Xin Ming
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Xin Ming has a total of 57 co-authors. Here are the top co-authors by number of shared publications:
- Bo Zhang
University of Electronic Science and Technology of China
13 shared publications - Yao Qin
State Key Laboratory of Electronic Thin Films and Integrated Devices, UESTC, Chengdu, China
6 shared publications - Mo Huang
University of Macau
5 shared publications - Zhi-Yi Lin
State Key Laboratory of Electronic Thin Films and Integrated Devices, UESTC, Chengdu, China
5 shared publications - Zhuo Wang
State Key Laboratory of Electronic Thin Films and Integrated Devices, University of Electronic Science and Technology of China, Chengdu, China
5 shared publications - Rui Paulo Martins
University of Macau
4 shared publications
Latest Publications
- 31 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. PP (15498328) , 1-14
An Up to 10-MHz 6.8% Minimum Duty Ratio GaN Driver With Adaptive Short-Pulse High-CMTI Level Shifter and Dual-Switch Bootstrap Techniques
Level shifter and floating power supply for high-side channel are major challenges in high-voltage high-frequency DC-DC converters. This paper presents an up to 10 MHz GaN driver suitable for high-power-density automotive electronics. An adaptive short-pulse (ASP) high d $V_{\text {sw}}$ /d $t$ noise immunity level shifter (LS) with efficient analog noise blanker (ANB) is proposed, achieving 6.8 ns minimum on-time at 10 MHz $f_{\text {sw}}$ . A dual-MOS-switches bootstrap (DMSB) circuit is proposed to ensure that the bootstrap (BST) rail achieves saturation (>80%) at 10 MHz frequency by sensing $V_{\text {sw}}$ and the low-side gate drive signal. To validate this work, a half-bridge GaN driver has been fabricated in a $0.5~\mu $ m 80 V HV CMOS process and the active area is $1.44\times 1.42$ mm2. The d $V$ /d $t$ immunity has been verified both in Buck converter and double pulse conditions, which is up to 46 V/ns at 60V Buck converter and 56 V/ns at 48 V double pulse topology. The proposed DMSB technique achieves a peak efficiency of 86.7% at 10 MHz for 12-to-5V conversion, representing a 6.7% improvement over the conventional approach.
- 31 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. PP (15498328) , 1-14
An Up to 10-MHz 6.8% Minimum Duty Ratio GaN Driver With Adaptive Short-Pulse High-CMTI Level Shifter and Dual-Switch Bootstrap Techniques
Level shifter and floating power supply for high-side channel are major challenges in high-voltage high-frequency DC-DC converters. This paper presents an up to 10 MHz GaN driver suitable for high-power-density automotive electronics. An adaptive short-pulse (ASP) high d $V_{\text {sw}}$ /d $t$ noise immunity level shifter (LS) with efficient analog noise blanker (ANB) is proposed, achieving 6.8 ns minimum on-time at 10 MHz $f_{\text {sw}}$ . A dual-MOS-switches bootstrap (DMSB) circuit is proposed to ensure that the bootstrap (BST) rail achieves saturation (>80%) at 10 MHz frequency by sensing $V_{\text {sw}}$ and the low-side gate drive signal. To validate this work, a half-bridge GaN driver has been fabricated in a $0.5~\mu $ m 80 V HV CMOS process and the active area is $1.44\times 1.42$ mm2. The d $V$ /d $t$ immunity has been verified both in Buck converter and double pulse conditions, which is up to 46 V/ns at 60V Buck converter and 56 V/ns at 48 V double pulse topology. The proposed DMSB technique achieves a peak efficiency of 86.7% at 10 MHz for 12-to-5V conversion, representing a 6.7% improvement over the conventional approach.
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 61 (10) , 1-13
A Nesting-Connected Reconfigurable SC Converter With Fine-Grained Conversion Ratios and Increased Output Conduction Paths for On-Chip Surround Power Delivery
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 61 (10) , 1-13
A Nesting-Connected Reconfigurable SC Converter With Fine-Grained Conversion Ratios and Increased Output Conduction Paths for On-Chip Surround Power Delivery
- 5 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 61 (6) , 2752-2763
A Segment-Interlace Multi-Phase Hybrid Converter With Concurrent Inductor Energizing and Inherent Current Balancing
This article presents a segment-interlace (SI) multiple-phase (MP) hybrid converter for 12-V bus to point-of-load (PoL) conversion. This topology achieves key features that are typically difficult to realize together in conventional MP hybrid converters: 1) concurrent charging of all inductors; 2) wide voltage conversion ratio (VCR) range; and 3) inherent auto-balancing of inductor currents and flying capacitor voltages. We first analyze the rationale behind the auto balance in the inductor currents. Next, we propose the SI converter, detailing its evolution from conventional 3-path-4-state (3P4S) converter and its working principles across different VCR ranges. Then, we prove that the SI approach is compatible with multiple hybrid topologies. Its capability of downsizing switching frequency enables comparable efficiency as conventional phase shedding. Fabricated in a 180-nm bipolar-CMOS-DMOS (BCD) process, the prototype three-phase SI converter achieves a measured peak efficiency of 92.9% and an $I_{\mathrm { L}}$ imbalance within 1.5%. The concurrent charging enables the lowest normalized output undershoot among compared designs.
- 5 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 61 (6) , 2752-2763
A Segment-Interlace Multi-Phase Hybrid Converter With Concurrent Inductor Energizing and Inherent Current Balancing
This article presents a segment-interlace (SI) multiple-phase (MP) hybrid converter for 12-V bus to point-of-load (PoL) conversion. This topology achieves key features that are typically difficult to realize together in conventional MP hybrid converters: 1) concurrent charging of all inductors; 2) wide voltage conversion ratio (VCR) range; and 3) inherent auto-balancing of inductor currents and flying capacitor voltages. We first analyze the rationale behind the auto balance in the inductor currents. Next, we propose the SI converter, detailing its evolution from conventional 3-path-4-state (3P4S) converter and its working principles across different VCR ranges. Then, we prove that the SI approach is compatible with multiple hybrid topologies. Its capability of downsizing switching frequency enables comparable efficiency as conventional phase shedding. Fabricated in a 180-nm bipolar-CMOS-DMOS (BCD) process, the prototype three-phase SI converter achieves a measured peak efficiency of 92.9% and an $I_{\mathrm { L}}$ imbalance within 1.5%. The concurrent charging enables the lowest normalized output undershoot among compared designs.
- 31 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41 (4) , 4653-4666
A Current-Efficient Fast-Transient PMOS LDO With Aux-Path Push-Pull Buffer and Shaped-Hybrid-Bias Technique Achieving 8.15 ps FoM
A current-efficient and fast-transient p-channel metal-oxygen-semiconductor (PMOS) low-dropout regulator designed for high-speed high-current load transient in mobile applications is presented. A low-power aux-path push-pull buffer is applied to provide both high push and pull current for gate-capacitance (CgP) of power field-effect transistor (FET), hence significantly suppressing both undershoot and overshoot, and the aux-path further accelerates the transient response. Meanwhile, a shaped-hybrid-bias (SHB) circuit, implementing a novel hybrid scheme, regulates the range of error amplifier’s bias current and combines the advantage of adaptive bias and dynamic bias. DC accuracy and stability under heavy load are well-maintained. Thus, a higher mirror ratio can be utilized, which contributes to achieving higher bandwidth and response speed. This circuit was implemented in a 0.18-μm CMOS process and occupies a silicon area of 400 × 250 μm2. With a 1 μF output capacitor and 18 μA quiescent current, load transient test results with 200 mV VDROP show that it features 19/14 mV of undershoot/overshoot at load transient under 270 mA load step (tedge = 300 ns).
- 31 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41 (4) , 4653-4666
A Current-Efficient Fast-Transient PMOS LDO With Aux-Path Push-Pull Buffer and Shaped-Hybrid-Bias Technique Achieving 8.15 ps FoM
A current-efficient and fast-transient p-channel metal-oxygen-semiconductor (PMOS) low-dropout regulator designed for high-speed high-current load transient in mobile applications is presented. A low-power aux-path push-pull buffer is applied to provide both high push and pull current for gate-capacitance (CgP) of power field-effect transistor (FET), hence significantly suppressing both undershoot and overshoot, and the aux-path further accelerates the transient response. Meanwhile, a shaped-hybrid-bias (SHB) circuit, implementing a novel hybrid scheme, regulates the range of error amplifier’s bias current and combines the advantage of adaptive bias and dynamic bias. DC accuracy and stability under heavy load are well-maintained. Thus, a higher mirror ratio can be utilized, which contributes to achieving higher bandwidth and response speed. This circuit was implemented in a 0.18-μm CMOS process and occupies a silicon area of 400 × 250 μm2. With a 1 μF output capacitor and 18 μA quiescent current, load transient test results with 200 mV VDROP show that it features 19/14 mV of undershoot/overshoot at load transient under 270 mA load step (tedge = 300 ns).
- 23 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41 (4) , 4740-4755
A Monolithic GaN Laser Diode Driver With Steep-Edge Driving Current for LiDAR Transmitters Using a 3 × Self-Circulating Charge Pump
Direct time-of-flight light detection and ranging is widely used for real-time, long-range three-dimensional sensing. It requires narrow optical pulses with high peak power to achieve high detection resolution and long range, imposing high demands on the laser diode driver (LDD) in the LiDAR transmitter. Monolithic GaN integration is well-suited for LDD design, as it minimizes gate-drive loop parasitics and offers devices with superior figures of merit. However, conventional GaN-based gate drivers suffer from limited driving capability due to the lack of suitable p-type devices. This article presents an FET-controlled LDD based on a 0.25-μm GaN-on-Silicon process. A 3× self-circulating charge pump and zero-voltage-drop fast-charging switches strengthen the predriver, enabling high-speed switching of the GaN control switch. Experimental results show that the proposed LDD achieves a 10 A peak driving current with fast edge transitions of 434 ps (rise) and 252 ps (fall). Dead time insertion and an on-chip filtering capacitor suppress shoot-through current in the final stage of the predriver. The LDD exhibits an average power loss of 420 mW at 10 MHz and achieves a peak efficiency of 92.44% .
- 23 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41 (4) , 4740-4755
A Monolithic GaN Laser Diode Driver With Steep-Edge Driving Current for LiDAR Transmitters Using a 3 × Self-Circulating Charge Pump
Direct time-of-flight light detection and ranging is widely used for real-time, long-range three-dimensional sensing. It requires narrow optical pulses with high peak power to achieve high detection resolution and long range, imposing high demands on the laser diode driver (LDD) in the LiDAR transmitter. Monolithic GaN integration is well-suited for LDD design, as it minimizes gate-drive loop parasitics and offers devices with superior figures of merit. However, conventional GaN-based gate drivers suffer from limited driving capability due to the lack of suitable p-type devices. This article presents an FET-controlled LDD based on a 0.25-μm GaN-on-Silicon process. A 3× self-circulating charge pump and zero-voltage-drop fast-charging switches strengthen the predriver, enabling high-speed switching of the GaN control switch. Experimental results show that the proposed LDD achieves a 10 A peak driving current with fast edge transitions of 434 ps (rise) and 252 ps (fall). Dead time insertion and an on-chip filtering capacitor suppress shoot-through current in the final stage of the predriver. The LDD exhibits an average power loss of 420 mW at 10 MHz and achieves a peak efficiency of 92.44% .
- 8 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 61 (5) , 2263-2275
A Monolithic GaN Driver With Power-Rail Charging Saturation Bootstrap Technique Achieving Enhanced Slew Rate and Gate Rise/Fall Time Ratio of 1.28
A monolithic gallium nitride (GaN) driver with power-rail charging saturation bootstrap (PCSB) technique is proposed in this article. The proposed driver features an internal PCSB driver to significantly improve the gate slew rate of GaN power switch through the combined action of embedded cross-coupled charge pump (ECCP) and $3V_{\mathrm {DD}}$ biasing stage. Transmission speed enhancement and shoot-through current elimination are also realized in the PCSB driver. Moreover, an integrated GaN overcurrent protection (OCP) circuit with a high-speed high-precision (H2) GaN comparator is implemented for GaN power switch and realizes high-speed OCP with enhanced accuracy. The proposed driver is fabricated in a GaN-on-SOI process and occupies an active chip area of 4.7 mm2. The experimental results show that the deviation of the ratio of gate rise-to-fall time of power GaN (=1.28) from the ratio of the designed static peak sink-to-source current (=1) is as low as 28%, indicating stronger output pull-up capability than prior arts. Benefiting from this, the proposed driver achieves 96% peak efficiency for a 15-W LED driver. The short-circuit protection response time of only 43 ns is realized by the proposed OCP circuit.
- 8 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 61 (5) , 2263-2275
A Monolithic GaN Driver With Power-Rail Charging Saturation Bootstrap Technique Achieving Enhanced Slew Rate and Gate Rise/Fall Time Ratio of 1.28
A monolithic gallium nitride (GaN) driver with power-rail charging saturation bootstrap (PCSB) technique is proposed in this article. The proposed driver features an internal PCSB driver to significantly improve the gate slew rate of GaN power switch through the combined action of embedded cross-coupled charge pump (ECCP) and $3V_{\mathrm {DD}}$ biasing stage. Transmission speed enhancement and shoot-through current elimination are also realized in the PCSB driver. Moreover, an integrated GaN overcurrent protection (OCP) circuit with a high-speed high-precision (H2) GaN comparator is implemented for GaN power switch and realizes high-speed OCP with enhanced accuracy. The proposed driver is fabricated in a GaN-on-SOI process and occupies an active chip area of 4.7 mm2. The experimental results show that the deviation of the ratio of gate rise-to-fall time of power GaN (=1.28) from the ratio of the designed static peak sink-to-source current (=1) is as low as 28%, indicating stronger output pull-up capability than prior arts. Benefiting from this, the proposed driver achieves 96% peak efficiency for a 15-W LED driver. The short-circuit protection response time of only 43 ns is realized by the proposed OCP circuit.
- 11 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 61 (1) , 366-377
Phase-Scalable CF-Cross-Connected-Based Hybrid DC-DC Converter With Auto VCF Balancing and Inactive CF Charging
This article presents a multiple-phase (MP) flying ${C}_{\mathrm { F}}$ -cross-connected (CCC)-based hybrid dc-dc converter for 12-V input to point-of-load (PoL) conversion. First, we illustrate the evolution of the proposed MP CCC converter from the conventional two-phase (2P) CCC converter. The proposed topology enables easy scalability in the number of active phases with the finest granularity. Second, we compare potential “ ${I}_{\mathrm { L}}$ -balance” and “ ${V}_{\mathrm { CF}}$ -balance” control schemes, selecting the “ ${V}_{\mathrm { CF}}$ -balance” one for its higher efficiency and wider voltage conversion ratio (VCR) range. Third, in light-load conditions where certain phases are disabled and their ${C}_{\mathrm { F}}$ s are discharged by leakage currents, this topology facilitates an inactive- $C_{\mathrm { F}}$ charging scheme. This prevents overstress on inactive switches and mitigates large inrush charging currents upon reactivation of ${C}_{\mathrm { F}}$ s. Fabricated in a 180-nm bipolar-CMOS-DMOS (BCD) process, the prototype four-phase converter achieves measured peak efficiency of 90.3% and 91.6% at 1.2- and 1.8 V- ${V}_{\mathrm { O}}$ , respectively. The easy scalability extends the VCR range and the load current range with high efficiency. Furthermore, it is suited for fault-tolerant schemes.
- 11 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 61 (1) , 366-377
Phase-Scalable CF-Cross-Connected-Based Hybrid DC-DC Converter With Auto VCF Balancing and Inactive CF Charging
This article presents a multiple-phase (MP) flying ${C}_{\mathrm { F}}$ -cross-connected (CCC)-based hybrid dc-dc converter for 12-V input to point-of-load (PoL) conversion. First, we illustrate the evolution of the proposed MP CCC converter from the conventional two-phase (2P) CCC converter. The proposed topology enables easy scalability in the number of active phases with the finest granularity. Second, we compare potential “ ${I}_{\mathrm { L}}$ -balance” and “ ${V}_{\mathrm { CF}}$ -balance” control schemes, selecting the “ ${V}_{\mathrm { CF}}$ -balance” one for its higher efficiency and wider voltage conversion ratio (VCR) range. Third, in light-load conditions where certain phases are disabled and their ${C}_{\mathrm { F}}$ s are discharged by leakage currents, this topology facilitates an inactive- $C_{\mathrm { F}}$ charging scheme. This prevents overstress on inactive switches and mitigates large inrush charging currents upon reactivation of ${C}_{\mathrm { F}}$ s. Fabricated in a 180-nm bipolar-CMOS-DMOS (BCD) process, the prototype four-phase converter achieves measured peak efficiency of 90.3% and 91.6% at 1.2- and 1.8 V- ${V}_{\mathrm { O}}$ , respectively. The easy scalability extends the VCR range and the load current range with high efficiency. Furthermore, it is suited for fault-tolerant schemes.
- 28 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 59 (2) , 583-594
An NMOS LDO With TM-MOS and Dynamic Clamp Technique Handling Up To Sub-10-μs Short-Period Load Transient
A current-efficient and fast-transient n-type low-dropout regulator (LDO) for high-frequency load transient in mobile phone applications is presented in this article. By using transconductance magnified MOS (TM-MOS), it reduces LDO’s output impedance with fast response speed and keeps high current efficiency. Moreover, based on load-current sensing of TM-MOS, active clamp strategy is implemented to optimize the driving dead zone (DDZ) of this NMOS LDO and achieve good high-frequency load transient performance. Robust loop stability for a wide load-current range is ensured as well with the help of revised Type-II frequency compensation. This circuit has been implemented in a 0.35-$\mu$ m standard CMOS process and occupies an active chip area of 470$\times$ 280$\mu$ m$^{2}$ . With a 1-$\mu$ F output cap and load steps between 0 A and 300 mA, experimental results show that it features 50/36 mV of undershoot/overshoot at low-frequency load transient and 68/36 mV of undershoot/overshoot at the high-frequency load transient (i.e., 10-$\mu$ s light-load duration). This regulator consumes 8.2-$\mu$ A quiescent current, achieving 99.68% equivalent current efficiency at 300-mA load current.- 28 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 59 (2) , 583-594
An NMOS LDO With TM-MOS and Dynamic Clamp Technique Handling Up To Sub-10-μs Short-Period Load Transient
A current-efficient and fast-transient n-type low-dropout regulator (LDO) for high-frequency load transient in mobile phone applications is presented in this article. By using transconductance magnified MOS (TM-MOS), it reduces LDO’s output impedance with fast response speed and keeps high current efficiency. Moreover, based on load-current sensing of TM-MOS, active clamp strategy is implemented to optimize the driving dead zone (DDZ) of this NMOS LDO and achieve good high-frequency load transient performance. Robust loop stability for a wide load-current range is ensured as well with the help of revised Type-II frequency compensation. This circuit has been implemented in a 0.35-$\mu$ m standard CMOS process and occupies an active chip area of 470$\times$ 280$\mu$ m$^{2}$ . With a 1-$\mu$ F output cap and load steps between 0 A and 300 mA, experimental results show that it features 50/36 mV of undershoot/overshoot at low-frequency load transient and 68/36 mV of undershoot/overshoot at the high-frequency load transient (i.e., 10-$\mu$ s light-load duration). This regulator consumes 8.2-$\mu$ A quiescent current, achieving 99.68% equivalent current efficiency at 300-mA load current.- 1 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 70 (5) , 2215-2227
A 50-V 50-MHz High-Noise-Immunity Capacitive-Coupled Level Shifter With Digital Noise Blanker for GaN Drivers
In this paper, a high-noise-immunity capacitive-coupled level shifter with digital noise blanker (DNB) is presented for GaN drivers. During and after d $V$ /dt transitions, the DNB blanks the common mode noise induced by d $V$ /dt and converts the differential mode noise due to mismatch effect to common mode noise. This enables high d $V$ /dt immunity of 200V/ns and high mismatch tolerance not less than 15%. Moreover, a dynamic discharge control (DDC) circuit prevents coupling capacitor from charging the floating power rail within a wide negative d $V$ /dt transition range and achieves fast reset for high frequency operation. High speed, low power consumption and down to $-$ 5V negative floating power rail tolerance are also achieved. The proposed level shifter is fabricated in a 0.5- $\mu$ m BCD process and occupies an active chip area of 0.051mm $^{2}$ . Experimental results confirm that the proposed level shifter works at 50V 50MHz, achieving power consumption of 27.3pJ/transition and 1.26ns average delay with a small figure of merit (5.5(pJ $\cdot$ ns)/( $\mu $ m $^{3}\cdot$ V)). The effect of the DDC is confirmed within negative d $V$ /dt transition range of $-$ 5V/ns $\sim$ $-$ 50V/ns.
- 1 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 70 (5) , 2215-2227
A 50-V 50-MHz High-Noise-Immunity Capacitive-Coupled Level Shifter With Digital Noise Blanker for GaN Drivers
In this paper, a high-noise-immunity capacitive-coupled level shifter with digital noise blanker (DNB) is presented for GaN drivers. During and after d $V$ /dt transitions, the DNB blanks the common mode noise induced by d $V$ /dt and converts the differential mode noise due to mismatch effect to common mode noise. This enables high d $V$ /dt immunity of 200V/ns and high mismatch tolerance not less than 15%. Moreover, a dynamic discharge control (DDC) circuit prevents coupling capacitor from charging the floating power rail within a wide negative d $V$ /dt transition range and achieves fast reset for high frequency operation. High speed, low power consumption and down to $-$ 5V negative floating power rail tolerance are also achieved. The proposed level shifter is fabricated in a 0.5- $\mu$ m BCD process and occupies an active chip area of 0.051mm $^{2}$ . Experimental results confirm that the proposed level shifter works at 50V 50MHz, achieving power consumption of 27.3pJ/transition and 1.26ns average delay with a small figure of merit (5.5(pJ $\cdot$ ns)/( $\mu $ m $^{3}\cdot$ V)). The effect of the DDC is confirmed within negative d $V$ /dt transition range of $-$ 5V/ns $\sim$ $-$ 50V/ns.