LWLars I. van der Wal

Lars I. van der Wal

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Lars I. van der Wal has a total of 35 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Top Cited Papers

    Maximizing noble metal utilization in solid catalysts by control of nanoparticle location

    by Kang Cheng, Luc C. J. Smulders, Lars I. van der Wal, Jogchum Oenema, Johannes D. Meeldijk, Nienke L. Visser, Glenn Sunley, Tegan Roberts, Zhuoran Xu, Eric Doskocil, et al.

    Maximizing the utilization of noble metals is crucial for applications such as catalysis. We found that the minimum loading of platinum for optimal performance in the hydroconversion of n -alkanes for industrially relevant bifunctional catalysts could be reduced by a factor of 10 or more through the rational arranging of functional sites at the nanoscale. Intentionally depositing traces of platinum nanoparticles on the alumina binder or the outer surface of zeolite crystals, instead of inside the zeolite crystals, enhanced isomer selectivity without compromising activity. Separation between platinum and zeolite acid sites preserved the metal and acid functions by limiting micropore blockage by metal clusters and enhancing access to metal sites. Reduced platinum nanoparticles were more active than platinum single atoms strongly bonded to the alumina binder.


  • Developments and advances in in situ transmission electron microscopy for catalysis research

    by Lars I. van der Wal, Savannah J. Turner, Jovana Zečević

    The characterization of heterogeneous catalysts is critical to their development and to understand their performance by correlating their physicochemical properties to their activity, selectivity and stability. Transmission electron microscopy (TEM) is one of the routinely used characterization techniques, and is commonly limited to investigations of catalyst samples before and after synthesis, activation, and operation. Thus only indirect information can be obtained about structural transformations undergone by the catalyst during synthesis or catalysis. Effort over the decades in developing in situ TEM is showing promising results whereby the direct, real-time observation of the structural changes of materials under reaction conditions are becoming available. In this review we provide an overview of the developments in in situ TEM techniques, focusing on their application for studies related to catalysis by loosely following the four stages of the catalyst life cycle: synthesis, activation, performance and deactivation, and regeneration.


  • Open Access

    Influence of intimacy for metal-mesoporous solid acids catalysts for n -alkanes hydro-conversion

    by Justine Harmel, Lars I. van der Wal, Jovana Zečević, Petra E. de Jongh, Krijn P. de Jong

    Pt on both ordered mesoporous Al-SBA-15 and commercial amorphous mesoporous silica-alumina bi-functional catalysts were prepared and studied for n-heptane hydro-isomerization and n-hexadecane hydro-cracking. We investigated the influence of the location of the Pt nanoarticles and their proximity to the acid sites; by depositing Pt in a controlled manner either in the mesopores of the solid acid or on a γ-Al2O3 binder, surrounding the solid acid particles. We demonstrate that in the case of both ordered and amorphous mesoporous acidic support, a distance between the metal and acid sites of a hundreds of nanometers gives similar results compared to the closest intimacy (below 10 nm) between these functions. Due to the medium strength Brønsted acid sites of the Al-SBA-15, Pt-Al-SBA-15 exhibits higher activity than the corresponding Pt on commercial amorphous silica-alumina. These results suggest that, in the case of mesoporous solid acids, a fine control at the nanoscale of the proximity between the active sites is less important than the number and nature of the acid sites.


  • Open Access

    Stability of mesocellular foam supported copper catalysts for methanol synthesis

    by C.E. Pompe, D.L. van Uunen, L.I. van der Wal, J.E.S. van der Hoeven, K.P. de Jong, P.E. de Jongh


  • Open Access

    Increasing the activity of copper exchanged mordenite in the direct isothermal conversion of methane to methanol by Pt and Pd doping

    by P. Tomkins, A. Mansouri, V. L. Sushkevich, L. I. van der Wal, S. E. Bozbag, F. Krumeich, M. Ranocchiari, J. A. van Bokhoven

    PtCu– and PdCu–mordenite allow for isothermal reaction at 200 °C for the stepwise methane to methanol conversion with higher yields under isothermal conditions than after high temperature activation.


  • Open Access

    Structure sensitivity of Cu and CuZn catalysts relevant to industrial methanol synthesis

    by Roy van Den Berg, Gonzalo Prieto, Gerda Korpershoek, Lars I. van der Wal, Arnoldus J. van Bunningen, Susanne Lægsgaard-Jørgensen, Petra E. de Jongh, Krijn P. de Jong

    For decades it has been debated whether the conversion of synthesis gas to methanol over copper catalysts is sensitive or insensitive to the structure of the copper surface. Here we have systematically investigated the effect of the copper particle size in the range where changes in surface structure occur, that is, below 10 nm, for catalysts with and without zinc promotor at industrially relevant conditions for methanol synthesis. Regardless of the presence or absence of a zinc promotor in the form of zinc oxide or zinc silicate, the surface-specific activity decreases significantly for copper particles smaller than 8 nm, thus revealing structure sensitivity. In view of recent theoretical studies we propose that the methanol synthesis reaction takes place at copper surface sites with a unique configuration of atoms such as step-edge sites, which smaller particles cannot accommodate.