Yu-Ching Hsiao
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Yu-Ching Hsiao has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Jing-Jing Fang
Department of Mechanical Engineering, National Cheng Kung University, Tainan, Taiwan
9 shared publications - Chih-Ju Chang
Cathay General Hospital
2 shared publications Chen-Jung Chang
Division of Orthodontics, Department of Stomatology, National Cheng Kung University Hospital, No.138,Sheng Li Road, Tainan, Tainan, 70403, TAIWAN
1 shared publication- Chen-Jung Chang
Division of Orthodontics, Department of Stomatology, National Cheng Kung University Hospital, College of Medicine, National Cheng Kung University, Tainan 704, Taiwan
1 shared publication - Cheng-Li Lin
Department of Orthopedic Surgery, National Cheng Kung University Hospital, College of Medicine, National Cheng Kung University, Tainan, Taiwan
1 shared publication Chih-Ta Huang
Division of Neurosurgery, Department of Surgery, Cathay General Hospital, Taipei City, Taiwan
1 shared publication
Latest Publications
- Open Access
- 22 April 2026
- Published by IOP Publishing in Medical Engineering & Physics
- Vol. 147 (5) , 055006
Immobilization and comfort assessment in customized 3D-printed cervical orthosis
Customized 3D-printed cervical orthoses usually offer better fit and support. However, clinical evidence regarding the effectiveness of immobilization and comfort remains limited. This study aims to compare the effectiveness of custom-made cervical orthoses with that of commercially available orthoses in preventing pressure ulcers (PUs), improving immobilization, and providing comfort and ease of use. We measured the risk of PUs associated with six neck postures to assess comfort and immobilization when participants wore their orthosis. The customized cervical orthosis provided significantly greater immobilization than the Aspen Vista collar across all six neck postures (p < 0.05). No significant differences in comfort and user preference were observed between the two orthoses. The customized cervical orthosis offers superior immobilization compared to the Aspen Vista collar; however, it may increase pressure on the mastoid processes. While comfort is comparable to commercial options, customized orthosis improvements are needed to reduce pressure without sacrificing immobilization.
- 22 April 2026
- Published by IOP Publishing in Medical Engineering & Physics
- Vol. 147 (5) , 055006
Open AccessImmobilization and comfort assessment in customized 3D-printed cervical orthosis
Customized 3D-printed cervical orthoses usually offer better fit and support. However, clinical evidence regarding the effectiveness of immobilization and comfort remains limited. This study aims to compare the effectiveness of custom-made cervical orthoses with that of commercially available orthoses in preventing pressure ulcers (PUs), improving immobilization, and providing comfort and ease of use. We measured the risk of PUs associated with six neck postures to assess comfort and immobilization when participants wore their orthosis. The customized cervical orthosis provided significantly greater immobilization than the Aspen Vista collar across all six neck postures (p < 0.05). No significant differences in comfort and user preference were observed between the two orthoses. The customized cervical orthosis offers superior immobilization compared to the Aspen Vista collar; however, it may increase pressure on the mastoid processes. While comfort is comparable to commercial options, customized orthosis improvements are needed to reduce pressure without sacrificing immobilization.
- Open Access
- 22 January 2026
- Published by Springer Nature in Neurosurgical Review
- Vol. 49 (1) , 143
A novel bone screw implantation strategy in C1-2 instability: a framework for evolving high cervical spine surgery
Fixation surgery for atlantoaxial instability (AAI) or atlantoaxial subluxation is recognized as a complex and high-risk procedure, prompting the development of various fixation techniques. In this preliminary study, we evaluated the safety and accuracy of C1-2 pedicle screw insertion using our developed planning software and 3D-printed guiding templates. We also analyzed feasibility with free-hand techniques to identify an optimal strategy for atlantoaxial fixation. We used a self-developed 3D planning method, along with guiding template techniques, for pedicle screws in high cervical vertebra fixation. A small cohort of thirteen patients in Group 1 received free-hand screw placement, while seventeen in Group 2 performed using the planning and guiding system. We analyzed demographics, complications, and screw placement precision. We compared the demographics, operative time, and blood loss between the two groups. Complications occurred in patients from Group 1, but none in those from Group 2. Most Group 2 patients underwent the C1 and C2 pedicle screws approach, which showed significantly higher screw placement safety. Both pedicle screws applied in C1 and C2 are preferable to occipitocervical fusion when feasible. The planning strategy and its associated guiding system improve the implanted screws precision and safety of pedicle screw placement, particularly in cases with high-riding vertebral arteries. When the C2 pedicle diameter exceeds 3 mm, we safely perform the C2 pedicle screws. This method supports more precise preoperative planning for atlantoaxial instability.
- 22 January 2026
- Published by Springer Nature in Neurosurgical Review
- Vol. 49 (1) , 143
Open AccessA novel bone screw implantation strategy in C1-2 instability: a framework for evolving high cervical spine surgery
Fixation surgery for atlantoaxial instability (AAI) or atlantoaxial subluxation is recognized as a complex and high-risk procedure, prompting the development of various fixation techniques. In this preliminary study, we evaluated the safety and accuracy of C1-2 pedicle screw insertion using our developed planning software and 3D-printed guiding templates. We also analyzed feasibility with free-hand techniques to identify an optimal strategy for atlantoaxial fixation. We used a self-developed 3D planning method, along with guiding template techniques, for pedicle screws in high cervical vertebra fixation. A small cohort of thirteen patients in Group 1 received free-hand screw placement, while seventeen in Group 2 performed using the planning and guiding system. We analyzed demographics, complications, and screw placement precision. We compared the demographics, operative time, and blood loss between the two groups. Complications occurred in patients from Group 1, but none in those from Group 2. Most Group 2 patients underwent the C1 and C2 pedicle screws approach, which showed significantly higher screw placement safety. Both pedicle screws applied in C1 and C2 are preferable to occipitocervical fusion when feasible. The planning strategy and its associated guiding system improve the implanted screws precision and safety of pedicle screw placement, particularly in cases with high-riding vertebral arteries. When the C2 pedicle diameter exceeds 3 mm, we safely perform the C2 pedicle screws. This method supports more precise preoperative planning for atlantoaxial instability.
- Open Access
- 19 March 2025
- Published by IOP Publishing in Biomedical Physics & Engineering Express
- Vol. 11 (3) , 037001
A facebow-free technique for mechanical articulator remounting using computed tomography
This technical note introduces a technique for remounting dental casts to a mechanical articulator using computed tomography (CT) without a facebow. We have developed a jig method that ensures precise remounting by aligning the virtual dental casts to the upper and lower jaw models reconstructed from the CT and transferring them to a virtual articulator based on anatomical landmarks. A custom-designed positioning jig and splint further enhance the accuracy of the process, preserving the spatial relationship between the midface and mandible. The proposed mounting jig technique can help transfer the patient’s maxillomandibular relationship quickly, repeatedly, and accurately to an articulator after the patient leaves.
- 19 March 2025
- Published by IOP Publishing in Biomedical Physics & Engineering Express
- Vol. 11 (3) , 037001
Open AccessA facebow-free technique for mechanical articulator remounting using computed tomography
This technical note introduces a technique for remounting dental casts to a mechanical articulator using computed tomography (CT) without a facebow. We have developed a jig method that ensures precise remounting by aligning the virtual dental casts to the upper and lower jaw models reconstructed from the CT and transferring them to a virtual articulator based on anatomical landmarks. A custom-designed positioning jig and splint further enhance the accuracy of the process, preserving the spatial relationship between the midface and mandible. The proposed mounting jig technique can help transfer the patient’s maxillomandibular relationship quickly, repeatedly, and accurately to an articulator after the patient leaves.
- Open Access
- 22 August 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (16) , 7424
Anatomical-Based Customized Cervical Orthosis Design in Automation
Cervical orthoses, vital for neck immobilization in medical care and sports, often struggle to provide adequate support due to individual neck shape and size variations. This study addresses this issue by developing a specific computer-aided orthosis design software tailored for creating customized 3D-printed cervical orthoses. The self-developed software embedded anatomical and rehabilitation knowledge into the orthosis design process, ensuring consistency and reducing manual modification. Finite element analysis of cervical orthoses determined that a minimum thickness of 5 mm PLA (polylactic acid) material is necessary to meet safety requirements. This study highlights the automation potential of customized computer-aided orthosis design and underscores the potential to revolutionize orthopedic care. We also applied easy-to-access 3D printing technology to fabricate well-fitting and immobilized cervical orthoses. These customized cervical orthoses offer a promising future with the advantages of being cost-effective, lightweight, immobility, comfortable, easy to wear, and minimal accessories to meet clinical needs, enhancing patient comfort and compliance and providing reassurance about the economic benefits of the technology.
- 22 August 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (16) , 7424
Open AccessAnatomical-Based Customized Cervical Orthosis Design in Automation
Cervical orthoses, vital for neck immobilization in medical care and sports, often struggle to provide adequate support due to individual neck shape and size variations. This study addresses this issue by developing a specific computer-aided orthosis design software tailored for creating customized 3D-printed cervical orthoses. The self-developed software embedded anatomical and rehabilitation knowledge into the orthosis design process, ensuring consistency and reducing manual modification. Finite element analysis of cervical orthoses determined that a minimum thickness of 5 mm PLA (polylactic acid) material is necessary to meet safety requirements. This study highlights the automation potential of customized computer-aided orthosis design and underscores the potential to revolutionize orthopedic care. We also applied easy-to-access 3D printing technology to fabricate well-fitting and immobilized cervical orthoses. These customized cervical orthoses offer a promising future with the advantages of being cost-effective, lightweight, immobility, comfortable, easy to wear, and minimal accessories to meet clinical needs, enhancing patient comfort and compliance and providing reassurance about the economic benefits of the technology.
- 23 May 2024
- Published by Elsevier in World Neurosurgery
- Vol. 188, e357-e366
A Three-Dimensional Morphological Assessment for Evaluating Pre- and Postsurgery in Cervical Laminoplasty
- 23 May 2024
- Published by Elsevier in World Neurosurgery
- Vol. 188, e357-e366
A Three-Dimensional Morphological Assessment for Evaluating Pre- and Postsurgery in Cervical Laminoplasty
- Open Access
- 6 March 2023
- Published by MDPI AG in Bioengineering
- Vol. 10 (3) , 335
A Symmetry-Based Superposition Method for Planning and Surgical Outcome Assessment
Computer-aided surgical planning has been widely used to increase the safety and predictability of surgery. The validation of the target of surgical planning to surgical outcomes on a patient-specific model is an important issue. The aim of this research was to develop a robust superposition method to assess the deviation of planning and outcome by using the symmetrical characteristic of the affected target. The optimal symmetry plane (OSP) of an object is usually used to evaluate the degree of symmetry of an object. We proposed a refined OSP-based contouring method to transfer a complex three-dimensional superposition operation into two dimensions. We compared the typical iterative closest point (ICP) algorithm with the refined OSP-based contouring method and examined the differences between them. The results using the OSP-based method were much better than the traditional method. As for processing time, the OSP-based contouring method was 11 times faster than the ICP method overall. The proposed method was not affected by the metallic artifacts from medical imaging or geometric changes due to surgical intervention. This technique can be applied for post-operative assessment, such as quantifying the differences between surgical targets and outcomes as well as performing long-term medical follow-up.
- 6 March 2023
- Published by MDPI AG in Bioengineering
- Vol. 10 (3) , 335
Open AccessA Symmetry-Based Superposition Method for Planning and Surgical Outcome Assessment
Computer-aided surgical planning has been widely used to increase the safety and predictability of surgery. The validation of the target of surgical planning to surgical outcomes on a patient-specific model is an important issue. The aim of this research was to develop a robust superposition method to assess the deviation of planning and outcome by using the symmetrical characteristic of the affected target. The optimal symmetry plane (OSP) of an object is usually used to evaluate the degree of symmetry of an object. We proposed a refined OSP-based contouring method to transfer a complex three-dimensional superposition operation into two dimensions. We compared the typical iterative closest point (ICP) algorithm with the refined OSP-based contouring method and examined the differences between them. The results using the OSP-based method were much better than the traditional method. As for processing time, the OSP-based contouring method was 11 times faster than the ICP method overall. The proposed method was not affected by the metallic artifacts from medical imaging or geometric changes due to surgical intervention. This technique can be applied for post-operative assessment, such as quantifying the differences between surgical targets and outcomes as well as performing long-term medical follow-up.
- Open Access
- 26 September 2022
- Published by MDPI AG in Journal of Clinical Medicine
- Vol. 11 (19) , 5689
An Automatic Voxel-Based Method for Optimal Symmetry Plane Generation for the Maxillofacial Region in Severe Asymmetry Cases
Symmetry is representative of aesthetics and health in all kinds of vertebrates, especially the human face. Therefore, to automatically locate the appropriate symmetry plane is crucial. The aim of this study was to develop an automatic and reliable method to determine the symmetry plane of the maxillofacial region. We compared the proposed method of determining the symmetry plane by assessing landmark-based and surface-based methods by way of quantitative symmetry assessments. Statistical analysis was applied to evaluate whether significant difference existed among these three kinds of symmetry planes. Twenty cases who had a diagnosis of severe facial asymmetry were evaluated retrospectively. The results showed that searching for the symmetry plane using a voxel-based method, named the optimal symmetry plane (OSP), achieved the most representative symmetry according to the outcomes of the trials. The OSP was significantly more symmetrical than the other two planes, as determined by other methods. The paired-voxel computation method proposed in this research is a robust and reliable method for identifying the unique symmetry plane for patients with severe facial asymmetry. Symmetry is of crucial significance for all kinds of vertebrates, including its clinical implications for surgical planning in orthognathic surgery.
- 26 September 2022
- Published by MDPI AG in Journal of Clinical Medicine
- Vol. 11 (19) , 5689
Open AccessAn Automatic Voxel-Based Method for Optimal Symmetry Plane Generation for the Maxillofacial Region in Severe Asymmetry Cases
Symmetry is representative of aesthetics and health in all kinds of vertebrates, especially the human face. Therefore, to automatically locate the appropriate symmetry plane is crucial. The aim of this study was to develop an automatic and reliable method to determine the symmetry plane of the maxillofacial region. We compared the proposed method of determining the symmetry plane by assessing landmark-based and surface-based methods by way of quantitative symmetry assessments. Statistical analysis was applied to evaluate whether significant difference existed among these three kinds of symmetry planes. Twenty cases who had a diagnosis of severe facial asymmetry were evaluated retrospectively. The results showed that searching for the symmetry plane using a voxel-based method, named the optimal symmetry plane (OSP), achieved the most representative symmetry according to the outcomes of the trials. The OSP was significantly more symmetrical than the other two planes, as determined by other methods. The paired-voxel computation method proposed in this research is a robust and reliable method for identifying the unique symmetry plane for patients with severe facial asymmetry. Symmetry is of crucial significance for all kinds of vertebrates, including its clinical implications for surgical planning in orthognathic surgery.
- Open Access
Quantitative Asymmetry Assessment between Virtual and Mixed Reality Planning for Orthognathic Surgery—A Retrospective Study
Orthognathic surgical planning compromises three clinical needs: occlusal balancing, symmetry, and harmony, which may result in multiple outcomes. Facial symmetry is the ultimate goal for patients and practitioners. Pure virtual planning and mixed reality planning were two innovative technologies in clinical practices compared to conventional model surgery used for decades. We proposed quantitative asymmetry assessment methods in both mandibular contour (in 2D) and a midface and mandible relationship in 3D. A computerized optimal symmetry plane, being the median plane, was applied in both planning methods. In the 3D asymmetry assessment between two planning methods, the deviation angle and deviation distance between midface and mandible were within 2° and 1.5 mm, respectively. There was no significant difference, except the symmetry index of the anterior deviation angle between the virtual and mixed reality planning in the 3D asymmetry assessment. In the mandible contour assessment, there was no significant difference between the virtual and mixed reality planning in asymmetry assessment in the frontal and frontal downward inclined views. Quantitative outcomes in 3D asymmetry indices showed that mixed reality planning was slightly more symmetric than virtual planning, with the opposite in 2D contouring.
Open AccessQuantitative Asymmetry Assessment between Virtual and Mixed Reality Planning for Orthognathic Surgery—A Retrospective Study
Orthognathic surgical planning compromises three clinical needs: occlusal balancing, symmetry, and harmony, which may result in multiple outcomes. Facial symmetry is the ultimate goal for patients and practitioners. Pure virtual planning and mixed reality planning were two innovative technologies in clinical practices compared to conventional model surgery used for decades. We proposed quantitative asymmetry assessment methods in both mandibular contour (in 2D) and a midface and mandible relationship in 3D. A computerized optimal symmetry plane, being the median plane, was applied in both planning methods. In the 3D asymmetry assessment between two planning methods, the deviation angle and deviation distance between midface and mandible were within 2° and 1.5 mm, respectively. There was no significant difference, except the symmetry index of the anterior deviation angle between the virtual and mixed reality planning in the 3D asymmetry assessment. In the mandible contour assessment, there was no significant difference between the virtual and mixed reality planning in asymmetry assessment in the frontal and frontal downward inclined views. Quantitative outcomes in 3D asymmetry indices showed that mixed reality planning was slightly more symmetric than virtual planning, with the opposite in 2D contouring.
- 28 November 2018
- Published by U-turn Press LLC in Computer-Aided Design and Applications
- Vol. 16 (4)
A Novel Design of an Expandable Cage used in Posterior Interbody Fusion for Lumbar Spine Surgery
Computer-Aided Design and Applications is an international journal on the applications of CAD and CAM. It publishes papers in the general domain of CAD plus in emerging fields like bio-CAD, nano-CAD, soft-CAD, garment-CAD, PLM, PDM, CAD data mining, CAD and the internet, CAD education, genetic algorithms and CAD engines. The journal is aimed at all developers and users of CAD technology to ptovide CAD solutions for various stages of design and manufacturing. The journal publishes all about Computer-Aided Design and Computer-Aided technologies.
- 28 November 2018
- Published by U-turn Press LLC in Computer-Aided Design and Applications
- Vol. 16 (4)
A Novel Design of an Expandable Cage used in Posterior Interbody Fusion for Lumbar Spine Surgery
Computer-Aided Design and Applications is an international journal on the applications of CAD and CAM. It publishes papers in the general domain of CAD plus in emerging fields like bio-CAD, nano-CAD, soft-CAD, garment-CAD, PLM, PDM, CAD data mining, CAD and the internet, CAD education, genetic algorithms and CAD engines. The journal is aimed at all developers and users of CAD technology to ptovide CAD solutions for various stages of design and manufacturing. The journal publishes all about Computer-Aided Design and Computer-Aided technologies.