Jiankun Liu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Jiankun Liu has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
Jianhua Wang
State Key Laboratory of Electrical Insulation and Power Equipment, Xi'an Jiaotong University, Xi'an, Shaanxi, China
4 shared publicationsYingsan Geng
State Key Laboratory of Electrical Insulation and Power Equipment, Xi'an Jiaotong University, Xi'an, Shaanxi, China
4 shared publications- Zhenxing Wang
State Key Laboratory of Electrical Insulation and Power Equipment, Xi’an Jiaotong University, Xi’an, People’s Republic of China
4 shared publications Zhiyuan Liu
State Key Laboratory of Electrical Insulation and Power Equipment, Xi'an Jiaotong University, Xi'an, Shaanxi, China
4 shared publicationsHaoran Wang
Department of Electrical Engineering, Xi'an Jiaotong University, Xi'an, China
2 shared publications- Liqiong Sun
State Key Laboratory of Electrical Insulation and Power Equipment, Xi’an Jiaotong University , Xi’an 710049, China
2 shared publications
Latest Publications
- 17 December 2018
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 52 (7) , 075205
The effect and dynamic behavior of particles in high-current vacuum arc interruptions
Microparticles produced by high current vacuum arcs significantly reduce the insulation performance of vacuum interrupters. The objective of this paper is to observe the generation and dynamics of microparticles during the arcing and post-arcing period, and to further reveal the possible effects of particles during interruption of a high current vacuum arc. A plasma diagnosis system based on a laser-shadow technique was used to measure the particles in a demountable vacuum chamber. The results show that contact materials affect particle generation patterns. For a CuCr contact with a higher proportion of chromium, the formation of a melting pool is much more difficult and the flow of liquid metal on the surface can be suppressed, which also impedes the formation of particles. Moreover, reignition after arc extinction was found to be triggered by some incandescent particles. These hot particles have two effects on breakdown events during the post-arcing phase: they trigger a micro-discharge between a particle and the electrode, and new weak points are left on the surface that enhance the local field. More crucially, the lifetime of spontaneous particles spans up to hundreds of milliseconds after current zero, which indicates that long-delayed breakdown is correlated with the existence of particles. In addition, some particles could remain suspended near the electrode or oscillate between the contacts. The dynamic behavior of these particles can significantly lower the breakdown threshold and increase the possibility of breakdown.
- 17 December 2018
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 52 (7) , 075205
The effect and dynamic behavior of particles in high-current vacuum arc interruptions
Microparticles produced by high current vacuum arcs significantly reduce the insulation performance of vacuum interrupters. The objective of this paper is to observe the generation and dynamics of microparticles during the arcing and post-arcing period, and to further reveal the possible effects of particles during interruption of a high current vacuum arc. A plasma diagnosis system based on a laser-shadow technique was used to measure the particles in a demountable vacuum chamber. The results show that contact materials affect particle generation patterns. For a CuCr contact with a higher proportion of chromium, the formation of a melting pool is much more difficult and the flow of liquid metal on the surface can be suppressed, which also impedes the formation of particles. Moreover, reignition after arc extinction was found to be triggered by some incandescent particles. These hot particles have two effects on breakdown events during the post-arcing phase: they trigger a micro-discharge between a particle and the electrode, and new weak points are left on the surface that enhance the local field. More crucially, the lifetime of spontaneous particles spans up to hundreds of milliseconds after current zero, which indicates that long-delayed breakdown is correlated with the existence of particles. In addition, some particles could remain suspended near the electrode or oscillate between the contacts. The dynamic behavior of these particles can significantly lower the breakdown threshold and increase the possibility of breakdown.
- 1 September 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 1, 19-22
The Effect of Contact Material on Particles Behavior in High-Current Vacuum Arcs
Micro particles produced by high-current vacuum arcs significantly reduce the insulation performance of vacuum interrupters. The objective of this paper is to observe the effect of contact materials on the behavior of micro particles during the arcing and post-arcing period, and to reveal possible reason for the late breakdown triggered by them. A plasma diagnosis system based on laser-shadow technique was established to measure the particles in a demountable vacuum chamber. The results illustrate that the patterns of particles generation have significant difference due to the contact materials. CuCr10 contacts tended to present obvious flowing liquid metal on the surface, forming protrusions on it which became to be particles source. On the contrary, CuCr50 contacts scarcely produced obvious molten clumps and particles were ejected directly from erosion area the electrode surface, furthermore, particles ejection could sometimes be restrained by the arc pressure. Moreover, the residual particles after the current zero between the electrode gap dramatically decreased the insulation performance and played a significant role in the re-ignition. A delayed breakdown could be initiated by the micro particle existed several milliseconds after arc extinction.
- 1 September 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 1, 19-22
The Effect of Contact Material on Particles Behavior in High-Current Vacuum Arcs
Micro particles produced by high-current vacuum arcs significantly reduce the insulation performance of vacuum interrupters. The objective of this paper is to observe the effect of contact materials on the behavior of micro particles during the arcing and post-arcing period, and to reveal possible reason for the late breakdown triggered by them. A plasma diagnosis system based on laser-shadow technique was established to measure the particles in a demountable vacuum chamber. The results illustrate that the patterns of particles generation have significant difference due to the contact materials. CuCr10 contacts tended to present obvious flowing liquid metal on the surface, forming protrusions on it which became to be particles source. On the contrary, CuCr50 contacts scarcely produced obvious molten clumps and particles were ejected directly from erosion area the electrode surface, furthermore, particles ejection could sometimes be restrained by the arc pressure. Moreover, the residual particles after the current zero between the electrode gap dramatically decreased the insulation performance and played a significant role in the re-ignition. A delayed breakdown could be initiated by the micro particle existed several milliseconds after arc extinction.
- 1 September 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 1, 313-316
Investigation of Vacuum Arc Extinction Process by Planar Laser-Induced Fluorescence
Since metallic vapor could play a vital role in the post-arc breakdown which directly lead to a failure of interruption, it is of importance to research the evolution of metallic vapor in the gap near current zero for better understanding of the post-arc phenomena in a vacuum interrupter. In this work, the technique of planar laser-induced fluorescence(PLIF) is adopted for measuring the 2-D map of copper vapor distribution between a pair of copper contacts. By varying the probing timing of laser sheet, the evolution process of copper vapor near current zero is obtained. It is found that when vacuum arc operates in the anode spot mode, though after current zero, there still exists intense evaporation process from melted anode. The density of evaporated metallic vapor near anode at current zero is about 6×10 18 m -3 after calibration.
- 1 September 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 1, 313-316
Investigation of Vacuum Arc Extinction Process by Planar Laser-Induced Fluorescence
Since metallic vapor could play a vital role in the post-arc breakdown which directly lead to a failure of interruption, it is of importance to research the evolution of metallic vapor in the gap near current zero for better understanding of the post-arc phenomena in a vacuum interrupter. In this work, the technique of planar laser-induced fluorescence(PLIF) is adopted for measuring the 2-D map of copper vapor distribution between a pair of copper contacts. By varying the probing timing of laser sheet, the evolution process of copper vapor near current zero is obtained. It is found that when vacuum arc operates in the anode spot mode, though after current zero, there still exists intense evaporation process from melted anode. The density of evaporated metallic vapor near anode at current zero is about 6×10 18 m -3 after calibration.
- 1 October 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 90-93
Chromium vapor density measurement by optical absorption spectroscopy of diffuse vacuum arcs in vacuum interrupters
The metallic vapor density in vacuum arc in a vacuum interrupter is crucial for deeper understanding of the anodic activities and dielectric recovery process. In this work, the objective is to measure the Cr metallic vapor density and its axial distribution along the gap in the vacuum arc between chromium contacts. The method of the optical absorption spectroscopy (OAS) using a broadband light source is adopted. The result shows that when the vacuum arc operates in diffuse mode, the maxima of metallic vapor density distribution occurs in the vicinity of electrodes during arcing period, representing the cathodic vapor source and anodic vapor source. Following the decrease of arc current, the metallic vapor density decrease as well. At current zero, the metallic vapor has a nearly uniform distribution in the gap of about 3×10 17 m -3 .
- 1 October 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 90-93
Chromium vapor density measurement by optical absorption spectroscopy of diffuse vacuum arcs in vacuum interrupters
The metallic vapor density in vacuum arc in a vacuum interrupter is crucial for deeper understanding of the anodic activities and dielectric recovery process. In this work, the objective is to measure the Cr metallic vapor density and its axial distribution along the gap in the vacuum arc between chromium contacts. The method of the optical absorption spectroscopy (OAS) using a broadband light source is adopted. The result shows that when the vacuum arc operates in diffuse mode, the maxima of metallic vapor density distribution occurs in the vicinity of electrodes during arcing period, representing the cathodic vapor source and anodic vapor source. Following the decrease of arc current, the metallic vapor density decrease as well. At current zero, the metallic vapor has a nearly uniform distribution in the gap of about 3×10 17 m -3 .