Zhuo Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Zhuo Wang has a total of 74 co-authors. Here are the top co-authors by number of shared publications:
- Bo Zhang
University of Electronic Science and Technology of China
16 shared publications - Zekun Zhou
University of Electronic Science and Technology of China
7 shared publications - Yue Shi
State Key Laboratory of Electronic Thin Films and Integrated Devices, University of Electronic Science and Technology of China, Chengdu, China
6 shared publications - Ming Qiao
University of Electronic Science and Technology of China
5 shared publications - Xin Ming
Shenzhen Institute for Advanced Study, UESTC, Shenzhen, China
5 shared publications Zhaoji Li
State Key Laboratory of Electronic Thin Films and Integrated Devices, University of Electronic Science and Technology of China (UESTC), Chengdu, China
4 shared publications
Latest Publications
- 1 November 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 73 (11) , 7535-7546
A Wide-Load High-Stability LDO With Dynamic Semi-Pole Compensation and Capacitor Tracking Technique
- 1 November 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 73 (11) , 7535-7546
A Wide-Load High-Stability LDO With Dynamic Semi-Pole Compensation and Capacitor Tracking Technique
- 30 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 72 (11) , 6411-6422
A Charge-Sharing-Based Half-Bridge Driver Suitable for Any Duty Cycle With No External Component
A fully-integrated half-bridge driver with dual N-type power transistors is proposed in this paper, which adopts on-chip charge pumps with integrated capacitors based on charge sharing to avoid external bootstrap components. Without bootstrap-capacitor charging paths through low-side power transistors and high-frequency high-power switching nodes, overcharge and large electro-magnetic interference (EMI) can be avoided by eliminating parasitic interconnect inductance and body diode. Adaptive dead time is employed to enhance efficiency, enabling the system to achieve appropriate dead times in various applications. Besides, 100% duty-cycle control is realized by duty-cycle detection and additional continuous charge pump, which can charge the on-chip driver capacitor during on-time, the restriction of minimum off-time is eliminated and the proposed driver can work at full duty cycle range. The proposed charge-sharing-based (CSB) half-bridge driver with any duty-cycle capability embedded in a buck converter with 2A load is implemented in a $0.18~\mu $ m BCD technology, which occupies an active area of 0.151mm2. Verification results demonstrate that a 2.2 MHz switching frequency is realized with 2.4V–5.5V input voltage and a peak efficiency of 96.8% is achieved for 5 to 4V conversion. The minimum regulation voltage difference between input voltage and output voltage is 70 mV with the help of 100% duty-cycle circuit.
- 30 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 72 (11) , 6411-6422
A Charge-Sharing-Based Half-Bridge Driver Suitable for Any Duty Cycle With No External Component
A fully-integrated half-bridge driver with dual N-type power transistors is proposed in this paper, which adopts on-chip charge pumps with integrated capacitors based on charge sharing to avoid external bootstrap components. Without bootstrap-capacitor charging paths through low-side power transistors and high-frequency high-power switching nodes, overcharge and large electro-magnetic interference (EMI) can be avoided by eliminating parasitic interconnect inductance and body diode. Adaptive dead time is employed to enhance efficiency, enabling the system to achieve appropriate dead times in various applications. Besides, 100% duty-cycle control is realized by duty-cycle detection and additional continuous charge pump, which can charge the on-chip driver capacitor during on-time, the restriction of minimum off-time is eliminated and the proposed driver can work at full duty cycle range. The proposed charge-sharing-based (CSB) half-bridge driver with any duty-cycle capability embedded in a buck converter with 2A load is implemented in a $0.18~\mu $ m BCD technology, which occupies an active area of 0.151mm2. Verification results demonstrate that a 2.2 MHz switching frequency is realized with 2.4V–5.5V input voltage and a peak efficiency of 96.8% is achieved for 5 to 4V conversion. The minimum regulation voltage difference between input voltage and output voltage is 70 mV with the help of 100% duty-cycle circuit.
- 28 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 59 (2) , 583-594
An NMOS LDO With TM-MOS and Dynamic Clamp Technique Handling Up To Sub-10-μs Short-Period Load Transient
A current-efficient and fast-transient n-type low-dropout regulator (LDO) for high-frequency load transient in mobile phone applications is presented in this article. By using transconductance magnified MOS (TM-MOS), it reduces LDO’s output impedance with fast response speed and keeps high current efficiency. Moreover, based on load-current sensing of TM-MOS, active clamp strategy is implemented to optimize the driving dead zone (DDZ) of this NMOS LDO and achieve good high-frequency load transient performance. Robust loop stability for a wide load-current range is ensured as well with the help of revised Type-II frequency compensation. This circuit has been implemented in a 0.35-$\mu$ m standard CMOS process and occupies an active chip area of 470$\times$ 280$\mu$ m$^{2}$ . With a 1-$\mu$ F output cap and load steps between 0 A and 300 mA, experimental results show that it features 50/36 mV of undershoot/overshoot at low-frequency load transient and 68/36 mV of undershoot/overshoot at the high-frequency load transient (i.e., 10-$\mu$ s light-load duration). This regulator consumes 8.2-$\mu$ A quiescent current, achieving 99.68% equivalent current efficiency at 300-mA load current.- 28 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 59 (2) , 583-594
An NMOS LDO With TM-MOS and Dynamic Clamp Technique Handling Up To Sub-10-μs Short-Period Load Transient
A current-efficient and fast-transient n-type low-dropout regulator (LDO) for high-frequency load transient in mobile phone applications is presented in this article. By using transconductance magnified MOS (TM-MOS), it reduces LDO’s output impedance with fast response speed and keeps high current efficiency. Moreover, based on load-current sensing of TM-MOS, active clamp strategy is implemented to optimize the driving dead zone (DDZ) of this NMOS LDO and achieve good high-frequency load transient performance. Robust loop stability for a wide load-current range is ensured as well with the help of revised Type-II frequency compensation. This circuit has been implemented in a 0.35-$\mu$ m standard CMOS process and occupies an active chip area of 470$\times$ 280$\mu$ m$^{2}$ . With a 1-$\mu$ F output cap and load steps between 0 A and 300 mA, experimental results show that it features 50/36 mV of undershoot/overshoot at low-frequency load transient and 68/36 mV of undershoot/overshoot at the high-frequency load transient (i.e., 10-$\mu$ s light-load duration). This regulator consumes 8.2-$\mu$ A quiescent current, achieving 99.68% equivalent current efficiency at 300-mA load current.- 27 January 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 70 (3) , 1206-1210
The Minimum Specific On-Resistance of 3-D Superjunction Devices
The minimum specific ON-resistance${R}_{on,min}$ of the three-dimensional superjunction (3-D SJ) device is realized in this article. The electric field of the 3-D SJ is treated as a vector superposition of a 1-D potential field${E}_{p}$ and a 3-D charge electric field${E}_{q}$ (${x}$ ,${r}$ ,$\theta $ ) that is first deduced by solving the 3-D Poisson’s equation with the Taylor series method. Then, the optimization essence of the 3-D SJ is revealed as the variable modulation of 3-D${E}_{q}$ (${x}$ ,${r}$ ,$\theta $ ) on${E}_{p}$ . The only${R}_{\text {on,min}}$ of the 3-D SJ under given cell pitch${W}$ and breakdown voltage${V}_{B}$ is searched in its global doping range to give design formulas. It is found from the model that the 3-D SJ shows a new${R}_{\text {on,min}} \propto ~{V}_{B}^{1.03}$ relationship lower than that of the optimized 2-D SJ. The analytical results are in good agreement with the simulations.- 27 January 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 70 (3) , 1206-1210
The Minimum Specific On-Resistance of 3-D Superjunction Devices
The minimum specific ON-resistance${R}_{on,min}$ of the three-dimensional superjunction (3-D SJ) device is realized in this article. The electric field of the 3-D SJ is treated as a vector superposition of a 1-D potential field${E}_{p}$ and a 3-D charge electric field${E}_{q}$ (${x}$ ,${r}$ ,$\theta $ ) that is first deduced by solving the 3-D Poisson’s equation with the Taylor series method. Then, the optimization essence of the 3-D SJ is revealed as the variable modulation of 3-D${E}_{q}$ (${x}$ ,${r}$ ,$\theta $ ) on${E}_{p}$ . The only${R}_{\text {on,min}}$ of the 3-D SJ under given cell pitch${W}$ and breakdown voltage${V}_{B}$ is searched in its global doping range to give design formulas. It is found from the model that the 3-D SJ shows a new${R}_{\text {on,min}} \propto ~{V}_{B}^{1.03}$ relationship lower than that of the optimized 2-D SJ. The analytical results are in good agreement with the simulations.- Top Cited Papers
- 5 April 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 37 (9) , 10332-10347
A Fast-Transient Capacitorless LDO With Dual Paths Active-Frequency Compensation Scheme
This article presents an area-efficient and fast-transient capless low-dropout regulator (LDO) with satisfactory static and dynamic performance in the full load current range. Active-capacitor frequency compensation strategy with push–pull charging ability is employed to reduce on-chip compensation cap without degrading loop stability at light load and improve transient response speed simultaneously. Moreover, in order to drive this compensation capacitance, it makes use of an adaptively biased signal- and transient-current boosting error amplifier as well as transient enhancement circuit with nonlinear control to achieve high loop gain/bandwidth and slew rate. The proposed LDO is implemented in a 0.35-μm 5V-CMOS process and occupies an active chip area of 0.077 mm 2 . Experimental results demonstrate that it can deliver 100-mA load current at 200-mV dropout voltage ( V IN = 2.7–3.3 V, C load ≤100 pF). It consumes 66- μ A quiescent current at light load and can recover within 0.7 μ s for load transient. The voltage spikes at the output, undergoing a maximum load current change, are controlled well below 260 mV and good line/load regulation is achieved synchronously.
- 5 April 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 37 (9) , 10332-10347
Top Cited PapersA Fast-Transient Capacitorless LDO With Dual Paths Active-Frequency Compensation Scheme
This article presents an area-efficient and fast-transient capless low-dropout regulator (LDO) with satisfactory static and dynamic performance in the full load current range. Active-capacitor frequency compensation strategy with push–pull charging ability is employed to reduce on-chip compensation cap without degrading loop stability at light load and improve transient response speed simultaneously. Moreover, in order to drive this compensation capacitance, it makes use of an adaptively biased signal- and transient-current boosting error amplifier as well as transient enhancement circuit with nonlinear control to achieve high loop gain/bandwidth and slew rate. The proposed LDO is implemented in a 0.35-μm 5V-CMOS process and occupies an active chip area of 0.077 mm 2 . Experimental results demonstrate that it can deliver 100-mA load current at 200-mV dropout voltage ( V IN = 2.7–3.3 V, C load ≤100 pF). It consumes 66- μ A quiescent current at light load and can recover within 0.7 μ s for load transient. The voltage spikes at the output, undergoing a maximum load current change, are controlled well below 260 mV and good line/load regulation is achieved synchronously.
- 1 February 2022
- Published by The Electrochemical Society in ECS Journal of Solid State Science and Technology
- Vol. 11 (2) , 025002
Reverse Blocking GaN High Electron Mobility Transistors with Stepped P-GaN Drain
In this work, a reverse-blocking high electron mobility transistor with stepped p-type GaN drain (SPD RB-HEMT) has been proposed and studied in TCAD Sentaurus. In SPD RB-HEMT, the reverse-blocking capability is achieved by employing a stepped p-type GaN (P-GaN) layer connected with the Schottky metal drain. The stepped P-GaN layer is constituted by four P-GaN steps, and the thicknesses of the first to the fourth P-GaN step are descending from the source to the drain side. Due to the P-GaN/AlGaN/GaN structure, the conduction band of the AlGaN/GaN interface is lifted up. Therefore, the two-dimensional electron gas (2-DEG) channel is depleted, and the reverse current is blocked. On the other hand, when the drain is forward biased, the 2-DEG channel is recovered, and the drain induced barrier lowering (DIBL) effect in stepped P-GaN drain structure can lead to a lower on-resistance of the device. The SPD RB-HEMT exhibits a reverse breakdown voltage of −2209 V and on-resistance of 3.01 mΩ·cm 2 in TCAD Sentaurus simulation. Compared with the conventional Schottky barrier drain and planar P-GaN drain RB-HEMTs, the SPD RB-HEMTs have shown the balanced and improved forward and reverse-blocking characteristics.
- 1 February 2022
- Published by The Electrochemical Society in ECS Journal of Solid State Science and Technology
- Vol. 11 (2) , 025002
Reverse Blocking GaN High Electron Mobility Transistors with Stepped P-GaN Drain
In this work, a reverse-blocking high electron mobility transistor with stepped p-type GaN drain (SPD RB-HEMT) has been proposed and studied in TCAD Sentaurus. In SPD RB-HEMT, the reverse-blocking capability is achieved by employing a stepped p-type GaN (P-GaN) layer connected with the Schottky metal drain. The stepped P-GaN layer is constituted by four P-GaN steps, and the thicknesses of the first to the fourth P-GaN step are descending from the source to the drain side. Due to the P-GaN/AlGaN/GaN structure, the conduction band of the AlGaN/GaN interface is lifted up. Therefore, the two-dimensional electron gas (2-DEG) channel is depleted, and the reverse current is blocked. On the other hand, when the drain is forward biased, the 2-DEG channel is recovered, and the drain induced barrier lowering (DIBL) effect in stepped P-GaN drain structure can lead to a lower on-resistance of the device. The SPD RB-HEMT exhibits a reverse breakdown voltage of −2209 V and on-resistance of 3.01 mΩ·cm 2 in TCAD Sentaurus simulation. Compared with the conventional Schottky barrier drain and planar P-GaN drain RB-HEMTs, the SPD RB-HEMTs have shown the balanced and improved forward and reverse-blocking characteristics.
- 28 June 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 68 (8) , 3956-3962
Analytical Model and Mechanism of Homogenization Field for Lateral Power Devices
The analytical model and mechanism of homogenization field (HOF) for lateral power devices is developed in this article. The HOF structure features periodical voltage sustaining cells connected in series from source to drain, which introduces the periodic field modulation to realize the 3-D homogenization of electric field. In the model, the periodic electric field distribution of the HOF structure is obtained by solving the Poisson's equation in one half HOF-cell. Then, a design formula is deduced by considering the optimal field distribution. Two lateral double-diffused metal-oxide semiconductor (LDMOS) devices using the HOF structure were fabricated to demonstrate the analytical model. The analytical model is in good agreement with both the simulations and experiments. In the experiments, a low R ON,sp of 53.3mΩ·cm 2 was realized under a high V B of 669.5 V, achieving a HOF LDMOS with high figure of merit FOM = V B 2 /R ON,sp of 8.41 MW/cm 2 .
- 28 June 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 68 (8) , 3956-3962
Analytical Model and Mechanism of Homogenization Field for Lateral Power Devices
The analytical model and mechanism of homogenization field (HOF) for lateral power devices is developed in this article. The HOF structure features periodical voltage sustaining cells connected in series from source to drain, which introduces the periodic field modulation to realize the 3-D homogenization of electric field. In the model, the periodic electric field distribution of the HOF structure is obtained by solving the Poisson's equation in one half HOF-cell. Then, a design formula is deduced by considering the optimal field distribution. Two lateral double-diffused metal-oxide semiconductor (LDMOS) devices using the HOF structure were fabricated to demonstrate the analytical model. The analytical model is in good agreement with both the simulations and experiments. In the experiments, a low R ON,sp of 53.3mΩ·cm 2 was realized under a high V B of 669.5 V, achieving a HOF LDMOS with high figure of merit FOM = V B 2 /R ON,sp of 8.41 MW/cm 2 .
- 20 April 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 68 (6) , 2861-2866
Total-Ionizing-Dose Radiation-Induced Dual-Channel Leakage Current at Unclosed Edge Termination for High Voltage SOI LDMOS
Total-ionizing-dose (TID) radiation response on unclosed edge termination is investigated for high voltage silicon-on-insulator (SOI) laterally diffused metal-oxide-semiconductor (LDMOS) in this article. Radiation-induced dual-channel leakage current model is proposed to reveal the mechanism of leakage current generation at OFF-state. Radiation causes a mass of positive oxide trapped charges generated in field oxide (FOX) layer and buried oxide layer. Owing to the P-SOI layer with significantly low doping concentration, two inversion channels are formed at the surface and bottom in the edge termination region, which provides parallel conduction paths. Electrons from the source N+ are pulled down and flow along the bottom channel while punchthrough occurring. The radiation-induced leakage current could be suppressed by thinning FOX layer, increasing the doping concentration of the P-SOI layer, and thickening the SOI layer.
- 20 April 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 68 (6) , 2861-2866
Total-Ionizing-Dose Radiation-Induced Dual-Channel Leakage Current at Unclosed Edge Termination for High Voltage SOI LDMOS
Total-ionizing-dose (TID) radiation response on unclosed edge termination is investigated for high voltage silicon-on-insulator (SOI) laterally diffused metal-oxide-semiconductor (LDMOS) in this article. Radiation-induced dual-channel leakage current model is proposed to reveal the mechanism of leakage current generation at OFF-state. Radiation causes a mass of positive oxide trapped charges generated in field oxide (FOX) layer and buried oxide layer. Owing to the P-SOI layer with significantly low doping concentration, two inversion channels are formed at the surface and bottom in the edge termination region, which provides parallel conduction paths. Electrons from the source N+ are pulled down and flow along the bottom channel while punchthrough occurring. The radiation-induced leakage current could be suppressed by thinning FOX layer, increasing the doping concentration of the P-SOI layer, and thickening the SOI layer.
- 25 March 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 68 (5) , 2372-2377
Analytical Design and Experimental Verification of Lateral Superjunction Based on Global Region Normalization Method
The global region normalization (GRN) method is proposed to optimize the lateral superjunction (SJ), in this article. The GRN features normalizations in the global doping range of the SJ from zero to the maximum doping concentration N max that was theoretically determined by the pillar width W SJ . Then the optimization covers all the possible design points of the SJ. For the SJ with given W SJ and pillar length L SJ , the specific ON-resistance R on,sp and breakdown voltage V B are normalized in the global region of the doping concentration N SJ . With the GRN method, the global normalization function f η is deduced to reflect the quantitative variation trend of R on,sp - V B and a design formula of the optimized N SJ is presented. Furthermore, lateral SJ devices were fabricated according to the formula. The measured R on,sp values of the SJ devices are reduced by almost 35% when compared with the theoretical limit of the triple RESURF device in a voltage range of 100-400 V. The experiments also reveal that the measured net R on,sp of the SJ region approaches the R on.sp ∝ V B 1.03 relationship.
- 25 March 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 68 (5) , 2372-2377
Analytical Design and Experimental Verification of Lateral Superjunction Based on Global Region Normalization Method
The global region normalization (GRN) method is proposed to optimize the lateral superjunction (SJ), in this article. The GRN features normalizations in the global doping range of the SJ from zero to the maximum doping concentration N max that was theoretically determined by the pillar width W SJ . Then the optimization covers all the possible design points of the SJ. For the SJ with given W SJ and pillar length L SJ , the specific ON-resistance R on,sp and breakdown voltage V B are normalized in the global region of the doping concentration N SJ . With the GRN method, the global normalization function f η is deduced to reflect the quantitative variation trend of R on,sp - V B and a design formula of the optimized N SJ is presented. Furthermore, lateral SJ devices were fabricated according to the formula. The measured R on,sp values of the SJ devices are reduced by almost 35% when compared with the theoretical limit of the triple RESURF device in a voltage range of 100-400 V. The experiments also reveal that the measured net R on,sp of the SJ region approaches the R on.sp ∝ V B 1.03 relationship.
- 11 March 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 68 (6) , 2354-2367
A Fast-Transient Low-Dropout Regulator With Current-Efficient Super Transconductance Cell and Dynamic Reference Control
A fast-transient, current-efficient low-dropout regulator (LDO) with super transconductance cell (STC) is proposed in this paper. By adopting advanced current amplifier (CA) and dynamic biasing (DB) techniques for the error amplifier (EA), the feedback loop bandwidth can be significantly extended without increasing much quiescent power, which reduces output voltage spikes and response time greatly. Moreover, dynamic reference control (DRC) with robust loop stability is embedded in the LDO to adaptively adjust voltage reference during transient so as to further enhance the slew rate of EA, realizing significant enhancement for the transient performances. This circuit has been implemented in a 0.35μm CMOS process and occupies an active chip area of 456×278 μm 2 . Experimental results show that it is able to provide 100mA load current at 200mV dropout voltage, with current efficiency of 99.88%. The output voltage spike under maximum load current change in 20ns edge time is less than 11.2mV with a 0.054μs response time. The power-supply rejection (PSR) at 100kHz is -75.6dB.
- 11 March 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 68 (6) , 2354-2367
A Fast-Transient Low-Dropout Regulator With Current-Efficient Super Transconductance Cell and Dynamic Reference Control
A fast-transient, current-efficient low-dropout regulator (LDO) with super transconductance cell (STC) is proposed in this paper. By adopting advanced current amplifier (CA) and dynamic biasing (DB) techniques for the error amplifier (EA), the feedback loop bandwidth can be significantly extended without increasing much quiescent power, which reduces output voltage spikes and response time greatly. Moreover, dynamic reference control (DRC) with robust loop stability is embedded in the LDO to adaptively adjust voltage reference during transient so as to further enhance the slew rate of EA, realizing significant enhancement for the transient performances. This circuit has been implemented in a 0.35μm CMOS process and occupies an active chip area of 456×278 μm 2 . Experimental results show that it is able to provide 100mA load current at 200mV dropout voltage, with current efficiency of 99.88%. The output voltage spike under maximum load current change in 20ns edge time is less than 11.2mV with a 0.054μs response time. The power-supply rejection (PSR) at 100kHz is -75.6dB.