AVAbbas Vosoogh

Abbas Vosoogh

*This is an algorithmically generated author record based on publicly available information.

Abbas Vosoogh has a total of 29 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Compact Low-Loss Slot Array Antenna Based on Strip-on-Substrate Coaxial Multi-Layer Waveguide for 77 GHz Automotive Radar

    by Enlin Wang, Abbas Vosoogh, Carlo Bencivenni, Sadegh Mansouri Moghaddam, Jian Yang

    A compact, ultra-thin, low-loss and low-cost slot array antenna is presented for 77-GHz automotive radar, offering high polarization purity. Using strip-on-substrate coaxial multi-layer waveguide (SCMLW) technology, the design features a linear dogbone-shaped non-tilted centrally aligned slot array fed by a meandered metallic strip of the SCMLW. The proposed coaxial line-fed slotted antenna eliminates the angular and positional offset of slot employed in earlier designs, which are known to increase cross-polarization. Four prototypes, two 1×6 and two 2×6 slot arrays, were fabricated by chemical etching on a single platform with an overall thickness of only 0.9 mm, where long slits are introduced to improve radiation patterns. Measurements over 76–81 GHz show reflection coefficients better than $-10$ dB and relative cross-polarization levels below -29 dB for all prototypes, confirming their suitability for millimeter-wave automotive radar applications.

  • E-Band Automotive Radar Array Antenna in Multilayer Waveguide Technology With Reduced Sidelobe and Cross-Polarization Level

    by Coen van de Ven, Carlos Biurrun-Quel, Abbas Vosoogh, Andrés Alayón Glazunov

    This paper introduces a novel excitation technique for a slotted rectangular coaxial line implemented in multi-layer waveguide technology. The proposed approach effectively mitigates the previously observed issue of elevated cross-polarization levels. Cross-polarization reduction is achieved by using dogbone-shaped slots excited by a meandered coaxial line feed positioned beneath them. A new antenna element comprising two columns of five slots has been designed for medium-range automotive radar applications. An eight-channel MIMO array based on the proposed element is designed and experimentally validated. At 76–81 GHz, the 4-Tx/4-Rx array achieves measured half-power beamwidths of approximately $50^\circ$ (azimuth) and $25^\circ$ (elevation), sidelobe levels below $-20$ dB, and a cross-polarization ratio better than $-30$ dB at broadside.


  • Open Access

    Gap Waveguide-Based MMIC Packaging Solutions for Compact RF Front-End Modules at 100 GHz

    by Juan-Luis Albadalejo Lijarcio, Abbas Vosoogh, Thomas Emanuelsson, Jian Yang, Ashraf Uz Zaman

    This paper presents two innovative packaging techniques for Monolithic Microwave Integrated Circuits (MMICs) designed for multilayer waveguide-based antennas operating near 100 GHz. The first technique involves a transition from a high-permittivity Gallium Arsenide (GaAs) MMIC to a rectangular waveguide using conventional bondwires as the coupling structure within the W-band. This approach enables seamless integration of any off-the-shelf RF chip into waveguide antenna modules without modifying the ground-signal-ground (GSG) pads or adding passive transition substrates. An electromagnetic bandgap (EBG) structure, implemented using metallic pins, effectively suppresses unwanted field propagation. Measurements of a back-to-back (B2B) prototype indicate a reflection coefficient below -10 dB and an average insertion loss of 0.12 dB for a single transition across a bandwidth from 90 to 97 GHz (10.5% relative bandwidth). The second technique introduces a contactless vertical transition from a high-permittivity Alumina (Al2O3) based microstrip line to a waveguide, targeting F-band applications. This proposed concept employs a patch-shaped probe placed on the substrate to couple electromagnetic waves to an H-shaped waveguide aperture positioned above the probe. Experimental results demonstrate a reflection coefficient below -10 dB and an average insertion loss of 0.17 dB over a frequency range of 102 to 120 GHz (15.3% relative bandwidth). In addition, the impact of manufacturing and assembly tolerances on the performance of both transitions is analyzed.

  • A Wideband 8 × 8 Slot Array Antenna Using Gap Waveguide MLW Coaxial Line Technology for mmWave Applications

    by Ali Farahbakhsh, Davood Zarifi, Abbas Vosoogh, Carlo Bencivenni, Michal Mrozowski

    The paper presents a wideband 8×8-element slot antenna array operating in the E-band. The proposed design employs a low-loss coaxial waveguide transmission line filled with air implemented using multilayer waveguide (MLW) technology by vertically stacking thin, unconnected metal plates to meet the typical radiation pattern and bandwidth requirements of a slot antenna array. To validate the concept, the simulation and measurement results of an 8×8 slot antenna array are presented. The proposed antenna array exhibits |S11| < -10 dB and a realized gain around 26.4 dBi from 70.7 GHz to 82.4 GHz. The main advantages offered by the MLW coaxial line technology are low-profile, low-loss, mass-production capability, and low-cost at mm Wave frequencies.


  • Open Access

    Realisation of an E‐Plane Metal‐Insert Filter at E‐Band Based on Multi‐Layer Waveguide With Pin Array Electromagnetic Band Gap

    by Morteza Rezaee, Abbas Vosoogh, Ali Mehrdadian

    In this paper, a multi‐layer waveguide (MLW) bandpass filter is realised by stacking thin metal layers at E‐band. In order to eliminate the leakage between layers, an electromagnetic band gap (EBG) pin array is utilised. The periodic pin texture is created by 3D chemical etching on the layers. The thickness of layers and height of pins are selected properly to provide a stopband at operating frequency band of interest. A thin metal layer at the middle of the waveguide channel is used to realise the cavities and coupling slits of the filter. A seventh order metal‐insert E‐plane filter with frequency pass band of 69.5–76 GHz is designed and fabricated. The designed MLW bandpass filter is fabricated in brass and copper metal sheets with insertion loss of around 1.5 and 1.1 dB, respectively. Several filter prototypes are fabricated and studied to verify the repeatability of the fabrication and assembly processes.

  • Low-Cost Center-Fed Slot Array Based on Gap Waveguide MLW Coaxial Line Technology for E-Band Automotive Radar

    by Juan-Luis Albadalejo Lijarcio, Abbas Vosoogh, Carlo Bencivenni, Ashraf Uz Zaman

    This paper introduces an innovative center-fed slot array utilizing multilayer waveguide (MLW) coaxial line technology. The array consists of 3 columns with 8 in-line slots to narrow the beamwidth in the E-plane and H-plane, thus increasing the gain in the boresight direction. The slots are excited by the longitudinal currents created by a transverse electromagnetic (TEM) wave, which propagates within the coaxial line placed beneath them. Each column of the array is fed by a coupling slot placed in the center, thus mitigating beam squint over the operating frequency band. The aforementioned coupling slot directly couples the fields from an additional feeding line used for routing. The proposed design consists of 6 unconnected metal sheets which are stacked together. The use of gap waveguide technology prevents field leakage from any potential air gap among the layers, thus making assembly easier and more tolerant. A prototype with 2 side-by-side antennas is manufactured by using a quick, cost-effective, and suitable for mass production metal sheet process. The measurements agree very well with the simulations within the frequency band of interest from 76 to 81 GHz. The measured return loss is better than 10 dB. Furthermore, the realized gain is around 16 dBi with 37 degrees beamwidth in the E-plane and 16 degrees beamwidth in the H-plane. Additionally, the measurements of a back-to-back prototype show a loss of around 0.0179 dB/mm at 77 GHz for the coaxial transmission line. The properties of the radiation pattern make this element suitable for automotive long-range radar (LRR) applications.


  • Open Access

    Substrateless Packaging for a D-Band MMIC Based on a Waveguide with a Glide-Symmetric EBG Hole Configuration

    by Weihua Yu, Abbas Vosoogh, Bowu Wang, Zhongxia Simon He

    This paper presents a novel substrateless packaging solution for the D-band active e mixer MMIC module, using a waveguide line with a glide-symmetric periodic electromagnetic bandgap (EBG) hole configuration. The proposed packaging concept has the benefit of being able to control signal propagation behavior by using a cost-effective EBG hole configuration for millimeter-wave- and terahertz (THz)-frequency-band applications. Moreover, the mixer MMIC is connected to the proposed hollow rectangular waveguide line via a novel wire-bond wideband transition without using any intermediate substrate. A simple periodical nail structure is utilized to suppress the unwanted modes in the transition. Additionally, the presented solution does not impose any limitations on the chip’s dimensions or shape. The packaged mixer module shows a return loss lower than 10 dB for LO (70–85 GHz) and RF (150–170 GHz) ports, achieving a better performance than that of traditional waveguide transitions. The module could be used as a transmitter or receiver, and the conversion loss shows good agreement in multiple samples. The proposed packaging solution has the advantages of satisfactory frequency performance, broadband adaptability, low production costs, and excellent repeatability for millimeter-wave- and THz-band systems, which would facilitate the commercialization of millimeter-wave and THz products.


  • Compact Integrated Full-Duplex Gap Waveguide-Based Radio Front End For Multi-Gbit/s Point-to-Point Backhaul Links at E-Band

    by Abbas Vosoogh, Milad Sharifi Sorkherizi, Vessen Vassilev, Ashraf Uz Zaman, Zhongxia Simon He, Jian Yang, Ahmed A. Kishk, Herbert Zirath

    This paper presents the design and realization of a high data rate radio front-end module for point-to-point backhaul links at E-band. The design module consists of four vertically stacked unconnected metal layers without any galvanic and electrical contact requirements among the building blocks, by using gap waveguide technology. The module components are a high-gain array antenna, diplexer, and circuitry consisting of a transmitter (Tx) and a receiver (Rx) monolithic microwave integrated circuits (MMICs) on a carrier board, which is successfully integrated into one package with a novel architecture and a compact form. The diplexer consists of two direct-coupled cavity bandpass filters with channels at 71-76 GHz and 81-86 GHz with a measured return loss of 15 dB and an isolation greater than 50 dB. A wideband $16x16$ slot array antenna with a measured gain of more than 31 dBi is used to provide high directivity. The measured results show that the packaged transmitter provides a conversion gain of 22 and 20 dB at 76 and 86 GHz, respectively, with an output power of 14 and 16 dBm at 1-dB gain compression point, at the same frequencies. The packaged receiver shows an average conversion gain of 20 dB at 71-76-GHz and 24 dB at 81-86-GHz bands. A real-time wireless data transmission is successfully demonstrated with a data rate of 8 Gbit/s using 32-quadrature amplitude modulated signal over 1.8-GHz channel bandwidth with spectral efficiency of 4.44 bit/s/Hz. The proposed radio front end provides the advantages of low loss, high efficiency, compact integration, and a simple mechanical assembly, which makes it a suitable solution for small-cell backhaul links.


  • Novel Air-Filled Waveguide Transmission Line Based on Multilayer Thin Metal Plates

    by Abbas Vosoogh, Herbert Zirath, Zhongxia Simon He

    This paper presents a novel way of constructing wave guiding structures by stacking several thin metal plates for millimeter-wave and terahertz applications. The metallic layers do not require any electrical contacts among them. An air-filled multi-layer waveguide (MLW) transmission line is successfully designed and manufactured at D-band. Five vertically stacked thin metal layers are used to form an air-filled rectangular waveguide line. The layers are simply assembled by allowing a small air gap among them, without the need of using advanced manufacturing methods such as adhesive bonding techniques. The possible field leakage due to the air gaps is prevented by using an electromagnetic band gap (EBG) structure, consisting of glide-symmetric holes. A straight MLW line and a line with a double 90° bends are fabricated by using chemical metal etching, as a proof of concept. The measurement results of the straight line show that the reflection coefficient is better than -18 dB with average insertion loss of 0.02 dB/mm over the frequency band 110-170 GHz. For the double 90° bends line, the reflection coefficient is better than -18 dB with a similar average insertion loss of 0.02 dB/mm over the frequency band 110-150 GHz. The proposed concept could be an excellent candidate for designing compact and thin passive waveguide components and active components packaging, with a great potential for low-cost, light weight and mass-producible at millimeter-wave frequencies.