Beizhi Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Beizhi Li has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
Weicheng Guo
College of Mechanical Engineering, Donghua University, Shanghai, China
8 shared publicationsQinzhi Zhou
College of Mechanical Engineering, Donghua University, Shanghai, China
6 shared publicationsShouguo Shen
College of Mechanical Engineering, Donghua University, Shanghai, China
4 shared publicationsWanjiao Dong
College of Mechanical Engineering, Donghua University, Shanghai, China
3 shared publications- Yao Liu
School of Mechanical Engineering, North University of China, Taiyuan 030051, China
3 shared publications - Chongjun Wu
Donghua University, Shanghai, China
2 shared publications
Latest Publications
- 17 August 2022
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 122 (2) , 835-847
Subsurface residual stress and damaged layer in high-speed grinding considering thermo-mechanical coupling influence
- 17 August 2022
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 122 (2) , 835-847
Subsurface residual stress and damaged layer in high-speed grinding considering thermo-mechanical coupling influence
- 17 February 2020
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 107 (1-2) , 535-547
Prediction of different design conditions on comprehensive performance of hydrostatic slide and experimental verification
- 17 February 2020
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 107 (1-2) , 535-547
Prediction of different design conditions on comprehensive performance of hydrostatic slide and experimental verification
- 2 December 2019
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 106 (3-4) , 953-967
Experimental study on grinding-induced residual stress in C-250 maraging steel
- 2 December 2019
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 106 (3-4) , 953-967
Experimental study on grinding-induced residual stress in C-250 maraging steel
- Open Access
- 1 September 2019
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 626 (1) , 012005
Optimization Design Method for Hydrostatic Guideway Based on PM Restrictor
Stiffness and flow rate are always used to evaluate the performance of the hydrostatic slides and well-designed parameters, such as flow rate ratio, initial flow rate, pump pressure and oil film thickness, allow the slides achieving nanoscale precision. In this study, the relationship between the design parameters and the stiffness and flow rate is reveal by an analytical model. Then a multi-objective optimization problem is solved using Non-dominated Sorting Genetic Algorithm II. The optimization objectives are maximize stiffness and minimize flow rate. At last, the optimized design parameters are calculated and corresponding maximum stiffness and minimum flow rate of the hydrostatic slides are acquired.
- 1 September 2019
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 626 (1) , 012005
Open AccessOptimization Design Method for Hydrostatic Guideway Based on PM Restrictor
Stiffness and flow rate are always used to evaluate the performance of the hydrostatic slides and well-designed parameters, such as flow rate ratio, initial flow rate, pump pressure and oil film thickness, allow the slides achieving nanoscale precision. In this study, the relationship between the design parameters and the stiffness and flow rate is reveal by an analytical model. Then a multi-objective optimization problem is solved using Non-dominated Sorting Genetic Algorithm II. The optimization objectives are maximize stiffness and minimize flow rate. At last, the optimized design parameters are calculated and corresponding maximum stiffness and minimum flow rate of the hydrostatic slides are acquired.
- 6 August 2019
- Published by Taylor & Francis in Tribology Transactions
- Vol. 62 (6) , 1142-1154
Deformation Analysis of Hydrostatic Guideways Based on the Cantilever Plate Bending Calculation Method
In this study, a novel analytical model considering practical oil pressure and a cantilever plate bending calculation method is proposed to calculate the deformation of a vertical hydrostatic guideway. Based on the governing equations of rectangular thin plates, the finite integral transformation theory and the series-by-item differential transformation theory are used to solve the bending deformation of the target guideway to avoid the errors caused by an artificially selected deflection function and Kirchhoff’s hypothesis. The deformation values obtained from finite element simulation and experiments are compared with those calculated from the model. The comparison results show that the proposed model is capable of providing deformation values that are in better agreement with the experimental values than simulation values and its computation time is much less than that of the finite element method. The quantitative relationship between the actual oil film thickness and the performance of the hydrostatic guideways considering the size effect of the oil film thickness is studied.
- 6 August 2019
- Published by Taylor & Francis in Tribology Transactions
- Vol. 62 (6) , 1142-1154
Deformation Analysis of Hydrostatic Guideways Based on the Cantilever Plate Bending Calculation Method
In this study, a novel analytical model considering practical oil pressure and a cantilever plate bending calculation method is proposed to calculate the deformation of a vertical hydrostatic guideway. Based on the governing equations of rectangular thin plates, the finite integral transformation theory and the series-by-item differential transformation theory are used to solve the bending deformation of the target guideway to avoid the errors caused by an artificially selected deflection function and Kirchhoff’s hypothesis. The deformation values obtained from finite element simulation and experiments are compared with those calculated from the model. The comparison results show that the proposed model is capable of providing deformation values that are in better agreement with the experimental values than simulation values and its computation time is much less than that of the finite element method. The quantitative relationship between the actual oil film thickness and the performance of the hydrostatic guideways considering the size effect of the oil film thickness is studied.
- 29 April 2019
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 103 (5-8) , 2837-2847
An intelligent grinding burn detection system based on two-stage feature selection and stacked sparse autoencoder
- 29 April 2019
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 103 (5-8) , 2837-2847
An intelligent grinding burn detection system based on two-stage feature selection and stacked sparse autoencoder
- 5 April 2019
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture
- Vol. 233 (13) , 2436-2446
An intelligent monitoring system of grinding wheel wear based on two-stage feature selection and Long Short-Term Memory network
Grinding wheel condition is considered as the key factor affecting grinding performance, and therefore, accurate monitoring of wheel wear is necessary to prevent the deterioration of part quality. An intelligent wheel wear monitoring system is introduced in this article to realize processing of grinding signal, extraction of signal features, selection of optimal feature subset, and prediction of wheel wear. Physical information generated during the grinding of C-250 maraging steel is collected by a dynamometer, accelerometer, and acoustic emission sensor, and a large quantity of features in time domain and frequency domain are extracted from the processed grinding signals. To reduce feature redundancy and increase relevancy of feature to wheel wear, a two-stage feature selection approach combining filter and wrapper framework is proposed. The filter preselects individual features by minimum Redundancy Maximum Relevance method, while the wrapper evaluates different feature subsets by the model performance. A deep learning network structure named Long Short-Term Memory network is adopted to develop the wheel wear monitoring model and is compared with a conventional machine learning algorithm, Random Forest. The results have shown that the two-stage feature selection method is able to provide the globally optimal feature subset for the model. Long Short-Term Memory model achieves an R2 of 0.994 and a root-mean-square error of 0.240 with four features, while Random Forest model obtains an R2 of 0.980 and a root-mean-square error of 0.463 with seven features, which indicates that Long Short-Term Memory model is capable of predicting wheel wear more accurately even with less features.
- 5 April 2019
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture
- Vol. 233 (13) , 2436-2446
An intelligent monitoring system of grinding wheel wear based on two-stage feature selection and Long Short-Term Memory network
Grinding wheel condition is considered as the key factor affecting grinding performance, and therefore, accurate monitoring of wheel wear is necessary to prevent the deterioration of part quality. An intelligent wheel wear monitoring system is introduced in this article to realize processing of grinding signal, extraction of signal features, selection of optimal feature subset, and prediction of wheel wear. Physical information generated during the grinding of C-250 maraging steel is collected by a dynamometer, accelerometer, and acoustic emission sensor, and a large quantity of features in time domain and frequency domain are extracted from the processed grinding signals. To reduce feature redundancy and increase relevancy of feature to wheel wear, a two-stage feature selection approach combining filter and wrapper framework is proposed. The filter preselects individual features by minimum Redundancy Maximum Relevance method, while the wrapper evaluates different feature subsets by the model performance. A deep learning network structure named Long Short-Term Memory network is adopted to develop the wheel wear monitoring model and is compared with a conventional machine learning algorithm, Random Forest. The results have shown that the two-stage feature selection method is able to provide the globally optimal feature subset for the model. Long Short-Term Memory model achieves an R2 of 0.994 and a root-mean-square error of 0.240 with four features, while Random Forest model obtains an R2 of 0.980 and a root-mean-square error of 0.463 with seven features, which indicates that Long Short-Term Memory model is capable of predicting wheel wear more accurately even with less features.
- 30 March 2019
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 103 (1-4) , 1079-1094
Surface integrity in grinding of C-250 maraging steel with resin-bonded and electroplated CBN grinding wheels
- 30 March 2019
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 103 (1-4) , 1079-1094
Surface integrity in grinding of C-250 maraging steel with resin-bonded and electroplated CBN grinding wheels
- 10 December 2018
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 233 (10) , 3475-3486
Experimental study on force model in grinding of maraging steel 3J33
Grinding is always a complicated machining process for joint interaction of numerous random abrasive grits in different chip formation processes. Therefore, analysis of grinding force requires a more comprehensive insight on the grinding mechanisms. This paper is devoted to propose an analytical force model in grinding of maraging steel 3J33 based on the fact that grinding process is divided into three stages, namely rubbing, ploughing and cutting, in terms of grits working status. These three stages are determined by the chip thickness model that is assumed to conform to Rayleigh distribution, in which the rubbing stage is derived from Hertzian contact theory. The experimental coefficients in the force model are calibrated by performing a set of training tests. The predicted normal and tangential grinding forces of the developed model are compared with those obtained from validation tests, which show favorable agreement quantitatively. The contributions of the grinding force components in different grit–workpiece interaction stages are obtained from the model and theirs relationships with process parameters are discussed.
- 10 December 2018
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 233 (10) , 3475-3486
Experimental study on force model in grinding of maraging steel 3J33
Grinding is always a complicated machining process for joint interaction of numerous random abrasive grits in different chip formation processes. Therefore, analysis of grinding force requires a more comprehensive insight on the grinding mechanisms. This paper is devoted to propose an analytical force model in grinding of maraging steel 3J33 based on the fact that grinding process is divided into three stages, namely rubbing, ploughing and cutting, in terms of grits working status. These three stages are determined by the chip thickness model that is assumed to conform to Rayleigh distribution, in which the rubbing stage is derived from Hertzian contact theory. The experimental coefficients in the force model are calibrated by performing a set of training tests. The predicted normal and tangential grinding forces of the developed model are compared with those obtained from validation tests, which show favorable agreement quantitatively. The contributions of the grinding force components in different grit–workpiece interaction stages are obtained from the model and theirs relationships with process parameters are discussed.
- 7 December 2018
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture
- Vol. 233 (10) , 2047-2060
Heat flux distribution and temperature prediction model for dry and wet cylindrical plunge grinding
The grinding heat is generally partitioned into the workpiece, wheel, chips and fluid in grinding process. The total amount of heat flux entering into the workpiece greatly affects the final workpiece surface temperature, which may cause undesirable workpiece burn. Moreover, the variable grinding chip thickness and fluid injection speed along the grinding contact zone could substantially change the specific energy and the shape of the heat source correspondingly. In this article, a Weibull heat flux distribution model for both dry and wet grinding temperature prediction was proposed by analyzing two key parameters: energy partition Rw and shape parameter k. The value of Rw was obtained by considering the real contact length, the active grits number and the average grit radius r0 on the basis of traditional formulas. The relationship between shape parameters k and useful flow was established by a FLUENT simulation of the convective grinding fluid applied in grinding contact zone with wheel-workpiece minimum clearance. The grinding temperature and grinding force experiments were conducted on a grinding machine MGKS1332/H to validate the proposed heat flux model. The calculated workpiece surface temperature distribution was obtained by using the experimental heat flux obtained by the reverse algorithm, and the error between calculated temperature and experimental temperature was analyzed. With the monitored force signals and the proposed temperature prediction model, the grinding temperature for both dry and wet grinding can be predicted, which will be helpful to the optimization and control of temperature in grinding process.
- 7 December 2018
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture
- Vol. 233 (10) , 2047-2060
Heat flux distribution and temperature prediction model for dry and wet cylindrical plunge grinding
The grinding heat is generally partitioned into the workpiece, wheel, chips and fluid in grinding process. The total amount of heat flux entering into the workpiece greatly affects the final workpiece surface temperature, which may cause undesirable workpiece burn. Moreover, the variable grinding chip thickness and fluid injection speed along the grinding contact zone could substantially change the specific energy and the shape of the heat source correspondingly. In this article, a Weibull heat flux distribution model for both dry and wet grinding temperature prediction was proposed by analyzing two key parameters: energy partition Rw and shape parameter k. The value of Rw was obtained by considering the real contact length, the active grits number and the average grit radius r0 on the basis of traditional formulas. The relationship between shape parameters k and useful flow was established by a FLUENT simulation of the convective grinding fluid applied in grinding contact zone with wheel-workpiece minimum clearance. The grinding temperature and grinding force experiments were conducted on a grinding machine MGKS1332/H to validate the proposed heat flux model. The calculated workpiece surface temperature distribution was obtained by using the experimental heat flux obtained by the reverse algorithm, and the error between calculated temperature and experimental temperature was analyzed. With the monitored force signals and the proposed temperature prediction model, the grinding temperature for both dry and wet grinding can be predicted, which will be helpful to the optimization and control of temperature in grinding process.