Ravi Gugulothu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ravi Gugulothu has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
Naga Sarada Somanchi
JNTUH University College of Engineering, Science and Technology Hyderabad
4 shared publicationsNarsimhulu Sanke
Department of Mechanical Engineering , University College of Engineering, Osmania University , Hyderabad , India
4 shared publications- Narsimhulu Sanke
University College of Engineering, Osmania University
4 shared publications A. V. S. S. K. S. Gupta
JNTUH College of Engineering Hyderabad
1 shared publicationAchiya Khanam
North Dakota State University
1 shared publicationAhmed Farid
Institute of Nuclear Power Engineering Bangladesh University of Engineering and Technology Dhaka Bangladesh
1 shared publication
Latest Publications
- 29 October 2025
- Published by Springer Nature
- p. 361-376
Advances in Transfer Enhancement Techniques for Cutting-Edge Cooling Systems
- 29 October 2025
- Published by Springer Nature
- p. 361-376
Advances in Transfer Enhancement Techniques for Cutting-Edge Cooling Systems
- 3 May 2025
- Published by Springer Nature
- p. 300-314
Advancements in Biogas Production: Enhancing Efficiency Through Anaerobic Digestion Technologies
- 3 May 2025
- Published by Springer Nature
- p. 300-314
Advancements in Biogas Production: Enhancing Efficiency Through Anaerobic Digestion Technologies
- Open Access
- 6 October 2023
- Published by Walter de Gruyter GmbH in Energy Harvesting and Systems
- Vol. 11 (1)
Experimental investigations on heat transfer enhancement in a double pipe heat exchanger using hybrid nanofluids
Heat exchanger (HE) is an instrument that facilitates the operation of HE between two fluids that are at various temperatures. Double-pipe HEs are used in many organizations because of their low installation, design, maintenance costs, flexibility, and their suitability for high pressure applications. Heat transfer (HT) augmentation techniques (passive, active or compound techniques) are used in heat exchangers to reduce the HT surface area, to increase HT capacity and to reduce pumping power. Passive augmentation techniques are much cheaper and do not involve any external power input. They aim to improve the effective surface area, the residence time of the HT fluid and its thermal conductivity by the usage of nanofluids. Nanofluids are used for cooling applications in organizations, transportation, nuclear reactors, electrical and electronic devices and for biomedical applications. Hybrid nanofluids have higher thermal conductivity, low PD and frictional losses and pumping power as compared to the mono nanofluids. In this present work, experiments are conducted in a double pipe HE using TiO2, and SiC-water nanofluids by varying the volume concentration and cold fluid mass flow rate ranging from 17.5 to 34.5 lpm by making constant hot fluid mass flow rate. Further, experiments are conducted using TiO2–SiC/water hybrid nanofluids. Influence of nano and hybrid nanofluids on the overall HTC and friction factor are experimentally investigated. From the experiments, TiO2–SiC/water hybrid nanofluid with nanoparticle ratio TiO2:SiC = 1:2 is found to be optimum as the heat transfer enhancement is more with less improvement in friction factor. The overall heat transfer, and friction factor enhancement is 22.92 %, and 11.20 % higher respectively when compared with base fluid for TiO2:SiC = 1:2.
- 6 October 2023
- Published by Walter de Gruyter GmbH in Energy Harvesting and Systems
- Vol. 11 (1)
Open AccessExperimental investigations on heat transfer enhancement in a double pipe heat exchanger using hybrid nanofluids
Heat exchanger (HE) is an instrument that facilitates the operation of HE between two fluids that are at various temperatures. Double-pipe HEs are used in many organizations because of their low installation, design, maintenance costs, flexibility, and their suitability for high pressure applications. Heat transfer (HT) augmentation techniques (passive, active or compound techniques) are used in heat exchangers to reduce the HT surface area, to increase HT capacity and to reduce pumping power. Passive augmentation techniques are much cheaper and do not involve any external power input. They aim to improve the effective surface area, the residence time of the HT fluid and its thermal conductivity by the usage of nanofluids. Nanofluids are used for cooling applications in organizations, transportation, nuclear reactors, electrical and electronic devices and for biomedical applications. Hybrid nanofluids have higher thermal conductivity, low PD and frictional losses and pumping power as compared to the mono nanofluids. In this present work, experiments are conducted in a double pipe HE using TiO2, and SiC-water nanofluids by varying the volume concentration and cold fluid mass flow rate ranging from 17.5 to 34.5 lpm by making constant hot fluid mass flow rate. Further, experiments are conducted using TiO2–SiC/water hybrid nanofluids. Influence of nano and hybrid nanofluids on the overall HTC and friction factor are experimentally investigated. From the experiments, TiO2–SiC/water hybrid nanofluid with nanoparticle ratio TiO2:SiC = 1:2 is found to be optimum as the heat transfer enhancement is more with less improvement in friction factor. The overall heat transfer, and friction factor enhancement is 22.92 %, and 11.20 % higher respectively when compared with base fluid for TiO2:SiC = 1:2.
- Open Access
- 23 June 2023
- Published by Walter de Gruyter GmbH in Energy Harvesting and Systems
- Vol. 11 (1)
Experimental investigation of heat transfer characteristics for a shell and tube heat exchanger
In the present work, numerical investigations are conducted with 22 % cut segmental baffle heat exchanger (SB), 20°, 30°, and 40° helical baffles shell and tube heat exchangers (STHX) to estimate the overall heat transfer coefficient (OHTC), pressure drop (PD) and friction factor. Among the studied heat exchangers (HE), 40° helical baffles STHX provided the highest OHTC with minimum pressure drop. Hence, further investigations are conducted experimentally with 40° helical baffles STHX. OHTC increased by 2.65 % for 20° helical baffles, 5.37 % for 30° helical baffles, 9.78 % for 40° helical baffles when compared with 22 % cut segmental baffle heat exchanger. The deviation between experimental and numerical OHTC is 2.64 % 40° helical baffles.
- 23 June 2023
- Published by Walter de Gruyter GmbH in Energy Harvesting and Systems
- Vol. 11 (1)
Open AccessExperimental investigation of heat transfer characteristics for a shell and tube heat exchanger
In the present work, numerical investigations are conducted with 22 % cut segmental baffle heat exchanger (SB), 20°, 30°, and 40° helical baffles shell and tube heat exchangers (STHX) to estimate the overall heat transfer coefficient (OHTC), pressure drop (PD) and friction factor. Among the studied heat exchangers (HE), 40° helical baffles STHX provided the highest OHTC with minimum pressure drop. Hence, further investigations are conducted experimentally with 40° helical baffles STHX. OHTC increased by 2.65 % for 20° helical baffles, 5.37 % for 30° helical baffles, 9.78 % for 40° helical baffles when compared with 22 % cut segmental baffle heat exchanger. The deviation between experimental and numerical OHTC is 2.64 % 40° helical baffles.
- 16 May 2023
- Published by Wiley in Heat Transfer
- Vol. 52 (6) , 4422-4449
Augmentation of heat transfer through passive techniques
The thermal performance of energy preservation systems is greatly improved by increasing miniaturization and boosting. These are imaginative (or Promethean) techniques to enhance heat transfer. Enhancement methods of heat transfer draw great attention in front of the industrial sector because of their ability to provide energy savings and raise the economic efficiency of thermal systems. Three techniques these methods are categorized; those are active, passive, and compound. Different types of components are used in passive methods because of the transfer/working fluid flow path to the enhancement of the heat transfer rate. In this article, the subject of the review was the passive heat transfer enhancement methods including inserts (conical strips, winglets, twisted tapes, baffles), porous materials, coil/helical/spiral tubes, rough surfaces (corrugated/ribbed surfaces), extended surfaces (fins) and nanofluids (mono and hybrid nanofluid). Recent passive heat transfer enhancement techniques are studied in this article as they are cost‐effective and reliable, and also comparably passive methods do not need any extra power to promote the energy conversion systems' thermal efficiency than active methods. In the passive approaches, various components are applied to the heat transfer/working fluid flow path to improve the heat transfer rate. The passive heat transfer enhancement methods studied in this article include inserts (twisted tapes, conical strips, baffles, winglets), extended surfaces (fins), porous materials, coil/helical/spiral tubes, rough surfaces (corrugated/ribbed surfaces), and nanofluids (mono and hybrid nanofluid). From the pioneers' research work, it is clear that a lower twist ratio and lower pitch, lesser winglet angles can provide more heat transfer rate and a little bit more friction factor. In the case of nanofluids, a little bit of pumping power is enhanced. Finally, heat transfer enhancement is compared with the thermal performance factor, which is more than unity.
- 16 May 2023
- Published by Wiley in Heat Transfer
- Vol. 52 (6) , 4422-4449
Augmentation of heat transfer through passive techniques
The thermal performance of energy preservation systems is greatly improved by increasing miniaturization and boosting. These are imaginative (or Promethean) techniques to enhance heat transfer. Enhancement methods of heat transfer draw great attention in front of the industrial sector because of their ability to provide energy savings and raise the economic efficiency of thermal systems. Three techniques these methods are categorized; those are active, passive, and compound. Different types of components are used in passive methods because of the transfer/working fluid flow path to the enhancement of the heat transfer rate. In this article, the subject of the review was the passive heat transfer enhancement methods including inserts (conical strips, winglets, twisted tapes, baffles), porous materials, coil/helical/spiral tubes, rough surfaces (corrugated/ribbed surfaces), extended surfaces (fins) and nanofluids (mono and hybrid nanofluid). Recent passive heat transfer enhancement techniques are studied in this article as they are cost‐effective and reliable, and also comparably passive methods do not need any extra power to promote the energy conversion systems' thermal efficiency than active methods. In the passive approaches, various components are applied to the heat transfer/working fluid flow path to improve the heat transfer rate. The passive heat transfer enhancement methods studied in this article include inserts (twisted tapes, conical strips, baffles, winglets), extended surfaces (fins), porous materials, coil/helical/spiral tubes, rough surfaces (corrugated/ribbed surfaces), and nanofluids (mono and hybrid nanofluid). From the pioneers' research work, it is clear that a lower twist ratio and lower pitch, lesser winglet angles can provide more heat transfer rate and a little bit more friction factor. In the case of nanofluids, a little bit of pumping power is enhanced. Finally, heat transfer enhancement is compared with the thermal performance factor, which is more than unity.
- 8 November 2022
- Published by Walter de Gruyter GmbH in Energy Harvesting and Systems
- Vol. 10 (2) , 365-375
A numerical study of water based nanofluids in shell and tube heat exchanger
This numerical investigation is made to estimate the effect of Al2O3 and Cu nanofluids on heat transfer rate, friction factor and thermal performance factor of a shell and tube heat exchanger. Mass flow rates of shell side (water) fluid are varied. Water based nanofluids are used inside the tubes with 0.01, 0.03, and 0.05% volume concentrations of Al2O3 and Cu nanofluids. Nusselt number obtained from the present investigation is compared with Dittus–Bolter equation and Pongjet Pomvonge et al. and found to be in good agreement with a maximum deviation of 3%. The Nusselt number of the dispersed nanofluids increased with the increase of nanofluids volume concentrations and shell side mass flow rate. In this study, maximum enhancement in Nusselt number is 7.50%, 8.65%, and 9.61% for Al2O3, and 1.46%, 2.23%, and 3.18% for Cu nanofluid respectively at 0.01, 0.03, and 0.05% volume concentrations were compared to base fluid as water. Friction factor is highest by 58.00% at 0.05% volume concentration of Cu/H2O nanofluid when relate to Al2O3/H2O nanofluid. Thermal Enhancement factor achieved is highest for Al2O3/H2O nanofluid.
- 8 November 2022
- Published by Walter de Gruyter GmbH in Energy Harvesting and Systems
- Vol. 10 (2) , 365-375
A numerical study of water based nanofluids in shell and tube heat exchanger
This numerical investigation is made to estimate the effect of Al2O3 and Cu nanofluids on heat transfer rate, friction factor and thermal performance factor of a shell and tube heat exchanger. Mass flow rates of shell side (water) fluid are varied. Water based nanofluids are used inside the tubes with 0.01, 0.03, and 0.05% volume concentrations of Al2O3 and Cu nanofluids. Nusselt number obtained from the present investigation is compared with Dittus–Bolter equation and Pongjet Pomvonge et al. and found to be in good agreement with a maximum deviation of 3%. The Nusselt number of the dispersed nanofluids increased with the increase of nanofluids volume concentrations and shell side mass flow rate. In this study, maximum enhancement in Nusselt number is 7.50%, 8.65%, and 9.61% for Al2O3, and 1.46%, 2.23%, and 3.18% for Cu nanofluid respectively at 0.01, 0.03, and 0.05% volume concentrations were compared to base fluid as water. Friction factor is highest by 58.00% at 0.05% volume concentration of Cu/H2O nanofluid when relate to Al2O3/H2O nanofluid. Thermal Enhancement factor achieved is highest for Al2O3/H2O nanofluid.
- 30 June 2022
- Published by Springer Nature
- p. 167-187
Thermal Hydraulic Performance of Helical Baffle Shell and Tube Heat Exchanger Using RSM Method
- 30 June 2022
- Published by Springer Nature
- p. 167-187
Thermal Hydraulic Performance of Helical Baffle Shell and Tube Heat Exchanger Using RSM Method
- 30 June 2022
- Published by Springer Nature
- p. 83-98
Numerical Investigation of Baffle Spacing in a Shell and Tube Heat Exchanger with Segmental Baffle
- 30 June 2022
- Published by Springer Nature
- p. 83-98
Numerical Investigation of Baffle Spacing in a Shell and Tube Heat Exchanger with Segmental Baffle
- 7 February 2022
- Published by Wiley in Heat Transfer
- Vol. 51 (5) , 3768-3793
Effect of helical baffles and water‐based Al2O3, CuO, and SiO2nanoparticles in the enhancement of thermal performance for shell and tube heat exchanger
In this study, Shell and tube heat exchanger (STHX) with 22% cut segmental baffles and helical baffles with 20°, 30°, 40° inclination angles are considered for three‐dimensional CFD analysis using the ANSYS FLUENT tool to investigate the performance of STHX. OHTC and comprehensive performance index are higher for 40° helical baffles when compared to segmental baffle and 20°, 30° helical baffle heat exchangers with water as working fluid. Hence, further investigations are carried out for 40° helical baffle heat exchangers. Numerical investigations are extended with nanofluids (Al2O3, CuO, and SiO2) at 1%, 3%, and 5% volume concentrations for each nanofluid. Under the same mass flow rates, 40° helical baffles with Al2O3nanofluid as working fluid provided better heat transfer rates when compared to the other two nanofluids and base fluid. Also, the authors noticed that the 5% volume (vol) concentration nanofluids provided better heat transfer enhancements when compared to 1%, 3% volume concentrations, and base fluid. Enhancements (10.33%–8.24%) from lower to the higher mass flow rate in 40° HB with Al2O3nanofluid at 5% volume concentration are observed when compared to water as base fluid.
- 7 February 2022
- Published by Wiley in Heat Transfer
- Vol. 51 (5) , 3768-3793
Effect of helical baffles and water‐based Al2O3, CuO, and SiO2nanoparticles in the enhancement of thermal performance for shell and tube heat exchanger
In this study, Shell and tube heat exchanger (STHX) with 22% cut segmental baffles and helical baffles with 20°, 30°, 40° inclination angles are considered for three‐dimensional CFD analysis using the ANSYS FLUENT tool to investigate the performance of STHX. OHTC and comprehensive performance index are higher for 40° helical baffles when compared to segmental baffle and 20°, 30° helical baffle heat exchangers with water as working fluid. Hence, further investigations are carried out for 40° helical baffle heat exchangers. Numerical investigations are extended with nanofluids (Al2O3, CuO, and SiO2) at 1%, 3%, and 5% volume concentrations for each nanofluid. Under the same mass flow rates, 40° helical baffles with Al2O3nanofluid as working fluid provided better heat transfer rates when compared to the other two nanofluids and base fluid. Also, the authors noticed that the 5% volume (vol) concentration nanofluids provided better heat transfer enhancements when compared to 1%, 3% volume concentrations, and base fluid. Enhancements (10.33%–8.24%) from lower to the higher mass flow rate in 40° HB with Al2O3nanofluid at 5% volume concentration are observed when compared to water as base fluid.
- 12 January 2022
- Published by Wiley in Heat Transfer
- Vol. 51 (3) , 2645-2666
Use of segmental baffle in shell and tube heat exchanger for nano emulsions
Among the heat exchangers (HE), the shell and tube type is being widely used in different applications like oil, chemical, and power plant Industries. The incorporation of segmental baffles (SB) improves the HE capacity from higher temperature fluid to lower temperature fluid. Nanofluids can be effectively used to enhance the heat transfer rate. In this study, numerical simulations have been carried out in a shell and tube heat exchanger (STHX). Among HE design methods, Tubular Exchanger Manufacturers Association (TEMA) standard is being used for better design by many researchers. In this paper, the computational fluid dynamics analysis was carried out with Al2O3, CuO, and SiO2 nanofluids amid 1, 3, and 5 vol. % with water emulsion to enhance the heat transfer coefficient of STHX. The nanofluid has been used in the cold fluid of the HE and on the other side hot water is used. From the results, it is noticed that with the increase of Nanofluids, the value of heat transfer coefficients is found to be increasing. The overall heat transfer coefficient has been enhanced for Al2O3, CuO, and SiO2 about 10.41%, 12.27%, and 9.56%, respectively, at 0.22 kg/s for the 5 vol. % addition. It is also depicted that the pressure drop is increasing with the incorporation of nanofluids.
- 12 January 2022
- Published by Wiley in Heat Transfer
- Vol. 51 (3) , 2645-2666
Use of segmental baffle in shell and tube heat exchanger for nano emulsions
Among the heat exchangers (HE), the shell and tube type is being widely used in different applications like oil, chemical, and power plant Industries. The incorporation of segmental baffles (SB) improves the HE capacity from higher temperature fluid to lower temperature fluid. Nanofluids can be effectively used to enhance the heat transfer rate. In this study, numerical simulations have been carried out in a shell and tube heat exchanger (STHX). Among HE design methods, Tubular Exchanger Manufacturers Association (TEMA) standard is being used for better design by many researchers. In this paper, the computational fluid dynamics analysis was carried out with Al2O3, CuO, and SiO2 nanofluids amid 1, 3, and 5 vol. % with water emulsion to enhance the heat transfer coefficient of STHX. The nanofluid has been used in the cold fluid of the HE and on the other side hot water is used. From the results, it is noticed that with the increase of Nanofluids, the value of heat transfer coefficients is found to be increasing. The overall heat transfer coefficient has been enhanced for Al2O3, CuO, and SiO2 about 10.41%, 12.27%, and 9.56%, respectively, at 0.22 kg/s for the 5 vol. % addition. It is also depicted that the pressure drop is increasing with the incorporation of nanofluids.