-Linearity TX and Dual-Channel Wide-Dynamic-Range RX for Terrestrial Terminal
In this article, a $Ka$ -band satellite communication (SATCOM) transceiver is first presented using a standard CMOS technology. The proposed $Ka$ -band SATCOM transceiver consists of a high-linearity transmitter (TX) and dual-channel receiver (RX); both TX and RX are based on direct-conversion architecture. By implementing the dual-channel RX, multiple multiplexing modes, including polarization multiplexing and frequency multiplexing, can be enabled depending on the application. The RX variable gain is distributed in both RF blocks and baseband blocks to achieve a wide input dynamic range. The LNA employs a dual-coupling transformer for a low-noise figure (NF) and wideband input matching; moreover, it enhances the amplifier unilateralization characteristic to mitigate the loading effect from switched attenuators. An adjacent channel interference (ACI) cancellation scheme is proposed to further enhance the RX linearity in the frequency multiplexing mode. In the TX, single-turn high-quality-factor transformer is employed to realize matching network and four-way power combining. A prototype of the SATCOM transceiver is fabricated in a standard 65-nm CMOS process. Under 1.05-V supply voltage, the TX achieves a $P_{\mathrm {SAT}}$ of 20.5 dBm and an average output power of 12 dBm with 2% error vector magnitude (EVM) and a 37.6-dB ACPR. The dual-channel RX achieves an NF of 5.4 dB, an IIP3 of −30 dBm on the high-gain mode, the ACI cancellation is measured of 7.9 dB with a 100-MHz signal bandwidth.
- 26 July 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 57 (2) , 356-370
Open AccessA Ka-Band SATCOM Transceiver in 65-nm CMOS With High-Linearity TX and Dual-Channel Wide-Dynamic-Range RX for Terrestrial Terminal
In this article, a $Ka$ -band satellite communication (SATCOM) transceiver is first presented using a standard CMOS technology. The proposed $Ka$ -band SATCOM transceiver consists of a high-linearity transmitter (TX) and dual-channel receiver (RX); both TX and RX are based on direct-conversion architecture. By implementing the dual-channel RX, multiple multiplexing modes, including polarization multiplexing and frequency multiplexing, can be enabled depending on the application. The RX variable gain is distributed in both RF blocks and baseband blocks to achieve a wide input dynamic range. The LNA employs a dual-coupling transformer for a low-noise figure (NF) and wideband input matching; moreover, it enhances the amplifier unilateralization characteristic to mitigate the loading effect from switched attenuators. An adjacent channel interference (ACI) cancellation scheme is proposed to further enhance the RX linearity in the frequency multiplexing mode. In the TX, single-turn high-quality-factor transformer is employed to realize matching network and four-way power combining. A prototype of the SATCOM transceiver is fabricated in a standard 65-nm CMOS process. Under 1.05-V supply voltage, the TX achieves a $P_{\mathrm {SAT}}$ of 20.5 dBm and an average output power of 12 dBm with 2% error vector magnitude (EVM) and a 37.6-dB ACPR. The dual-channel RX achieves an NF of 5.4 dB, an IIP3 of −30 dBm on the high-gain mode, the ACI cancellation is measured of 7.9 dB with a 100-MHz signal bandwidth.
- Open Access
- 12 November 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 68 (2) , 603-616
A Fully Synthesizable Fractional-N MDLL With Zero-Order Interpolation-Based DTC Nonlinearity Calibration and Two-Step Hybrid Phase Offset Calibration
In this paper, a fully-synthesizable digital-to-time (DTC)-based fractional-Nmultiplying delay-locked loop(MDLL) is presented. Noise and linearity of synthesizable DTCs are analyzed, and a two-stage synthesizable DTC is proposed in which a path-selection DTC is used as the coarse stage and a variable-slope DTC is used as the fine stage. To calibrate the DTC nonlinearity, a highly robust zero-order interpolation based nonlinearity calibration is proposed. Besides, the static phase offsets (SPO) between bang-bang phase detector (BBPD) and multiplexer (MUX) are calibrated by a proposed hybrid analog/digital phase offset calibration, while the dynamic phase offsets (DPO) are removed by a proposed complementary switching scheme. The co-design of the analog circuits and digital calibrations enable excellent jitter and spur performance. The MDLL achieves 0.70 and 0.48ps root-mean-square (RMS) jitter in fractional-N and integer-N modes, respectively. The fractional spur is less than -59.0dBc, and the reference spur is -64.5dBc. The power consumptions are 1.85mW and 1.22mW, corresponding to figures of merit (FOM) of -240.4dB and -245.5dB.
- 12 November 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 68 (2) , 603-616
Open AccessA Fully Synthesizable Fractional-N MDLL With Zero-Order Interpolation-Based DTC Nonlinearity Calibration and Two-Step Hybrid Phase Offset Calibration
In this paper, a fully-synthesizable digital-to-time (DTC)-based fractional-Nmultiplying delay-locked loop(MDLL) is presented. Noise and linearity of synthesizable DTCs are analyzed, and a two-stage synthesizable DTC is proposed in which a path-selection DTC is used as the coarse stage and a variable-slope DTC is used as the fine stage. To calibrate the DTC nonlinearity, a highly robust zero-order interpolation based nonlinearity calibration is proposed. Besides, the static phase offsets (SPO) between bang-bang phase detector (BBPD) and multiplexer (MUX) are calibrated by a proposed hybrid analog/digital phase offset calibration, while the dynamic phase offsets (DPO) are removed by a proposed complementary switching scheme. The co-design of the analog circuits and digital calibrations enable excellent jitter and spur performance. The MDLL achieves 0.70 and 0.48ps root-mean-square (RMS) jitter in fractional-N and integer-N modes, respectively. The fractional spur is less than -59.0dBc, and the reference spur is -64.5dBc. The power consumptions are 1.85mW and 1.22mW, corresponding to figures of merit (FOM) of -240.4dB and -245.5dB.
- 22 September 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Solid-State Circuits Letters
- Vol. 3, 458-461
A 6.4 nW 1.7% Relative Inaccuracy CMOS Temperature Sensor Utilizing Sub-Thermal Drain Voltage Stabilization and Frequency-Locked Loop
A 6.4 nW 1.7 % relative inaccuracy (R-IA) CMOS sub-thermal drain voltage-based temperature sensor is proposed. The proposed stabilized sub-thermal drain voltage current generator achieves a highly linear PTAT output without nonlinearity fitting or post-fabrication trimming, and increases the accuracy of the sensor. A combination of the current generator and a frequency-locked-loop relaxes the tradeoff between power and temperature stability of the current-to-frequency converter, and achieves supply-voltage-independent operation. Measured results of the prototype fabricated in a 65 nm CMOS process show that the proposed temperature sensor has a -1.0/+0.7 ∘C inaccuracy (= R-IA of 1.7 %) while achieving a resolution of 75 mK over a temperature range of -30 to 70 ∘C. The line sensitivity of the sensor is 2.8 ∘C/V.
- 22 September 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Solid-State Circuits Letters
- Vol. 3, 458-461
A 6.4 nW 1.7% Relative Inaccuracy CMOS Temperature Sensor Utilizing Sub-Thermal Drain Voltage Stabilization and Frequency-Locked Loop
A 6.4 nW 1.7 % relative inaccuracy (R-IA) CMOS sub-thermal drain voltage-based temperature sensor is proposed. The proposed stabilized sub-thermal drain voltage current generator achieves a highly linear PTAT output without nonlinearity fitting or post-fabrication trimming, and increases the accuracy of the sensor. A combination of the current generator and a frequency-locked-loop relaxes the tradeoff between power and temperature stability of the current-to-frequency converter, and achieves supply-voltage-independent operation. Measured results of the prototype fabricated in a 65 nm CMOS process show that the proposed temperature sensor has a -1.0/+0.7 ∘C inaccuracy (= R-IA of 1.7 %) while achieving a resolution of 75 mK over a temperature range of -30 to 70 ∘C. The line sensitivity of the sensor is 2.8 ∘C/V.
- 1 November 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 267-270
An IoT Sensor Node SoC with Dynamic Power Scheduling for Sustainable Operation in Energy Harvesting Environment
This paper describes a low-power IoT sensor node SoC that can be used for factory automation and wearable healthcare applications. It features dynamic power scheduling method suitable for the environment that works with an energy harvester. Our proposed SoC architecture is composed of a low power (60 nA) RTC, a normally-off RF which has fast start-up time (0.5 µs), and other low-power components. A mixed-signal SoC has been fabricated using the TSMC 65 nm LP process. The sensor node system equipped with dynamic power scheduling consumes about 3.4 µW when the activity ratio is 0.1%. Evaluation results show that the proposed method can reduce about 51% of the power consumption compared with the case without dynamic power scheduling in sensor node SoC. Also, the parameters of the system in energy harvesting environment can be adjusted under the trade-off with power consumption and measurement accuracy according to the application requirements.
- 1 November 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 267-270
An IoT Sensor Node SoC with Dynamic Power Scheduling for Sustainable Operation in Energy Harvesting Environment
This paper describes a low-power IoT sensor node SoC that can be used for factory automation and wearable healthcare applications. It features dynamic power scheduling method suitable for the environment that works with an energy harvester. Our proposed SoC architecture is composed of a low power (60 nA) RTC, a normally-off RF which has fast start-up time (0.5 µs), and other low-power components. A mixed-signal SoC has been fabricated using the TSMC 65 nm LP process. The sensor node system equipped with dynamic power scheduling consumes about 3.4 µW when the activity ratio is 0.1%. Evaluation results show that the proposed method can reduce about 51% of the power consumption compared with the case without dynamic power scheduling in sensor node SoC. Also, the parameters of the system in energy harvesting environment can be adjusted under the trade-off with power consumption and measurement accuracy according to the application requirements.
- Open Access
- 12 September 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 54 (12) , 3478-3492
A 265-$\mu$ W Fractional-${N}$ Digital PLL With Seamless Automatic Switching Sub-Sampling/Sampling Feedback Path and Duty-Cycled Frequency-Locked Loop in 65-nm CMOS
This article proposes a fractional-N digital phase-locked loop (DPLL) that achieves a 265-μW ultra-low-power operation. The proposed switching feedback can seamlessly change the DPLL from sampling operation to sub-sampling operation without disturbing the phase-locked state of the DPLL to reduce the number of building blocks that works at the oscillator frequency, leading to significant power reduction. With the reduced number of high-frequency circuits, scaling the reference frequency is fully used to reduce the power consumption of the DPLL. Together with an out-of-dead-zone detector and a duty-cycled frequency-locked loop running in the background, the switching feedback achieves robust frequency and phase acquisition at start-up and helps the sub-sampling PLL recover when large phase and frequency disturbances occur. A transformer-based stacked-gm oscillator is proposed to minimize the power consumption while providing the sufficient swing to drive the subsequent stages. A truncated constant-slope digital-to-time converter is proposed to improve the power efficiency while retaining good linearity. The proposed fractional-N DPLL consumes only 265 μW while achieving an integrated jitter of 2.8 ps and a worst case fractional spur of -52 dBc, which corresponds to a figure of merit (FOM) of -237 dB.
- 12 September 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 54 (12) , 3478-3492
Open AccessA 265-$\mu$ W Fractional-${N}$ Digital PLL With Seamless Automatic Switching Sub-Sampling/Sampling Feedback Path and Duty-Cycled Frequency-Locked Loop in 65-nm CMOS
This article proposes a fractional-N digital phase-locked loop (DPLL) that achieves a 265-μW ultra-low-power operation. The proposed switching feedback can seamlessly change the DPLL from sampling operation to sub-sampling operation without disturbing the phase-locked state of the DPLL to reduce the number of building blocks that works at the oscillator frequency, leading to significant power reduction. With the reduced number of high-frequency circuits, scaling the reference frequency is fully used to reduce the power consumption of the DPLL. Together with an out-of-dead-zone detector and a duty-cycled frequency-locked loop running in the background, the switching feedback achieves robust frequency and phase acquisition at start-up and helps the sub-sampling PLL recover when large phase and frequency disturbances occur. A transformer-based stacked-gm oscillator is proposed to minimize the power consumption while providing the sufficient swing to drive the subsequent stages. A truncated constant-slope digital-to-time converter is proposed to improve the power efficiency while retaining good linearity. The proposed fractional-N DPLL consumes only 265 μW while achieving an integrated jitter of 2.8 ps and a worst case fractional spur of -52 dBc, which corresponds to a figure of merit (FOM) of -237 dB.
- 29 January 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 54 (3) , 613-622
An 11-nW CMOS Temperature-to-Digital Converter Utilizing Sub-Threshold Current at Sub-Thermal Drain Voltage
A fully integrated CMOS temperature-to-digital converter utilizing MOSFETs in the sub-threshold region is proposed. The temperature-to-digital converter achieves the ultra-low power operation required for Internet of Things (IoT) nodes. The proposed principle takes the ratio of the sub-threshold currents of two nMOSFETs whose drain voltages are maintained well above and well below the thermal voltage, respectively. The proposed circuit implementation of the temperature-to-digital converter achieves ultra-low power consumption of 11 nW at room temperature of 25 °C. Measurement results of the proposed temperature sensor fabricated in a 180-nm CMOS process show -0.9/+1.2 °C peak-to-peak inaccuracy over a temperature range of -20 °C to 80 °C after a two-point calibration while achieving a resolution of 145 mK.
- 29 January 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 54 (3) , 613-622
An 11-nW CMOS Temperature-to-Digital Converter Utilizing Sub-Threshold Current at Sub-Thermal Drain Voltage
A fully integrated CMOS temperature-to-digital converter utilizing MOSFETs in the sub-threshold region is proposed. The temperature-to-digital converter achieves the ultra-low power operation required for Internet of Things (IoT) nodes. The proposed principle takes the ratio of the sub-threshold currents of two nMOSFETs whose drain voltages are maintained well above and well below the thermal voltage, respectively. The proposed circuit implementation of the temperature-to-digital converter achieves ultra-low power consumption of 11 nW at room temperature of 25 °C. Measurement results of the proposed temperature sensor fabricated in a 180-nm CMOS process show -0.9/+1.2 °C peak-to-peak inaccuracy over a temperature range of -20 °C to 80 °C after a two-point calibration while achieving a resolution of 145 mK.
- 28 November 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 66 (3) , 1270-1279
A 0.90–4.39-V Detection Voltage Range, 56-Level Programmable Voltage Detector Using Fine Voltage-Step Subtraction for Battery Management
- 28 November 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 66 (3) , 1270-1279
A 0.90–4.39-V Detection Voltage Range, 56-Level Programmable Voltage Detector Using Fine Voltage-Step Subtraction for Battery Management
- 1 January 2017
- Published by Institute of Electronics, Information and Communications Engineers (IEICE) in IEICE Transactions on Electronics
- Vol. E100.C (4) , 349-358
Design and Analysis of Ultra-Low Power Glitch-Free Programmable Voltage Detector Based on Multiple Voltage Copier
- 1 January 2017
- Published by Institute of Electronics, Information and Communications Engineers (IEICE) in IEICE Transactions on Electronics
- Vol. E100.C (4) , 349-358
Design and Analysis of Ultra-Low Power Glitch-Free Programmable Voltage Detector Based on Multiple Voltage Copier