AGAlexandra M. Golobic

Alexandra M. Golobic

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Alexandra M. Golobic has a total of 41 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Modeling direct ink-writing of a sinusoid using a sharp-interface method

    by Alec Kucala, Alexandra Golobic, Rekha Rao, Todd Weisgraber, David Noble

    Direct ink writing (DIW) is an additive manufacturing technique used to fabricate complex structures by depositing viscous material onto a substrate. Our particular application requires printing of sinusoidal shapes of constant amplitude and thickness. These experimentally printed paths, which uses G-code motion commands that are interpreted by the Aerotech A3200 motion controller, show significant errors between the desired printing amplitudes and the actual deposited amplitudes. To clarify these discrepancies, we use a Galerkin finite element model (GFEM) that incorporates the Streamline Upwind/Petrov-Galerkin (SUPG) method and employs the conformal decomposition finite element method (CDFEM) to dynamically discretize the moving ink/air interface. This interface is tracked using a level set method. Using the motion controller's tracking position and velocity data as inputs to the finite element model, we observe a close match to the experimental amplitudes and thicknesses, showing similar discrepancies observed in the experiments. For a constant printing speed, increasing the ratio between the expected amplitude and nozzle diameter ($A_{m}/D$) shows a significant reduction in the observed amplitude errors. In conjunction with changing this ratio, increasing the desired wavelength of the printed pattern ($\lambda_x$) can also reduce the error in printing amplitude, resulting in as little as 5\% error. The effect of nozzle drop height and injection velocity were also studied in their relationship to the amplitude errors, but we found no correlation with these parameters to minimizing them. However, we did observe that the thickness of the printed sine wave was affected by changing these printing parameters. Finally, a comparison was made between using a Newtonian and non-Newtonian (Casson) viscosity in the finite element model and it was observed that the cross-sectional profiles differed between the two models. However, the amplitudes, wavelengths, and deposited thicknesses were nearly identical, suggesting that a highly-viscous Newtonian viscosity was sufficient in capturing the quantities of interest in this particular study.

  • Novel Fast Cure Silicone Inks for Single‐Step, Support‐Free 3D Printing of Tall, Overhanging, and High Aspect Ratio Structures

    by Anna Guell Izard, Lemuel X. Pérez Pérez, Todd H. Weisgraber, Ilse M. Van Meerbeek, Alexandra M. Golobic, Eric B. Duoss, Jeremy M. Lenhardt

    Silicone elastomers have a broad variety of applications, such as soft robotics, biomedical devices, and structural metamaterials. The extrusion‐based method known as direct ink write (DIW) has enabled the production of additively manufactured silicone structures. However, this method is limited to manufacturing mostly planar or pseudo‐3D structures. Due to the low self‐supporting capabilities of extruded strands for traditional silicone‐based “inks,” obtaining tall or overhanging structures, or structures comprised by thin walls is not feasible. Here, a novel Fast Cure silicone‐based ink is demonstrated that enables manufacturing of complex 3D structures. The Fast Cure ink is a two‐part mixture and silicone structures are produced by inline mixing and coextrusion of a part containing a catalyst (part A) and a part containing a crosslinker (part B). By the virtue of crosslinking, the extruded strands rapidly rigidize, increasing their self‐supportive capacity. Hence, structures can be obtained with superior shape retention and previously unobtainable parts are realized that are tall, with aspect ratios higher than 3, and have overhanging features, achieving inclination angles smaller than 35° with respect to the printing plane. These minimal sag parts are achieved without requiring extra curing or mechanisms, support structures, or suspension baths.


  • Controlled In Situ Foaming for Mechanical Responsiveness of Architected Foams

    by Alexandra M. Golobic, Taylor M. Bryson, Todd H. Weisgraber, Jeremy A. Armas, Eric B. Duoss, Thomas S. Wilson, Jeremy M. Lenhardt

    Addition of chemical blowing agents to polysiloxane resins produces foams with closed‐cell morphology. Combining this chemistry with the 3D‐printing technique direct ink writing (DIW) permits the creation of architected foams with controllable, hierarchical tiers of porosity. Using a two‐component foaming ink, the extent of foaming can be controlled by incorporating an active mixing printhead as part of the fabrication process. Changes in the mixing speed allows for in situ control of the foaming reaction where the mixing speed is directly correlated with the resulting foaming that occurs upon extrusion. These architected foams display tunable mechanical responses, porosities, and open‐to‐closed cell ratios. While chemically blown polysiloxane foam is a well‐established material, utilizing DIW as fabrication technique presents a novel approach for creating tailored, architected foams that require minimal post‐processing.


  • Open Access

    Development of the Multi-Material Inspection for Closed-Loop Rapid Optimization (MICRO) Sensor for Extrusion-Based Additive Manufacturing of Metal-Polymer Composite Inks

    by Jenny Wang, Allan S. P. Chang, Steven L. Hunter, Alexandra M. Golobic, Sarai N. Sherfield, Jeremy M. Lenhardt, Eric B. Duoss, Manyalibo J. Matthews

    Additive Manufacturing (AM), or 3D printing, is a powerful technology that is revolutionizing the way designers create products across many industries. AM technology is severely limited by the lack of effective methods for in situ characterization of multi-material properties and composition during printing. The ability to detect the composition of multi-material printed inks in real time is an emerging need for a wide range of manufacturing applications. In this study, dielectric properties of embedded metal microparticles in a dielectric matrix are measured and characterized as a function of particle size, shape, volume percentage and frequency. Unexpectedly, there was no observation of any percolation threshold. The impedance was found to decrease with the percentage of metal filler as expected. While particle shape seemed to have significant effect on the impedance, there was little to no correlation between particle size and impedance. The resulting data can be used to generate a calibration curve correlating metal loading with impedance or capacitance. We discuss how this data can be used for in situ sensing of local ink composition, which does not currently exist, to facilitate greater control over the resulting properties and functionality of printed materials.


  • 3D Printing of Compositional Gradients Using the Microfluidic Circuit Analogy

    by Du T. Nguyen, Timothy D. Yee, Nikola A. Dudukovic, Koroush Sasan, Adam W. Jaycox, Alexandra M. Golobic, Eric B. Duoss, Rebecca Dylla‐Spears

    3D printing of structures with compositional gradients requires accurate dispensing control to achieve desired profiles. Here, empirical data are used with a model based on the microfluidic circuit analogy (MCA) to project dispense rate profiles that yield improved compositional accuracy in the printed part. Since minor variation in the experimental setup for each printing session can result in significant changes, a calibration procedure is developed to measure the system response. This calibration enables the extraction of the empirical MCA model parameters specific to each print session. Using the empirical parameters, the MCA model then can be used to predict appropriate dispense rates for the desired composition profile and toolpath of interest. The MCA model is validated experimentally by direct ink write 3D printing of compositional gradients using viscoelastic polydimethylsiloxane inks and is shown to improve accuracy to desired profile by a factor of 2–5. This approach enables a new route to 3D print structures with arbitrarily complex compositional gradients.


  • Active Mixing of Reactive Materials for 3D Printing

    by Alexandra M. Golobic, Matthew D. Durban, Scott E. Fisher, Michael D. Grapes, Jason M. Ortega, Christopher M. Spadaccini, Eric B. Duoss, Alexander E. Gash, Kyle T. Sullivan

    The mixing of materials during additive manufacturing is a major benefit which allows one to compositionally and spatially tailor material properties, for example to locally control the reactivity in fuel–oxidizer systems known as thermites. This work characterizes an active mixing printhead used in conjunction with a 3D printing process known as Direct Ink Writing. Besides compositional control, a major benefit of this approach is that it offers a safe method for working with these materials, which can otherwise be hazardous once mixed. Custom fuel and oxidizer inks are fed at fixed volumetric rates into an active mixing printhead, and both the rotational speed of the mixing impeller as well as the fuel–oxidizer ratio are varied. Upon ignition, the propagation speed increases with the rotational speed of the mixer and plateaus above a critical value of ≈750 rpm. The critical mixing speed is corroborated by computational fluid simulations and an analytical expression that considers the inks’ complex fluid behavior. Additionally, varying the composition results in a wide range of propagation speeds with peak reactivity corresponding to a fuel‐rich formulation (ϕ = 1.5). A test article incorporating a fast‐ and slow‐burning region demonstrates how spatial composition can manipulate the reactivity.


  • Top Cited Papers
    Open Access

    Field responsive mechanical metamaterials

    by Julie A. Jackson, Mark C. Messner, Nikola A. Dudukovic, William L. Smith, Logan Bekker, Bryan Moran, Alexandra M. Golobic, Andrew J. Pascall, Eric B. Duoss, Kenneth J. Loh, et al.

    We present a new class of architected materials that exhibit rapid, reversible, and sizable changes in effective stiffness.