Xiaoxian Liu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Xiaoxian Liu has a total of 62 co-authors. Here are the top co-authors by number of shared publications:
- Zhangming Zhu
Xidian University
39 shared publications - Yintang Yang
Xidian University
14 shared publications - Yang Liu
Key Laboratory of Analog Integrated Circuits and Systems, Ministry of Education, School of Integrated Circuits, Xidian University, Xian, China
13 shared publications - Xiangkun Yin
Xidian University
12 shared publications - Lei Wang
China Electronic Product Reliability and Environmental Testing Research Institute, Guangzhou, China
11 shared publications - Qijun Lu
Shaanxi Key Laboratory of Integrated Circuits and Systems, School of Microelectronics, Xidian University, Xi’an, China
11 shared publications
Latest Publications
- 8 May 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 73 (6) , 638-642
An Ultra-Compact Doherty Power Amplifier Based on Reciprocal Three-Coil-Coupled-Network
This brief presents an ultra-compact Doherty PA based on the three-coil-coupling-network (TCCN). The TCCN supports load modulation while satisfying impedance matching, and imposes minimal constraints on the output parasitic capacitance of the transistors. Moreover, a detailed parametric analysis is conducted, clarifying the relationship between the traditional 90° equivalent lumped matching network and the specific parameters of the TCCN. A Ka-band Doherty PA prototype is fabricated in 65nm CMOS process to validate the effectiveness of this method, with a total core area of 0.074 mm2. At 27GHz, the proposed DPA achieves a peak power output of 21.9 dBm, a peak power-added efficiency of 27.8%, a power-added efficiency at 6dB power back-off of 18.76%, with a maximum power density of 2.09 W/mm2.
- 8 May 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 73 (6) , 638-642
An Ultra-Compact Doherty Power Amplifier Based on Reciprocal Three-Coil-Coupled-Network
This brief presents an ultra-compact Doherty PA based on the three-coil-coupling-network (TCCN). The TCCN supports load modulation while satisfying impedance matching, and imposes minimal constraints on the output parasitic capacitance of the transistors. Moreover, a detailed parametric analysis is conducted, clarifying the relationship between the traditional 90° equivalent lumped matching network and the specific parameters of the TCCN. A Ka-band Doherty PA prototype is fabricated in 65nm CMOS process to validate the effectiveness of this method, with a total core area of 0.074 mm2. At 27GHz, the proposed DPA achieves a peak power output of 21.9 dBm, a peak power-added efficiency of 27.8%, a power-added efficiency at 6dB power back-off of 18.76%, with a maximum power density of 2.09 W/mm2.
- 18 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 74 (5) , 4310-4324
Comprehensive Design Approach for Ka-Band Compact Filtering Power Amplifier Using Hybrid Notch and MCCR for Dual-Side Suppression
This article presents a compact Ka-band filter power amplifier (FPA) that achieves suppression on both sides of the passband by introducing the hybrid notch and magnetically and capacitively coupled resonator (HN-MCCR). The proposed HN-MCCR effectively combines the mechanism for introducing multiple transmission zeros (TZs) with an asymmetric impedance matching network. The theoretical analysis not only provides the first in-depth analysis of asymmetric magnetically and capacitively coupled resonator (MCCR) and HN-MCCR with introduced TZs from a design perspective, but also presents a specific calculation method and procedures for each parameter, which distinguishes it from previous trend analyses. In addition, a differential magnetic coupled notch filter (DMCNF) is proposed to reduce the core area. The PA prototype, fabricated in a 65-nm CMOS process, occupies a core area of 0.067mm2. It achieves a gain of 22.9dB at 26GHz with 3-dB bandwidth from 22.4 to 27GHz, and a peak power output of 17.7dBm with a peak power-added efficiency of 26.95%. Measurement results indicate the introduction of TZs on both sides of the passband. Out-of-band (OOB) suppression exceeds 25.1dBc below 18GHz and above 33GHz, and reaches up to 50.1dBc below 14.5GHz and above 39GHz. This capability effectively attenuates OOB energy, reduces image signal effects, and makes it a potential candidate for 5G large-scale array applications. To the best of the authors’ knowledge, this is the first article that thoroughly analyzes and implements an FPA with bilateral suppression.
- 18 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 74 (5) , 4310-4324
Comprehensive Design Approach for Ka-Band Compact Filtering Power Amplifier Using Hybrid Notch and MCCR for Dual-Side Suppression
This article presents a compact Ka-band filter power amplifier (FPA) that achieves suppression on both sides of the passband by introducing the hybrid notch and magnetically and capacitively coupled resonator (HN-MCCR). The proposed HN-MCCR effectively combines the mechanism for introducing multiple transmission zeros (TZs) with an asymmetric impedance matching network. The theoretical analysis not only provides the first in-depth analysis of asymmetric magnetically and capacitively coupled resonator (MCCR) and HN-MCCR with introduced TZs from a design perspective, but also presents a specific calculation method and procedures for each parameter, which distinguishes it from previous trend analyses. In addition, a differential magnetic coupled notch filter (DMCNF) is proposed to reduce the core area. The PA prototype, fabricated in a 65-nm CMOS process, occupies a core area of 0.067mm2. It achieves a gain of 22.9dB at 26GHz with 3-dB bandwidth from 22.4 to 27GHz, and a peak power output of 17.7dBm with a peak power-added efficiency of 26.95%. Measurement results indicate the introduction of TZs on both sides of the passband. Out-of-band (OOB) suppression exceeds 25.1dBc below 18GHz and above 33GHz, and reaches up to 50.1dBc below 14.5GHz and above 39GHz. This capability effectively attenuates OOB energy, reduces image signal effects, and makes it a potential candidate for 5G large-scale array applications. To the best of the authors’ knowledge, this is the first article that thoroughly analyzes and implements an FPA with bilateral suppression.
- 5 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Components, Packaging and Manufacturing Technology
- Vol. 16 (2) , 451-454
High Selectivity BPF With Wideband and Stopband Exploiting 3-D CRLH-SIW in Through Glass via (TGV)-Based Package
A high selectivity band-pass filter (BPF) with wide passband and out-of-band suppression based on through glass vias (TGV) technology is presented in this brief. By embedding three-dimensional (3D) composite right-/left-handed (CRLH) structure into the substrate integrated waveguide (SIW) resonator or connecting short-circuit 3D CRLH to feeding lines (FLs), the equivalent dual-CRLH effect is achieved by the parasitic right-handed capacitances between TGVs, leading to high-Q quasi-bound states in the continuum (Q-BIC) and eliminating the need for discrete capacitive and inductive elements. Consequently, four independently adjustable transmission zeros (TZs) are produced at both lower and upper passband, enabling broadband operation, sharp selectivity, and extended stopband suppression. The measured center frequency of the BPF is f0=42.15 GHz with a -3 dB fractional bandwidth (FBW) of 37.3%. The rectangle coefficient of BW-30 dB/BW-3 dB equals 1.41. The out-of-band suppression is better than-20 dB with frequencies more than 110 GHz.
- 5 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Components, Packaging and Manufacturing Technology
- Vol. 16 (2) , 451-454
High Selectivity BPF With Wideband and Stopband Exploiting 3-D CRLH-SIW in Through Glass via (TGV)-Based Package
A high selectivity band-pass filter (BPF) with wide passband and out-of-band suppression based on through glass vias (TGV) technology is presented in this brief. By embedding three-dimensional (3D) composite right-/left-handed (CRLH) structure into the substrate integrated waveguide (SIW) resonator or connecting short-circuit 3D CRLH to feeding lines (FLs), the equivalent dual-CRLH effect is achieved by the parasitic right-handed capacitances between TGVs, leading to high-Q quasi-bound states in the continuum (Q-BIC) and eliminating the need for discrete capacitive and inductive elements. Consequently, four independently adjustable transmission zeros (TZs) are produced at both lower and upper passband, enabling broadband operation, sharp selectivity, and extended stopband suppression. The measured center frequency of the BPF is f0=42.15 GHz with a -3 dB fractional bandwidth (FBW) of 37.3%. The rectangle coefficient of BW-30 dB/BW-3 dB equals 1.41. The out-of-band suppression is better than-20 dB with frequencies more than 110 GHz.
- 30 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 74 (00189456) , 1-10
Post-Bond TSV Defect Detection Circuit Based on a Cross-Coupled Transistor Pair With Positive Feedback Mechanism
In post-bond through-silicon vias (TSVs), existing detection techniques suffer from insufficient defect type coverage, limited detection accuracy, and high sensitivity to process-voltage-temperature (PVT) variations. To address these limitations, this paper proposes a post-bond TSV detection circuit based on a cross-coupled transistor pair with a positive feedback mechanism. The proposed circuit sequentially detects bridge, open, void, and leakage defects by reconfiguring a transmission-gate switch array and a resistor network, utilizing the exponential gain of positive feedback to enable precise discrimination of minute resistance variations. The symmetric topology ensures stability, even under device mismatches and PVT fluctuations. Worst-case PVT corner simulations and Monte Carlo simulations demonstrate that the circuit can reliably detect void defects down to 10 Ω and leakage defects of 4 KΩ within microsecond-scale test durations, with statistical analysis confirming robust performance against process variations. Compared to conventional methods, the proposed design achieves better defect-type coverage, finer discrimination of defect degree, and enhanced immunity to process variations. These results demonstrate the potential of the proposed circuit to improve yield and reliability in 3-D integrated circuits employing TSVs.
- 30 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 74 (00189456) , 1-10
Post-Bond TSV Defect Detection Circuit Based on a Cross-Coupled Transistor Pair With Positive Feedback Mechanism
In post-bond through-silicon vias (TSVs), existing detection techniques suffer from insufficient defect type coverage, limited detection accuracy, and high sensitivity to process-voltage-temperature (PVT) variations. To address these limitations, this paper proposes a post-bond TSV detection circuit based on a cross-coupled transistor pair with a positive feedback mechanism. The proposed circuit sequentially detects bridge, open, void, and leakage defects by reconfiguring a transmission-gate switch array and a resistor network, utilizing the exponential gain of positive feedback to enable precise discrimination of minute resistance variations. The symmetric topology ensures stability, even under device mismatches and PVT fluctuations. Worst-case PVT corner simulations and Monte Carlo simulations demonstrate that the circuit can reliably detect void defects down to 10 Ω and leakage defects of 4 KΩ within microsecond-scale test durations, with statistical analysis confirming robust performance against process variations. Compared to conventional methods, the proposed design achieves better defect-type coverage, finer discrimination of defect degree, and enhanced immunity to process variations. These results demonstrate the potential of the proposed circuit to improve yield and reliability in 3-D integrated circuits employing TSVs.
- 28 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Components, Packaging and Manufacturing Technology
- Vol. 16 (3) , 584-592
Electrical Modeling and Discontinuity Optimization of Truncated Spherical Bump-CTSV Structure
This paper presents an accurate equivalent analytical model to address the discontinuity issues in the interconnect structure composed of bumps and coaxial through-silicon-via (CTSV) for high-frequency applications. Derived from quasi-electromagnetic theory for broad-frequency applicability, this model approximates bumps as a portion truncated irregular sphere accounting for the practical fabricating process. Utilizing a differential approach, the resistance, inductance, and capacitance of this bump geometry are calculated, followed by the derivation of the S-parameters for the entire structure. Validation against EM simulations within 0.1–100 GHz demonstrates good agreement. Furthermore, an optimization strategy based on adjusting the bump dimension is employed to mitigate the impact caused by the discontinuity at the joint. The target function is established according to the impedance matching conditions, and the appropriate radii of the bump are determined to achieve the optimal transmission performance. The results show that S11 and S21 have maximum improvements of 13.70 dB and 1.53dB respectively. The TDR impedance also shows an improvement of 14.13%.
- 28 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Components, Packaging and Manufacturing Technology
- Vol. 16 (3) , 584-592
Electrical Modeling and Discontinuity Optimization of Truncated Spherical Bump-CTSV Structure
This paper presents an accurate equivalent analytical model to address the discontinuity issues in the interconnect structure composed of bumps and coaxial through-silicon-via (CTSV) for high-frequency applications. Derived from quasi-electromagnetic theory for broad-frequency applicability, this model approximates bumps as a portion truncated irregular sphere accounting for the practical fabricating process. Utilizing a differential approach, the resistance, inductance, and capacitance of this bump geometry are calculated, followed by the derivation of the S-parameters for the entire structure. Validation against EM simulations within 0.1–100 GHz demonstrates good agreement. Furthermore, an optimization strategy based on adjusting the bump dimension is employed to mitigate the impact caused by the discontinuity at the joint. The target function is established according to the impedance matching conditions, and the appropriate radii of the bump are determined to achieve the optimal transmission performance. The results show that S11 and S21 have maximum improvements of 13.70 dB and 1.53dB respectively. The TDR impedance also shows an improvement of 14.13%.
- 5 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
- Vol. 33 (4) , 1167-1171
Compact On-Chip Half-Mode SIW-Based Dual-Band Bandpass Filter Using 3-D Stacked Inductors With Controllable Transmission Zero
A compact half-mode substrate-integrated waveguide (HMSIW) dual-band bandpass filter (BPF) is proposed based on the through silicon vias (TSVs) technology in this brief. The two pass bands of the filter operating at 14.02 and 21.46 GHz with the 3-dB fractional bandwidth (FBW) of 32.2% and 27.5% are constructed by the quasi-TEM and TE102 modes, respectively. 3-D-stacked inductors utilizing TSVs and redistribution layers (RDLs) are employed to induce mixed couplings, thereby generating a transmission zero (TZ) above the passband, which are analyzed by the equivalent circuit of the filter. The circuit size of the fabricated prototype of the dual-band HMSIW BPF is $0.18\lambda _{g}^{2}$ . The in-band insertion losses (ILs) are 1.37 and 1.33 dB, severally. Measurement results agree well with the electromagnetic (EM) simulation results.
- 5 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
- Vol. 33 (4) , 1167-1171
Compact On-Chip Half-Mode SIW-Based Dual-Band Bandpass Filter Using 3-D Stacked Inductors With Controllable Transmission Zero
A compact half-mode substrate-integrated waveguide (HMSIW) dual-band bandpass filter (BPF) is proposed based on the through silicon vias (TSVs) technology in this brief. The two pass bands of the filter operating at 14.02 and 21.46 GHz with the 3-dB fractional bandwidth (FBW) of 32.2% and 27.5% are constructed by the quasi-TEM and TE102 modes, respectively. 3-D-stacked inductors utilizing TSVs and redistribution layers (RDLs) are employed to induce mixed couplings, thereby generating a transmission zero (TZ) above the passband, which are analyzed by the equivalent circuit of the filter. The circuit size of the fabricated prototype of the dual-band HMSIW BPF is $0.18\lambda _{g}^{2}$ . The in-band insertion losses (ILs) are 1.37 and 1.33 dB, severally. Measurement results agree well with the electromagnetic (EM) simulation results.
- 27 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 24 (14) , 22758-22763
A New Low Profile Differential Magnetic Probe With Enhanced Sensitivity
In this work, a new differential magnetic probe with a low profile and high sensitivity is showcased. Firstly, a traditional U-shaped differential loop as a driving component is developed to test the magnetic field component. Secondly, two pairs of grounded U-shaped loops as parasitic components are placed on both sides of the U-shaped loop to enhance detection sensitivity in this proposed probe. Owing to these grounded U-shaped loops being able to test more magnetic field energy, the proposed differential magnetic probe has a high sensitivity. In addition, unlike traditional parasitic loops placed on the inner layers of the probe, a pair of grounded U-shaped loops and these ground planes are arranged at the outer layers of the differential magnetic probe, which can effectively reduce the probe’s profile. Based on this clever design, the presented differential magnetic probe only requires a five-layer PCB for processing rather than a seven-layer PCB. As a result, the designed probe is etched, simulated, and tested to verify its effectiveness. A near-field scanning measurement system with a standard microstrip line is used to characterize the presented differential magnetic probe. Measured results reveal that the presented differential magnetic probe not only has a high sensitivity, but also has a low profile.
- 27 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 24 (14) , 22758-22763
A New Low Profile Differential Magnetic Probe With Enhanced Sensitivity
In this work, a new differential magnetic probe with a low profile and high sensitivity is showcased. Firstly, a traditional U-shaped differential loop as a driving component is developed to test the magnetic field component. Secondly, two pairs of grounded U-shaped loops as parasitic components are placed on both sides of the U-shaped loop to enhance detection sensitivity in this proposed probe. Owing to these grounded U-shaped loops being able to test more magnetic field energy, the proposed differential magnetic probe has a high sensitivity. In addition, unlike traditional parasitic loops placed on the inner layers of the probe, a pair of grounded U-shaped loops and these ground planes are arranged at the outer layers of the differential magnetic probe, which can effectively reduce the probe’s profile. Based on this clever design, the presented differential magnetic probe only requires a five-layer PCB for processing rather than a seven-layer PCB. As a result, the designed probe is etched, simulated, and tested to verify its effectiveness. A near-field scanning measurement system with a standard microstrip line is used to characterize the presented differential magnetic probe. Measured results reveal that the presented differential magnetic probe not only has a high sensitivity, but also has a low profile.