Zhou Yu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Zhou Yu has a total of 111 co-authors. Here are the top co-authors by number of shared publications:
- Yong Zhao
Fujian Normal University
14 shared publications Lian Liu
Key Laboratory of Magnetic Suspension Technologies and Maglev Vehicle, College of Electrical Engineering, Southwest Jiaotong University, Chengdu 610031, People’s Republic of China
11 shared publicationsWentao Wang
Key Laboratory of Magnetic Suspension Technology and Maglev Vehicle (Ministry of Education), School of Physical Science and Technology, Southwest Jiaotong University, Chengdu, China
8 shared publicationsXiaguang Sun
Southwest Institute of Physics, Chengdu, China
8 shared publicationsYong Zhao
College of Materials and Energy, Guangan Institute of Technology, Guangan, P. R. China
8 shared publications- Yong Zhang
Southwest Jiaotong University
7 shared publications
Latest Publications
- 11 September 2026
- Published by Springer Nature in Applied Physics A
- Vol. 132 (10) , 1007
Superconducting properties improvement of Nb3Al wire via pre-heat-treatment of Nb(Al)ss parent wires
- 11 September 2026
- Published by Springer Nature in Applied Physics A
- Vol. 132 (10) , 1007
Superconducting properties improvement of Nb3Al wire via pre-heat-treatment of Nb(Al)ss parent wires
- 27 July 2026
- Published by Springer Nature in Applied Physics A
- Vol. 132 (8) , 791
Superconducting properties enhancement of Nb3(Al, Ge) wires by adding nano size SnO2
- 27 July 2026
- Published by Springer Nature in Applied Physics A
- Vol. 132 (8) , 791
Superconducting properties enhancement of Nb3(Al, Ge) wires by adding nano size SnO2
- 1 December 2025
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 38 (12) , 125022
Electromechanical properties of nano silver joints for YBCO coated conductors under axial tensile stress
Effective joining techniques are fundamental in the development of superconducting magnets utilizing YBCO coated conductors or tapes. In this study, the electromechanical performance of YBCO joints under axial tensile stress, fabricated by a nano silver low-temperature sintering method, were comprehensively investigated via varying overlap lengths and nano silver coating thickness. For a single joint, resistance remains constant under increasing loads and reduces when extending the lapped length and rises with thickening of the nano silver paste. The joints with lapped lengths of 2 and 3 cm exhibit larger tensile stress of 500 MPa, comparable to that of an unjoined single tape. However, a thicker nano paste coating thickness of 100 and 150 μ m results in a decrease in joints tensile stress to 450 MPa. Initially, the joints demonstrate lower I c values than the original tape under a zero-force state. By thickening the silver stabilizer, the stress concentration at the joint edges was suppressed and I c was successfully recovered while maintaining the previously achieved tensile stress levels.
- 1 December 2025
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 38 (12) , 125022
Electromechanical properties of nano silver joints for YBCO coated conductors under axial tensile stress
Effective joining techniques are fundamental in the development of superconducting magnets utilizing YBCO coated conductors or tapes. In this study, the electromechanical performance of YBCO joints under axial tensile stress, fabricated by a nano silver low-temperature sintering method, were comprehensively investigated via varying overlap lengths and nano silver coating thickness. For a single joint, resistance remains constant under increasing loads and reduces when extending the lapped length and rises with thickening of the nano silver paste. The joints with lapped lengths of 2 and 3 cm exhibit larger tensile stress of 500 MPa, comparable to that of an unjoined single tape. However, a thicker nano paste coating thickness of 100 and 150 μ m results in a decrease in joints tensile stress to 450 MPa. Initially, the joints demonstrate lower I c values than the original tape under a zero-force state. By thickening the silver stabilizer, the stress concentration at the joint edges was suppressed and I c was successfully recovered while maintaining the previously achieved tensile stress levels.
- 28 January 2025
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 38 (3)
New-route of flux pinning enhancement in Nb3Al superconductor: density and orientation regulation of stacking faults by nano-oxide particles
The mechanism of critical current density (Jc) enhancement in rapid heating, quenching and transformation (RHQT) Nb3Al wires with nanoparticles was investigated from microscopic defects. As shown in transmission electron microscopy (TEM) results, stacking faults (SF) density in RHQT Nb3Al could be improved by incorporating nano-oxide particles, because the nanoparticles distorted the Nb3Al crystal lattice and the expansion of the distortion generated stacking faults. The macroscopic measurements based on electron backscatter diffraction (EBSD) showed that many stacking faults were parallel to the Lorentz force (FL//SF) in the pure sample, but orientation of stacking faults distributed randomly in the Nb3Al wires with nano oxide. Stacking faults that were normal to the Lorentz force (FL⊥SF) could hinder the motion of flux lines effectively and thus enhance the total flux pinning force (Fp). As a result, Jc of incorporated nano oxide Nb3Al wires were significantly elevated, where 1 at.% nano-ZrO2 and 1 at.% nano-Dy2O3 sample severally exhibited Jc values of 1.86×105 A/cm2 and 1.95×105 A/cm2@4.2 K,12 T, which improved by about 60% compared to the pure sample. The density and orientation regulation of stacking faults in RHQT Nb3Al revealed the new mechanism of Jc enhancement, which provided a new route to further improve the high-field Jc of Nb3A in future research.
- 28 January 2025
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 38 (3)
New-route of flux pinning enhancement in Nb3Al superconductor: density and orientation regulation of stacking faults by nano-oxide particles
The mechanism of critical current density (Jc) enhancement in rapid heating, quenching and transformation (RHQT) Nb3Al wires with nanoparticles was investigated from microscopic defects. As shown in transmission electron microscopy (TEM) results, stacking faults (SF) density in RHQT Nb3Al could be improved by incorporating nano-oxide particles, because the nanoparticles distorted the Nb3Al crystal lattice and the expansion of the distortion generated stacking faults. The macroscopic measurements based on electron backscatter diffraction (EBSD) showed that many stacking faults were parallel to the Lorentz force (FL//SF) in the pure sample, but orientation of stacking faults distributed randomly in the Nb3Al wires with nano oxide. Stacking faults that were normal to the Lorentz force (FL⊥SF) could hinder the motion of flux lines effectively and thus enhance the total flux pinning force (Fp). As a result, Jc of incorporated nano oxide Nb3Al wires were significantly elevated, where 1 at.% nano-ZrO2 and 1 at.% nano-Dy2O3 sample severally exhibited Jc values of 1.86×105 A/cm2 and 1.95×105 A/cm2@4.2 K,12 T, which improved by about 60% compared to the pure sample. The density and orientation regulation of stacking faults in RHQT Nb3Al revealed the new mechanism of Jc enhancement, which provided a new route to further improve the high-field Jc of Nb3A in future research.
- 22 January 2025
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 38 (2) , 025010
Obtaining highly homogeneous Nb3Al superconductor with improved critical current density by understanding the phase evolution sequence of mono-core and multifilamentary wires
Mono-core and multifilamentary (MF) Nb–Al precursor wires were obtained by a rapid heating, quenching and transformation (RHQT) process to investigate the phase evolution sequence, in order to find a way to fabricate highly homogeneous Nb3Al superconductor. The microstructure and composition distribution of the Nb3Al superconductor is the same as that of quenched wires. Phase evolution (1) in mono-core wire is as follows: Nb + Al→ eutectic phase +Nb2Al + Nb3Al→ grid-shape Nb(Al)ss→ band-like Nb(Al)ss, where nonuniform microstructure is formed in the transformed Nb3Al because the Nb layer is too thick; (2) in MF wire is as follows: Nb + Al→ Nb2Al + Nb3Al→solid Nb(Al)ss→ two-phase-segregation→ liquid Nb(Al)ss, where much thinner Nb layers completely react to Nb3Al and Nb2Al, but the Al content of Nb3Al phase is still inhomogeneous. Restricted by the precursor wire fabrication ability, further decreasing the Nb layer thickness fails to improve the homogeneity of Nb3Al phase. Therefore, the author’s route of afresh heating of the quenched Nb2Al + Nb3Al wire was carried out to increase the atomic diffusion coefficient due to the non-equilibrium crystal defects present in the quenched wires. As a result, a highly composition homogeneous Nb3Al phase was realized in the whole superconducting filament with a scale of about ∼100 μm. The magnetic critical current density (J c) of the afresh heated Nb3Al superconductor reached 2066 A mm−2@12 T, 4.2 K, showing an improvement of about 60% compared to the best J c result for the MF RHQT Nb3Al wire.
- 22 January 2025
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 38 (2) , 025010
Obtaining highly homogeneous Nb3Al superconductor with improved critical current density by understanding the phase evolution sequence of mono-core and multifilamentary wires
Mono-core and multifilamentary (MF) Nb–Al precursor wires were obtained by a rapid heating, quenching and transformation (RHQT) process to investigate the phase evolution sequence, in order to find a way to fabricate highly homogeneous Nb3Al superconductor. The microstructure and composition distribution of the Nb3Al superconductor is the same as that of quenched wires. Phase evolution (1) in mono-core wire is as follows: Nb + Al→ eutectic phase +Nb2Al + Nb3Al→ grid-shape Nb(Al)ss→ band-like Nb(Al)ss, where nonuniform microstructure is formed in the transformed Nb3Al because the Nb layer is too thick; (2) in MF wire is as follows: Nb + Al→ Nb2Al + Nb3Al→solid Nb(Al)ss→ two-phase-segregation→ liquid Nb(Al)ss, where much thinner Nb layers completely react to Nb3Al and Nb2Al, but the Al content of Nb3Al phase is still inhomogeneous. Restricted by the precursor wire fabrication ability, further decreasing the Nb layer thickness fails to improve the homogeneity of Nb3Al phase. Therefore, the author’s route of afresh heating of the quenched Nb2Al + Nb3Al wire was carried out to increase the atomic diffusion coefficient due to the non-equilibrium crystal defects present in the quenched wires. As a result, a highly composition homogeneous Nb3Al phase was realized in the whole superconducting filament with a scale of about ∼100 μm. The magnetic critical current density (J c) of the afresh heated Nb3Al superconductor reached 2066 A mm−2@12 T, 4.2 K, showing an improvement of about 60% compared to the best J c result for the MF RHQT Nb3Al wire.
- 5 January 2025
- Published by Elsevier in Journal of Magnetism and Magnetic Materials
- Vol. 614
Study on the improvement of MgB2 grain connectivity by rapid heating and quenching annealing
- 5 January 2025
- Published by Elsevier in Journal of Magnetism and Magnetic Materials
- Vol. 614
Study on the improvement of MgB2 grain connectivity by rapid heating and quenching annealing
- 13 July 2023
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 36 (8) , 085016
Low-resistance joints for YBCO-coated conductors with Ag nanoparticle paste
Due to the limited available piece length of YBCO-coated conductors (i.e. tapes or wires) and the different requirements for magnetic field, joints are inevitable for manufacturing high-temperature superconducting magnets. In this study, a sintering nano-silver (Ag) process was developed and used to connect YBCO tapes stabilized by anAg layer with low-temperature and short-time sintering of Ag nanoparticle (NP) paste. The thermodynamic characteristics of Ag NP paste were explored using a TG/DSC setup. The effects of sintering temperature, mechanical pressure and lapped length on microstructures and electrical properties of joints were comprehensively investigated. It is found that the pre-volatilization of low-boiling-point solvent in the paste is beneficial to improve the densification of sintered structure, thus contributing to increasing the critical current I c of the joint. With increasing sintering temperature, the I c of the joint will be close to that of the virgin tape, and the joint resistance experiences small fluctuations, but joint connectivity is enhanced. As the temperature reaches 205 °C, I c decreases to 84% of the virgin tape, and joint resistance increases obviously. In addition, the axial tension strength at room temperature is improved with the increase in mechanical pressure, while the resistance does not demonstrate distinct variation. Considering the electromechanical properties, the optimal joining process is determined as sintering at 180 °C and 30 MPa for 10 min. The joint with this technology possesses a closely connected interface and a well-sintered nano-Ag microstructure with pores. By further extending the lapped length, a YBCO joint resistivity as low as ∼10.56 nΩ cm2 is obtained, which is around a quarter of that of the soldering joint, and the process is much easier than that of the Ag diffusion joint.
- 13 July 2023
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 36 (8) , 085016
Low-resistance joints for YBCO-coated conductors with Ag nanoparticle paste
Due to the limited available piece length of YBCO-coated conductors (i.e. tapes or wires) and the different requirements for magnetic field, joints are inevitable for manufacturing high-temperature superconducting magnets. In this study, a sintering nano-silver (Ag) process was developed and used to connect YBCO tapes stabilized by anAg layer with low-temperature and short-time sintering of Ag nanoparticle (NP) paste. The thermodynamic characteristics of Ag NP paste were explored using a TG/DSC setup. The effects of sintering temperature, mechanical pressure and lapped length on microstructures and electrical properties of joints were comprehensively investigated. It is found that the pre-volatilization of low-boiling-point solvent in the paste is beneficial to improve the densification of sintered structure, thus contributing to increasing the critical current I c of the joint. With increasing sintering temperature, the I c of the joint will be close to that of the virgin tape, and the joint resistance experiences small fluctuations, but joint connectivity is enhanced. As the temperature reaches 205 °C, I c decreases to 84% of the virgin tape, and joint resistance increases obviously. In addition, the axial tension strength at room temperature is improved with the increase in mechanical pressure, while the resistance does not demonstrate distinct variation. Considering the electromechanical properties, the optimal joining process is determined as sintering at 180 °C and 30 MPa for 10 min. The joint with this technology possesses a closely connected interface and a well-sintered nano-Ag microstructure with pores. By further extending the lapped length, a YBCO joint resistivity as low as ∼10.56 nΩ cm2 is obtained, which is around a quarter of that of the soldering joint, and the process is much easier than that of the Ag diffusion joint.