Takeshi Yao
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Takeshi Yao has a total of 45 co-authors. Here are the top co-authors by number of shared publications:
- Takeshi Yabutsuka
Graduate School of Energy Science, Kyoto University, Kyoto 606-8501, Japan
15 shared publications - Shigeomi Takai
Graduate School of Energy Science, Kyoto University, Kyoto 606-8501, Japan
14 shared publications Yoshio Oka
Department of Natural Environment Sciences, Faculty of Integrated Human Studies, Graduate School of Energy Sciences, Kyoto University, Kyoto, 606-8501, Japan
5 shared publicationsNaoichi Yamamoto
Faculty of Integrated Human Studies, Graduate School of Energy Sciences, Graduate School of Human and Environmental Studies, Kyoto University, Kyoto, 606-8501, Japan
4 shared publications- Hiroshi Mizuno
Juntendo University School of Medicine
3 shared publications - Mitsuhiro Hibino
Department of Fundamental Energy Science, Graduate School of Energy Science, Kyoto University, Kyoto 606-8501, Japan
3 shared publications
Latest Publications
- Open Access
- 31 May 2022
- Published by Japan Society of Waste Management Experts in Material Cycles and Waste Management Research
- Vol. 33 (3) , 229-236
Right Selection in Battery Use
電池は身近にありながら,その原理がよく知られているとはいえず,ブラックボックス化しており,これが電池イノベーションの方向を迷わせる原因となっている。その観点から,まず電池発電の原理について解説する。そこから,「反応するものは何でも電池になる」 ことがわかる。電池の成否を決めているのは 「実用性」 であり,その要件には,起電力や充放電サイクル寿命や安全性,さらにはコストやリサイクル等が含まれる。「実用性」 の要件は非常に厳しく,歴史的にこれまでごくわずかな種類の電池が実用化したに過ぎない。電池各種について性能を比較し,その長所と短所を実際の用途とすり合わせながら,最も適合するものを,適材適所に選択していくことが,重要である。新たに開発された高性能鉛蓄電池は,用途によっては,リチウムイオン二次電池に置き換わる可能性を有している。以上の議論を総合して,電池イノベーションの目指すべき方向について提案する。
- 31 May 2022
- Published by Japan Society of Waste Management Experts in Material Cycles and Waste Management Research
- Vol. 33 (3) , 229-236
Open AccessRight Selection in Battery Use
電池は身近にありながら,その原理がよく知られているとはいえず,ブラックボックス化しており,これが電池イノベーションの方向を迷わせる原因となっている。その観点から,まず電池発電の原理について解説する。そこから,「反応するものは何でも電池になる」 ことがわかる。電池の成否を決めているのは 「実用性」 であり,その要件には,起電力や充放電サイクル寿命や安全性,さらにはコストやリサイクル等が含まれる。「実用性」 の要件は非常に厳しく,歴史的にこれまでごくわずかな種類の電池が実用化したに過ぎない。電池各種について性能を比較し,その長所と短所を実際の用途とすり合わせながら,最も適合するものを,適材適所に選択していくことが,重要である。新たに開発された高性能鉛蓄電池は,用途によっては,リチウムイオン二次電池に置き換わる可能性を有している。以上の議論を総合して,電池イノベーションの目指すべき方向について提案する。
- Open Access
Synthesis and Characterization of Lithium-Ion Conductive LATP-LaPO4 Composites Using La2O3 Nano-Powder
LATP-based composite electrolytes were prepared by sintering the mixtures of LATP precursor and La2O3 nano-powder. Powder X-ray diffraction and scanning electron microscopy suggest that La2O3 can react with LATP during sintering to form fine LaPO4 particles that are dispersed in the LATP matrix. The room temperature conductivity initially increases with La2O3 nano-powder addition showing the maximum of 0.69 mS∙cm−1 at 6 wt.%, above which, conductivity decreases with the introduction of La2O3. The activation energy of conductivity is not largely varied with the La2O3 content, suggesting that the conduction mechanism is essentially preserved despite LaPO4 dispersion. In comparison with the previously reported LATP-LLTO system, although some unidentified impurity slightly reduces the conductivity maximum, the fine dispersion of LaPO4 particles can be achieved in the LATP–La2O3 system.
Open AccessSynthesis and Characterization of Lithium-Ion Conductive LATP-LaPO4 Composites Using La2O3 Nano-Powder
LATP-based composite electrolytes were prepared by sintering the mixtures of LATP precursor and La2O3 nano-powder. Powder X-ray diffraction and scanning electron microscopy suggest that La2O3 can react with LATP during sintering to form fine LaPO4 particles that are dispersed in the LATP matrix. The room temperature conductivity initially increases with La2O3 nano-powder addition showing the maximum of 0.69 mS∙cm−1 at 6 wt.%, above which, conductivity decreases with the introduction of La2O3. The activation energy of conductivity is not largely varied with the La2O3 content, suggesting that the conduction mechanism is essentially preserved despite LaPO4 dispersion. In comparison with the previously reported LATP-LLTO system, although some unidentified impurity slightly reduces the conductivity maximum, the fine dispersion of LaPO4 particles can be achieved in the LATP–La2O3 system.
- 6 March 2020
- Published by Elsevier in Journal of Physics and Chemistry of Solids
- Vol. 142, 109440
Relaxation stage analysis of lithium inserted graphite
- 6 March 2020
- Published by Elsevier in Journal of Physics and Chemistry of Solids
- Vol. 142, 109440
Relaxation stage analysis of lithium inserted graphite
- 1 April 2019
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 780, 85-89
Chemical transformation of PbO2 due to local cell reaction on the cathode of lead acid battery
- 1 April 2019
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 780, 85-89
Chemical transformation of PbO2 due to local cell reaction on the cathode of lead acid battery
- Open Access
- 6 December 2018
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 166 (3) , A5153-A5156
Structural Relaxation of LixNi0.874Co0.090Al0.036O2 after Lithium Extraction down to (x ≤ 0.12)
Structural relaxation experiments have been carried out on Lix(Ni0.874Co0.090Al0.036)O2 (Co-9.0 NCA) after the lithium extraction down to x ≤ 0.12. X-ray diffraction has been made during the relaxation process, which were analyzed by the Rietveld method assuming two phases (H2 and H3) co-existence with R3¯mR3¯m symmetry. For the lithium extraction to x = 0.12, Co-9.0 NCA seems to show single H2 phase for all the relaxation period, while H2 and H3 coexistence is detected for x = 0.09 or 0.06. Even for the smaller lithium concentration region, H2 phase is predominant rather than H3. Comparing with the previous study of LiNiO2 and Co-3.1 NCA, very small H2-H3 transition has been observed during the relaxation time, which is due to the relatively larger c-length in H3 phase for highly extracted region (x = 0.06).
- 6 December 2018
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 166 (3) , A5153-A5156
Open AccessStructural Relaxation of LixNi0.874Co0.090Al0.036O2 after Lithium Extraction down to (x ≤ 0.12)
Structural relaxation experiments have been carried out on Lix(Ni0.874Co0.090Al0.036)O2 (Co-9.0 NCA) after the lithium extraction down to x ≤ 0.12. X-ray diffraction has been made during the relaxation process, which were analyzed by the Rietveld method assuming two phases (H2 and H3) co-existence with R3¯mR3¯m symmetry. For the lithium extraction to x = 0.12, Co-9.0 NCA seems to show single H2 phase for all the relaxation period, while H2 and H3 coexistence is detected for x = 0.09 or 0.06. Even for the smaller lithium concentration region, H2 phase is predominant rather than H3. Comparing with the previous study of LiNiO2 and Co-3.1 NCA, very small H2-H3 transition has been observed during the relaxation time, which is due to the relatively larger c-length in H3 phase for highly extracted region (x = 0.06).
- Open Access
Effect of Doubled Sandblasting Process and Basic Simulated Body Fluid Treatment on Fabrication of Bioactive Stainless Steels
In our recent study, we aimed to impart hydroxyapatite (HA)-forming to bioinert stainless steels (SUS316L). The surfaces of SUS316L specimen were treated by a sandblasting process using alumina grinding particles with 14.0 or 3.0 μm for average particle size, respectively. In addition, a doubled sandblasting process (DSP) using the 14.0 μm particles and subsequently 3.0 μm ones were also conducted. Compared with the case of the 14.0 μm particles, the 3.0 μm particles were available to increase the surface roughness and the surface area of the specimen. Moreover, these values were further increased in the case of the DSP. These specimens were soaked in simulated body fluid (SBF) at pH = 8.4, 25 °C and were directly heated in the solution by electromagnetic induction. By this treatment, formation of CaP was induced on each specimen. These materials performed high HA-forming ability in SBF. Average bonding strength of the HA film formed on them in SBF was increased depending on the increase of surface roughness and surface area. These results indicated that sandblasting condition was an important factor to improve interlocking effect related to the increase of the surface roughness and the surface area.
Open AccessEffect of Doubled Sandblasting Process and Basic Simulated Body Fluid Treatment on Fabrication of Bioactive Stainless Steels
In our recent study, we aimed to impart hydroxyapatite (HA)-forming to bioinert stainless steels (SUS316L). The surfaces of SUS316L specimen were treated by a sandblasting process using alumina grinding particles with 14.0 or 3.0 μm for average particle size, respectively. In addition, a doubled sandblasting process (DSP) using the 14.0 μm particles and subsequently 3.0 μm ones were also conducted. Compared with the case of the 14.0 μm particles, the 3.0 μm particles were available to increase the surface roughness and the surface area of the specimen. Moreover, these values were further increased in the case of the DSP. These specimens were soaked in simulated body fluid (SBF) at pH = 8.4, 25 °C and were directly heated in the solution by electromagnetic induction. By this treatment, formation of CaP was induced on each specimen. These materials performed high HA-forming ability in SBF. Average bonding strength of the HA film formed on them in SBF was increased depending on the increase of surface roughness and surface area. These results indicated that sandblasting condition was an important factor to improve interlocking effect related to the increase of the surface roughness and the surface area.
- Open Access
Structural Relaxation of Lix(Ni0.874Co0.090Al0.036)O2 after Lithium Extraction down to x = 0.12
A structural relaxation study has been carried out on Lix(Ni0.874Co0.090Al0.036)O2 after the electrochemical lithium was extraction down to x = 0.12. These relaxation analyses have been carried out using X-ray diffraction coupled with the Rietveld analysis, assuming two phases (H2 and H3) and co-existence with symmetry. The mole fraction of the H3 phase seemed not to vary largely during the relaxation time. As for the lattice constants, both H2 and H3 phases gradually increased the a-axis with the relaxation time. On the other hand, H2 and H3 phases increased and decreased the c-axis, respectively. The results are compared with that of previously reported Ni-rich NCA.Open AccessStructural Relaxation of Lix(Ni0.874Co0.090Al0.036)O2 after Lithium Extraction down to x = 0.12
A structural relaxation study has been carried out on Lix(Ni0.874Co0.090Al0.036)O2 after the electrochemical lithium was extraction down to x = 0.12. These relaxation analyses have been carried out using X-ray diffraction coupled with the Rietveld analysis, assuming two phases (H2 and H3) and co-existence with symmetry. The mole fraction of the H3 phase seemed not to vary largely during the relaxation time. As for the lattice constants, both H2 and H3 phases gradually increased the a-axis with the relaxation time. On the other hand, H2 and H3 phases increased and decreased the c-axis, respectively. The results are compared with that of previously reported Ni-rich NCA. - Open Access
Defect Structure and Oxide Ion Conduction of Potassium Ion Substituted CaWO4
We have prepared Ca1−xKxWO4−x/2 solid solutions with the Scheelite-type structure to investigate high-temperature electrochemical properties. Room-temperature X-ray diffraction suggested the solid solution range was x ≤ 0.2, since the second phase presumably of K2WO4 was detected for x = 0.3. For all the substituted samples up to x = 0.4, a large jump in conductivity has been observed around 500 °C. At higher temperatures, oxide ion conduction is found to be predominant even for x = 0.4, exceeding the solution limit estimated from the room-temperature XRD. The conductivity at high temperature is essentially proportional to the amount of substituted potassium ions up to x = 0.4, indicating that oxide ion conduction is associated with the formed oxide ion vacancy. High-temperature X-ray diffraction detected no apparent change in lattice parameters around 500 °C for x = 0.1, and the remaining second phase seems to be incorporated into the Scheelite lattice at high temperatures.
Open AccessDefect Structure and Oxide Ion Conduction of Potassium Ion Substituted CaWO4
We have prepared Ca1−xKxWO4−x/2 solid solutions with the Scheelite-type structure to investigate high-temperature electrochemical properties. Room-temperature X-ray diffraction suggested the solid solution range was x ≤ 0.2, since the second phase presumably of K2WO4 was detected for x = 0.3. For all the substituted samples up to x = 0.4, a large jump in conductivity has been observed around 500 °C. At higher temperatures, oxide ion conduction is found to be predominant even for x = 0.4, exceeding the solution limit estimated from the room-temperature XRD. The conductivity at high temperature is essentially proportional to the amount of substituted potassium ions up to x = 0.4, indicating that oxide ion conduction is associated with the formed oxide ion vacancy. High-temperature X-ray diffraction detected no apparent change in lattice parameters around 500 °C for x = 0.1, and the remaining second phase seems to be incorporated into the Scheelite lattice at high temperatures.
- 1 June 2018
- Published by The Materials Research Society of Japan in Transactions of the Materials Research Society of Japan
- Vol. 43 (3) , 139-142
Bioactivity Treatment to Polylactic Acid Fabric Cloth and Foam by Precipitation of Apatite Nuclei
- 1 June 2018
- Published by The Materials Research Society of Japan in Transactions of the Materials Research Society of Japan
- Vol. 43 (3) , 139-142
Bioactivity Treatment to Polylactic Acid Fabric Cloth and Foam by Precipitation of Apatite Nuclei
- 1 June 2018
- Published by The Materials Research Society of Japan in Transactions of the Materials Research Society of Japan
- Vol. 43 (3) , 149-152
Effective Procedure of Bioactivity Treatment to Bearing Grade PEEK by Incorporation of Apatite Nuclei
- 1 June 2018
- Published by The Materials Research Society of Japan in Transactions of the Materials Research Society of Japan
- Vol. 43 (3) , 149-152
Effective Procedure of Bioactivity Treatment to Bearing Grade PEEK by Incorporation of Apatite Nuclei