Hongbo Yang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Hongbo Yang has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
Huan Liu
School of Metallurgical Engineering, Xi'an University of Architecture and Technology, Xi'an 710055, China
3 shared publicationsPeiwen Yao
School of Metallurgical Engineering, Xi'an University of Architecture and Technology, Xi'an 710055, China
3 shared publications- Mingzeng Shao
School of Metallurgical Engineering, Xi’an University of Architecture and Technology, Xi’an 710055, China
1 shared publication - Wei Wang
Xi’an University of Architecture and Technology
1 shared publication - Xiaomei He
School of Metallurgical Engineering, Xi’an University of Architecture and Technology, Xi’an 710055, China
1 shared publication - Xueer Zhang
School of Metallurgical Engineering, Xi’an University of Architecture and Technology, Xi’an 710055, China
1 shared publication
Latest Publications
- Open Access
Preparation of Wear-Resistant Coating on Ti6Al4V Alloy by Cold Spraying and Plasma Electrolytic Oxidation
In order to improve the wear resistance of Ti6Al4V alloy, the alloy was first coated with alumina-reinforced aluminum coating (CS-coating) by cold spraying, and then the alloy with CS-coating was processed by plasma electrolytic oxidation (PEO) under unipolar mode and soft sparking mode, respectively, to prepare wear-resistant PEO coatings. For comparison, Ti6Al4V alloy without CS-coating was also subjected to PEO treatment. The microstructure, phase composition, hardness, and wear resistance of the PEO coatings formed on Ti6Al4V alloy with and without CS-coating were investigated. The results revealed that PEO coatings formed on Ti6Al4V alloy with CS-coating under soft sparking mode contained more α-Al2O3, possessed larger thickness, more compact microstructure, and higher microhardness than that formed under unipolar mode. The PEO coating formed on Ti6Al4V substrate was mainly composed of TiO2 and had pores and cracks. Among all these coatings, PEO coating formed on Ti6Al4V alloy with CS-coating under soft sparking mode exhibited the best wear resistance with a wear rate of 1.18 × 10−5 mm3/(Nm), which was only 15.28% of that of the Ti6Al4V substrate. The investigation indicated that the combination of cold spraying and PEO under soft sparking mode is a promising technique for improving the wear resistance of titanium alloy.
Open AccessPreparation of Wear-Resistant Coating on Ti6Al4V Alloy by Cold Spraying and Plasma Electrolytic Oxidation
In order to improve the wear resistance of Ti6Al4V alloy, the alloy was first coated with alumina-reinforced aluminum coating (CS-coating) by cold spraying, and then the alloy with CS-coating was processed by plasma electrolytic oxidation (PEO) under unipolar mode and soft sparking mode, respectively, to prepare wear-resistant PEO coatings. For comparison, Ti6Al4V alloy without CS-coating was also subjected to PEO treatment. The microstructure, phase composition, hardness, and wear resistance of the PEO coatings formed on Ti6Al4V alloy with and without CS-coating were investigated. The results revealed that PEO coatings formed on Ti6Al4V alloy with CS-coating under soft sparking mode contained more α-Al2O3, possessed larger thickness, more compact microstructure, and higher microhardness than that formed under unipolar mode. The PEO coating formed on Ti6Al4V substrate was mainly composed of TiO2 and had pores and cracks. Among all these coatings, PEO coating formed on Ti6Al4V alloy with CS-coating under soft sparking mode exhibited the best wear resistance with a wear rate of 1.18 × 10−5 mm3/(Nm), which was only 15.28% of that of the Ti6Al4V substrate. The investigation indicated that the combination of cold spraying and PEO under soft sparking mode is a promising technique for improving the wear resistance of titanium alloy.
- Open Access
- 22 March 2019
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 493 (1) , 012034
Study on austenite recrystallization softening behavior of GCr15 steel
The double-pass hot compression tests were carried out by MMS-300 thermal simulator. The effects of deformation temperature, deformation amount, strain rate, and austenite grain size on sub-dynamic recrystallization and static recrystallization of GCr15 bearing steel were studied systematically. Based on this, the microstructure controlling of invested steel wire rods during rolling was discussed in this paper, which can provide a basis for the reasonable determination of heating and deformation in the actual production process.
- 22 March 2019
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 493 (1) , 012034
Open AccessStudy on austenite recrystallization softening behavior of GCr15 steel
The double-pass hot compression tests were carried out by MMS-300 thermal simulator. The effects of deformation temperature, deformation amount, strain rate, and austenite grain size on sub-dynamic recrystallization and static recrystallization of GCr15 bearing steel were studied systematically. Based on this, the microstructure controlling of invested steel wire rods during rolling was discussed in this paper, which can provide a basis for the reasonable determination of heating and deformation in the actual production process.
- Open Access
- 22 March 2019
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 493 (1) , 012108
Research status and development of explosive welded metal materials
Explosive welding composites have been widely used in aerospace, petroleum, chemical, military and other fields, because of their characteristics of corrosion resistance, heat resistance and high strength. The theoretical research of metal explosive welded materials was introduced systematically, and the significance and trends of interface research were analyzed in this paper. Finally, the development trend of explosive welding of metal materials is prospected. It is pointed out that the prediction of damage behavior of explosive welding composites in service environment has certain scientific significance and engineering application value.
- 22 March 2019
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 493 (1) , 012108
Open AccessResearch status and development of explosive welded metal materials
Explosive welding composites have been widely used in aerospace, petroleum, chemical, military and other fields, because of their characteristics of corrosion resistance, heat resistance and high strength. The theoretical research of metal explosive welded materials was introduced systematically, and the significance and trends of interface research were analyzed in this paper. Finally, the development trend of explosive welding of metal materials is prospected. It is pointed out that the prediction of damage behavior of explosive welding composites in service environment has certain scientific significance and engineering application value.
- Open Access
- 12 December 2018
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 452 (2) , 022130
Study on high temperature deformation behaviour of GCr15 bearing steel
The high temperature rheological curves of GCr15 bearing steel at different temperatures and strain rates were studied by MMS-300 thermal simulator. The dynamic recrystallization behaviour of GCr15 steel was analyzed with metallographic microscope. The dynamic recrystallization behavior of GCr15 steel was analyzed by combining metallographic microscope. The effects of austenitizing temperature, deformation amount, and strain rate on the dynamic recrystallization of tested steel were systematically studied. Based on this, the equation of hot working is established, and it is pointed out that the activation energy of hot deformation of GCr15 bearing steel is 291.35 kJ/mol.
- 12 December 2018
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 452 (2) , 022130
Open AccessStudy on high temperature deformation behaviour of GCr15 bearing steel
The high temperature rheological curves of GCr15 bearing steel at different temperatures and strain rates were studied by MMS-300 thermal simulator. The dynamic recrystallization behaviour of GCr15 steel was analyzed with metallographic microscope. The dynamic recrystallization behavior of GCr15 steel was analyzed by combining metallographic microscope. The effects of austenitizing temperature, deformation amount, and strain rate on the dynamic recrystallization of tested steel were systematically studied. Based on this, the equation of hot working is established, and it is pointed out that the activation energy of hot deformation of GCr15 bearing steel is 291.35 kJ/mol.