Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Laura Oropeza-Ramos has a total of 82 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Scalable Ni-Based Diffusion Synthesis of Highly Graphitic Nanointerlaced and Photopatternable Material with Fast Charge Transfer Kinetics

    by Carina Chávez-Granados, Pedro Roquero, Oscar Pilloni, Margarita Rivera, Marc J. Madou, Laura Oropeza-Ramos

    Graphitic and nanostructured carbon materials exhibit exceptional properties, including high electrical conductivity and chemical stability, yet their integration into microdevices remains challenging due to costly, low-yield production methods. Carbon-MEMS (C-MEMS) technology offers a scalable alternative for fabricating carbon microdevices, though it typically yields amorphous/glassy carbon with limited conductivity. Here, we bridge this gap with a scalable method for synthesizing highly conductive graphitic micropatterns. Our approach combines electrospinning of a photosensitive SU-8/MWCNT composite with pyrolysis and catalytic graphitization using a Ni film. Raman spectroscopy confirms increased graphitization (ID/IG = 0.3 vs 0.92 for pyrolytic carbon), and HRTEM analysis reveals numerous graphitic domains with parallel lattices exhibiting an interlayer distance of 3.46–3.59 Å. These observations are consistent with the substantial decrease in the ID/IG ratio and the corresponding increase in crystallite size (La) estimated by Raman spectroscopy, confirming the evolution of disordered carbon toward a long-range preferred orientation. This structural transformation is promoted by the Ni-based diffusion mechanism specific to our porous architecture. The process results in carbon nanofiber mats with enhanced electrical conductivity (CI95% [615.0, 824.2] S/m), a significant improvement over pyrolytic mats from the same composite (CI95% [4638.1, 5625.9] S/m). Electrochemically, the material exhibits superior charge-transfer kinetics (k° = 0.064 cm/s), outperforming some conventional carbons. Our investigations reveal that the inclusion of MWCNTs reduces porosity, thereby increasing conductivity by 3 orders of magnitude, which allows for the surface area and electron-transfer tuning. Furthermore, our Ni-based diffusion synthesis enables the direct integration of micropatterned, nanointerlaced graphitic devices into silicon substrates, eliminating transfer steps or the need for mechanical treatment while enabling complex geometries. In summary, this work provides a large-scalable route for the next generation of high-performance graphitic devices with broad applicability in miniaturized sensors and energy systems.

  • Open Access

    Design and validation of an instrumented electrospinning system for nanofiber deposition on semiconducting substrates: A case study using SU-8 and CNT/SU-8 composites

    by Dulce K. Becerra-Paniagua, Rolando Rubio, Sveidy Vaca, Laura Oropeza-Ramos, Oscar Pilloni

    Electrospinning enables the fabrication of polymer nanofibers with tunable morphological and functional properties; however, its application to semiconducting substrates presents technical challenges due to limited control over deposition parameters and poor charge dissipation. In this work, we report the design, instrumentation, and validation of a custom electrospinning system developed to address these challenges. The system integrates modular hardware and software components for precise, reproducible control over applied voltage, flow rate, and needle-to-collector distance. Environmental conditions (temperature and humidity) are also monitored in real time to improve consistency in fiber formation. To evaluate system performance, we employed a novolac-based epoxy photoresist (SU-8) and carbon nanotube-reinforced SU-8 (CNT/SU-8) composite solutions as case study materials, both known for their electrospinning difficulty yet offering high relevance for microfabrication applications. Process optimization enabled the direct deposition of uniform nanofiber mats on silicon substrates, eliminating transfer steps and reducing contamination risks. Additives such as poly(ethylene oxide) (PEO) and tri-tert-butylphosphonium tetrafluoroborate (BF₄) further improved fiber uniformity and mat density. Comprehensive characterization was conducted to validate deposition quality and post-processing outcomes. Scanning electron microscopy (SEM) and Raman spectroscopy were used to assess nanofiber morphology, mat coverage, and microstructure, while rheological analysis quantified the viscoelastic properties of the precursor solutions. This instrumented electrospinning platform offers a reproducible and scalable route for nanofiber integration in carbon-based microdevices. Its modular and compact design makes it well suited for research environments focused on Carbon Microelectromechanical Systems (C-MEMS), biomedical devices, and microscale energy storage technologies, expanding the capabilities of electrospinning in advanced manufacturing.


  • Open Access

    Critical aspects of droplet digital reverse transcription loop-mediated isothermal amplification (ddRT-LAMP) for viral pathogens detection

    by Kenia Chávez-Ramos, Frida Trejo, Prisciluis Caheri Salas-Navarrete, Eva Ramón-Gallegos, José Esteban Muñoz-Medina, Luis Alvarez-Icaza, Luis F. Olguin, Oscar Pilloni, Laura Oropeza-Ramos

    The COVID-19 pandemic evidenced the urgent need for rapid, accurate, and scalable diagnostic methods for emerging infectious diseases. Droplet digital reverse transcription LAMP (ddRT-LAMP) is a promising technique for pathogen detection and accurate quantification, as it overcomes traditional LAMP’s limitations in viral load estimation through reaction partitioning and digital analysis. However, many parameters must be adjusted to avoid spurious results. This study evaluates the critical conditions for effective ddRT-LAMP quantification of the SARS-CoV-2 N gene in plasmid DNA, synthetic RNA, and nasopharyngeal swab samples. Using a polydimethylsiloxane (PDMS) microfluidic device, the RT-LAMP reaction mixture with a fluorescent dye was divided into thousands of droplets stabilized by a surfactant in fluorinated oil. After incubation, the droplets were injected into a PDMS chamber for fluorescent imaging to determine the proportion of positive droplets and quantify the samples based on the Poisson distribution. The results showed that primer design and master mix composition significantly impacted the amplification. The selection of GelGreen® as the fluorescent dye was crucial, as other dyes tested diffused into the oil phase. Optimal amplification occurred with 105 µm droplet diameter and 30-min incubation, achieving detection and quantification limits of 102 cp/µL. By addressing these operational challenges, ddRT-LAMP can become a more effective tool for viral detection and quantification in clinical diagnostics.


  • Open Access

    Critical aspects of droplet digital reverse transcription loop-mediated isothermal amplification (ddRT-LAMP) for viral pathogens detection

    by Laura Oropeza-Ramos, Oscar Pilloni, Luis Olguin, Kenia Chávez-Ramos, Frida Trejo, Prisciluis Salas-Navarrete, Eva Ramón-Gallegos, José Muñoz-Medina, Luis Álvarez-Icaza

    The COVID-19 pandemic evidenced the urgent need for rapid, accurate, and scalable diagnostic methods for emerging infectious diseases. Droplet digital reverse transcription loop-mediated isothermal amplification (ddRT-LAMP) is a promising technique for pathogen detection and DNA or RNA quantification. Compared to ddPCR, it simplifies device design, reduces power consumption and analysis time, and enhances compatibility with miniaturization, making it ideal for portable, high-throughput nucleic acid detection applications. However, many parameters must be adjusted according to the application to avoid spurious results. This study critically examines key conditions for an effective ddRT-LAMP assay to quantify copies of SARS-CoV-2 N gene coded in plasmid DNA, synthetic viral RNA, or patients’ nasopharyngeal swab samples. Using a polydimethylsiloxane (PDMS) microfluidic device, the RT-LAMP reaction mixture with a fluorescent dye was divided into thousands of droplets stabilized by a surfactant in fluorinated oil. After incubation, the droplets were injected into a PDMS chamber for fluorescent imaging to determine the proportion of positive droplets and quantify the samples based on Poisson distribution. Samples with viral loads up to 102 copies/µL were quantified with high precision. Results showed that primer design and master mix composition significantly impacted the amplification. Selection of GelGreen® as the fluorescent dye was crucial, as other dyes tested diffused into the oil phase. Droplets with a diameter of around 105 µm and an incubation time of 30 min were required to achieve maximum amplification. By addressing these operational challenges, ddRT-LAMP can become a more effective tool for viral detection and quantification in clinical diagnostics.

  • Open Access

    Droplet impact outcomes of emulsions on smooth and microstructured surfaces

    by Miguel A. Quetzeri-Santiago, Laura Oropeza-Ramos, Francisco Manuel Sánchez-Arévalo

    This study explores the impact dynamics of emulsion droplets, with a dispersed phase of either silicone oil, toluene, or heptane, and water as the continuous phase, on both smooth and microstructured surfaces fabricated via photolithography. By preparing emulsions without surfactants, we isolated the effects of surface morphology and liquid properties on droplet behavior. We characterized the rheology of the emulsions and their droplet size distributions. The impact dynamics were recorded using a high-speed camera in a shadowgraph configuration, with analysis performed through image processing techniques. Our results indicate that at higher impact velocities, water exhibits the largest spreading diameter (dmax) on smooth surfaces, while emulsions with higher dispersed phase concentrations show reduced spreading due to increased energy dissipation. On microstructured surfaces, denser structures enhance resistance to spreading and trigger complex phenomena such as Worthington jets and secondary droplets, which are not observed on smooth surfaces. Additionally, we observed a transition in bouncing behavior for the silicone oil 50 cSt 20 v/v% emulsion on Glaco-coated surfaces, attributed to the infiltration of silicone oil into the Glaco microstructure, creating a suction force that prevents bouncing. These findings offer valuable insights for optimizing industrial processes like inkjet printing and pesticide application, where precise control of droplet behavior is crucial.

  • Open Access

    Beyond two dimensions: Exploring 3D dielectrophoresis for microparticle control using carbon electrodes

    by Oscar Pilloni, Marc Madou, Laura Oropeza-Ramos

    This study explores the frontiers of microparticle manipulation by introducing an actuator platform for the three-dimensional positioning of microparticles using dielectrophoresis (DEP), a technique known for its selectivity and ease of integration with microtechnology. Leveraging advancements in carbon-based devices due to their biocompatibility and electrochemical stability, our work extends the application of DEP from two-dimensional constraints to precise 3D positioning within microvolumes, employing a photolithography-based fabrication process known as Carbon-MEMS technology (C-MEMS). We present the design, finite element simulation, fabrication, and testing of this platform, which utilizes a unique combination of planar and 3D carbon microelectrodes individually addressable on a transparent substrate. This setup enables the application of DEP forces, allowing for high-throughput manipulation of multiple microparticles simultaneously, as well as displacement of individual microparticles in any desired direction. Demonstrated with spherical 1μm and 10μm diameter polystyrene microparticles, this platform features straightforward fabrication and is suitable for batch industrial production. The study concludes with a discussion of the platform’s advantages and limitations, marking a significant step toward a valuable tool for studying complex biological systems.


  • Open Access

    El gran mundo de la tecnología miniatura

    by Dulce Kristal Becerra-Paniagua, Carina Chávez-Granados, Laura Oropeza-Ramos

    Muchos de nosotros hemos escuchado la palabra microtecnología quizá en anuncios publicitarios de ropa, cosméticos, alimentos, electrdomésticos, medicamentos, entre otros. El prefijo micro proviene del vocablo griegos “μικρός” (mikros) que significa pequeño, por lo tanto, su concepto se refiere a la tecnología que nos permite construir sensores, actuadores y electrónica con elementos que están en el límite de lo que podemos ver a simple vista.

  • Open Access

    Electrical performance enhancement of MHD microgenerators through the longitudinal shaping of the cross-section

    by F. Trillaud, J.E.V. Guzmán, M.A. Ramírez-Trocherie, L. Oropeza-Ramos

  • Comparative genomic analysis of Mycoplasma related to cell culture for infB gene-based loop-mediated isothermal amplification

    by Benjamín Luna-Callejas, Laura Oropeza-Ramos, Eva Ramón-Gallegos

    Mycoplasma contamination in cell culture affects the properties of cell lines. Gold standard detection by microbiological culture takes days and requires specialists. The polymerase chain reaction and loop-mediated isothermal amplification (LAMP) are fast molecular options, but LAMP only requires one heating block for DNA amplification. This study presents a comparative genomic analysis of Mycoplasma species to identify common target genes different from the rrsA gene, which encodes 16 S rRNA. The aim is to implement a LAMP assay to detect Mycoplasma species, reducing the time and specialized equipment required for detection. We performed a comparative genomic analysis through Mauve software and the GView server and selected infB and clpB genes as target candidates for designing LAMP primers. We evaluated both genes by multiple sequence alignment (MSA). The infB gene presented the best score MSA assessment with lower odd-log values (5,480,281) than other genes. We selected the infB gene to design LAMP primers specific to Mycoplasma spp. We used these primers to implement LAMP at 63 °C for 30 min, which showed 100% positive amplifications for detecting Mycoplasma spp. In conclusion, we present a methodology utilizing the infB gene-based LAMP assay to detect three of the six most prevalent Mycoplasma species in cell culture. Graphical abstract

  • Photolithographically-patterned C-MEMS graphene by carbon diffusion through nickel

    by Sveidy Vaca, Oscar Pilloni, Axel Rodríguez Gómez, Laura N Serkovic-Loli, Naser Qureshi, Laura Oropeza-Ramos

    In recent years the most studied carbon allotrope has been graphene, due to the outstanding properties that this two-dimensional material exhibits; however, it turns out to be a difficult material to produce, pattern, and transfer to a device substrate without contamination. Carbon microelectromechanical systems are a versatile technology used to create nano/micro carbon devices by pyrolyzing a patterned photoresist, making them highly attractive for industrial applications. Furthermore, recent works have reported that pyrolytic carbon material can be graphitized by the diffusion of carbon atoms through a transition metal layer. In this work we take advantage of the latter two methods in order to produce multilayer graphene by improving the molecular ordering of photolithographically-defined pyrolytic carbon microstructures, through the diffusion (annealing) of carbon atoms through nickel, and also to eliminate any further transfer process to a device substrate. The allotropic nature of the final carbon microstructures was inspected by Raman spectroscopy (Average I D / I G of 0.2348 ± 0.0314) and TEM clearly shows well-aligned lattice planes of 3.34 Å fringe separation. These results were compared to measurements made on pyrolytic carbon (Average I D / I G of 0.9848 ± 0.0235) to confirm that our method is capable of producing a patterned multilayer graphene material directly on a silicon substrate.