Songhao Hu
Research Subjects
Songhao Hu has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Mingyang Zhang
Powder Metallurgy Research Institute, Central South University, Changsha 410083, China
3 shared publications - Wei Zhang
State Key Laboratory of Powder Metallurgy, Central South University, Changsha 410083, China
3 shared publications - Yingbo Peng
Nanjing Agr Univ, Coll Engn, Nanjing 210094, Peoples R China
3 shared publications - Yong Liu
Central South University
3 shared publications - Fangzhou Liu
Powder Metallurgy Research Institute, Central South University, Changsha 410083, China
2 shared publications - Yang Hu
Yuanmeng Precision Technology (Shenzhen) Institute, Shenzhen 518055, China
2 shared publications
Latest Publications
- Open Access
Gradient Distribution of Microstructures and Mechanical Properties in a FeCoCrNiMo High-Entropy Alloy during Spark Plasma Sintering
A novel graded material of a high-entropy alloy (HEA) FeCoCrNiMo was fabricated by spark plasma sintering (SPS) processing. After SPS, the HEA specimens consisted of a single face-centred cubic (FCC) phase in the center, but dual FCC and a tetragonal structure σ phase near the surface. Surprisingly, the sintering pressure was sufficient to influence the proportion of phases, and thus the properties of HEA samples. The hardness of the specimens sintered under the pressures of 30, 35, and 40 MPa increased gradually from 210 HV0.2, which is the single FCC phase in the center, to the maximum value near the surface as a result of the gradual increase in the fraction of the transformed σ phase. The σ phase, being a complex hard and brittle intermetallic particle to manipulate the properties of FCC-type HEA systems, which could be influenced by pressure, indicated a major possibility for designing gradient HEA materials.
Open AccessGradient Distribution of Microstructures and Mechanical Properties in a FeCoCrNiMo High-Entropy Alloy during Spark Plasma Sintering
A novel graded material of a high-entropy alloy (HEA) FeCoCrNiMo was fabricated by spark plasma sintering (SPS) processing. After SPS, the HEA specimens consisted of a single face-centred cubic (FCC) phase in the center, but dual FCC and a tetragonal structure σ phase near the surface. Surprisingly, the sintering pressure was sufficient to influence the proportion of phases, and thus the properties of HEA samples. The hardness of the specimens sintered under the pressures of 30, 35, and 40 MPa increased gradually from 210 HV0.2, which is the single FCC phase in the center, to the maximum value near the surface as a result of the gradual increase in the fraction of the transformed σ phase. The σ phase, being a complex hard and brittle intermetallic particle to manipulate the properties of FCC-type HEA systems, which could be influenced by pressure, indicated a major possibility for designing gradient HEA materials.
- Open Access
Effect of Ti/Ni Coating of Diamond Particles on Microstructure and Properties of High-Entropy Alloy/Diamond Composites
In this study, an effective way of applying Ti/Ni deposited coating to the surface of diamond single crystal particles by magnetron sputtering was proposed and novel high-entropy alloy (HEA)/diamond composites were prepared by spark plasma sintering (SPS). The results show that the interfacial bonding state of the coated diamond composite is obviously better than that of the uncoated diamond composite. Corresponding mechanical properties such as hardness, density, transverse fracture strength and friction properties of the coated diamond composite were also found to be better than those of the uncoated diamond composite. The effects of interface structure and defects on the mechanical properties of HEA/diamond composites were investigated. The research directions for further improving the structure and properties of high-entropy alloy/diamond composites were proposed.
Open AccessEffect of Ti/Ni Coating of Diamond Particles on Microstructure and Properties of High-Entropy Alloy/Diamond Composites
In this study, an effective way of applying Ti/Ni deposited coating to the surface of diamond single crystal particles by magnetron sputtering was proposed and novel high-entropy alloy (HEA)/diamond composites were prepared by spark plasma sintering (SPS). The results show that the interfacial bonding state of the coated diamond composite is obviously better than that of the uncoated diamond composite. Corresponding mechanical properties such as hardness, density, transverse fracture strength and friction properties of the coated diamond composite were also found to be better than those of the uncoated diamond composite. The effects of interface structure and defects on the mechanical properties of HEA/diamond composites were investigated. The research directions for further improving the structure and properties of high-entropy alloy/diamond composites were proposed.
- Open Access
Effect of Binding and Dispersion Behavior of High-Entropy Alloy (HEA) Powders on the Microstructure and Mechanical Properties in a Novel HEA/Diamond Composite
This study reports the results of the addition of diamonds in the sintering process of a FCC-structured CoCrFeNiMo high-entropy alloy. The effect of raw powder states such as elemental mixed (EM) powder, gas atomization (GA) powder and mechanical alloying (MA) powder on the uniformity of constituent phase was also investigated. Examination of microstructure and evaluation of mechanical properties of the composites depending on the mixing processes were performed. As a result, GA+MA powder composite showed the highest mechanical properties. The experimental results indicated that the powder manufacturing method was an essential parameter to determine the quality of HEA/diamond composites such as the uniformity of phase and binding behavior.
Open AccessEffect of Binding and Dispersion Behavior of High-Entropy Alloy (HEA) Powders on the Microstructure and Mechanical Properties in a Novel HEA/Diamond Composite
This study reports the results of the addition of diamonds in the sintering process of a FCC-structured CoCrFeNiMo high-entropy alloy. The effect of raw powder states such as elemental mixed (EM) powder, gas atomization (GA) powder and mechanical alloying (MA) powder on the uniformity of constituent phase was also investigated. Examination of microstructure and evaluation of mechanical properties of the composites depending on the mixing processes were performed. As a result, GA+MA powder composite showed the highest mechanical properties. The experimental results indicated that the powder manufacturing method was an essential parameter to determine the quality of HEA/diamond composites such as the uniformity of phase and binding behavior.