JMJhon Edison Goez Mora

Jhon Edison Goez Mora

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Jhon Edison Goez Mora has a total of 18 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Validation in diabetic rats of a fully automated insulin delivery system based on impulsive offset-free MPC control

    by Jhon E. Goez-Mora, Natalia Arbelaez-Córdoba, Norman Balcazar-Morales, Pablo S. Rivadeneira

    The development of an impulsive automated insulin delivery system (i-AiDS) for type 1 diabetes mellitus aims to provide real-time blood glucose regulation with minimal human intervention. This study presents the validation of an offset-free impulsive zone model predictive control strategy designed to cope with external disturbances such as meal intake and plant-model mismatch in a diabetic rat model. Fourteen male Wistar rats induced diabetes with streptozotocin were monitored using an continuous glucose monitoring and regulated by delivering insulin with a customized low-cost pump. After acquiring diabetes condition, the procedure for installing the devices in the rat is carried out. During the first day, manual insulin injections are made by the pump, the glucose response is recorded by the interface and an off-line parametric estimation is executed. Based on the parameters found, simulations are used for the first tuning of the controller and the estimator. During the second day, the parameters of the model and the control are tested and adjusted. Finally, on the third day, a 72-hour test of the impulsive begins in full autonomous mode. Results showed that the controller achieved an average of 83.4% of the time within the target range of 80-180 mg/dL, with no severe hypoglycemic or hyperglycemic events. The median absolute relative difference between model predictions and actual sensor data was 24.66%, indicating the presence of plant-model mismatch that was effectively handled by the controller. Peak hyperglycemic events reached 320 mg/dL, but were regulated within 50 minutes, while mild hypoglycemic events occurred in 3.62 ± 1.8 cases per subject. The study demonstrates the efficacy of the controller in managing unannounced carbohydrate intake and physiological disturbances in a real-world preclinical environment. These findings provide a foundation for future clinical trials, emphasizing the importance of in vivo validation of control strategies to refine the i-AiDS for human use. Improvements in model accuracy and dynamic parameter tuning could further enhance performance, particularly in longer experimental periods.

  • Open Access

    Study of insulin infusion in diabetic rats with an ultra‐low‐cost insulin pump for managing blood glucose levels

    by Jhon E. Goez‐Mora, Natalia Arbelaez‐Córdoba, Norman Balcazar‐Morales, Pablo S. Rivadeneira

    Introduction: This study assesses the accuracy of an ultra‐low‐cost insulin pump for regulating blood glucose, an essential component of the artificial pancreas. Objectives: The primary objective is to assess the accuracy of blood glucose regulation using an ultra‐low‐cost insulin pump compared with insulin injections. Methods: The study was conducted using 14 male Wistar rats aged 14 weeks, which were induced with diabetes through a streptozotocin procedure. The control group (seven subjects) was treated with subcutaneous insulin injections, and the study group (seven subjects) was treated with the experimental insulin pump. Results: Our findings reveal that the ultra‐low‐cost insulin pump performs comparably to insulin injections for glycemia regulation using standard clinical insulin treatment. The blood glucose records obtained by CGM indicate that trends in both methods correspond, with a glycemia median absolute relative difference of 6.1748 mg/dL and an interquartile range of 14.57 mg/dL. The response time to reach glucose levels between 70 and 180 mg/dL was around 55 min, testing different amounts of insulin units ranging from 0.09 to 2.06 U. Also, four obstruction cases were detected by the system in an average time of 3 s, showing compliance with the EN60601‐2‐24 standard. Conclusions: The in vivo experiments with diabetic rats and ultra‐low‐cost insulin pumps demonstrate that these prototypes can be used for glucose regulation in clinical trials while complying with the conditions of the EN60601‐2‐24 standard. Future work should focus on conducting insulin pump tests in a closed loop and a cybersecurity study to prevent any possible external attack.


  • Open Access

    Efficient AiDS Through Real-Time Insulin Sensitivity Estimation and Energy Management with Event-Triggered MPC

    by Jhon E. Goez-Mora, Pablo S. Rivadeneira

    This study focuses on developing a fully Automated Insulin Delivery System (AiDS) based on an event-triggered Model Predictive Control (ET-MPC) strategy aimed at individuals with type 1 diabetes mellitus (T1DM). The research addresses two key questions: (1) Can glycemic regulation be enhanced by integrating the recursive least squares (RLS) parameter estimator by dynamically adjusting the insulin sensitivity parameter, and (2) Can the embedded systems’ energy efficiency and operational autonomy by using an ET-MPC strategy? The ET-MPC strategy was enhanced with an RLS insulin sensitivity estimation. It was implemented within a hardware-in-the-loop (HIL) framework on a Raspberry Pi model 3B, integrated with a customized low-cost insulin pump and a battery driver. The virtual patient in the HIL emulation is the UVA/Padova simulator, which adds realistic physiological conditions to the emulation, such as highly nonlinear dynamics, measurement noise, parametric variations following the circadian cycle, and carbohydrate disturbances not announced to the controller. The prediction model was identified from 10 adults of the simulator and the states retrieved by the Kalman estimator. The study compared the performance of time-triggered (TT) and ET control strategies, both with and without the RLS insulin sensitivity estimator, over three-day HIL emulations. The integration of RLS improved glucose regulation under TT control, increasing the time within the target range from 75.97 to 91.08%. When the ET strategy is activated, it can reduce the control actions up to 60% while maintaining acceptable glycemic performance. Consequently, energy consumption was significantly reduced, with the device’s operational time extended up to threefold. However, higher thresholds in ET control compromised glucose control, highlighting the trade-off between energy savings and control performance. The RLS estimator enhances glycemic regulation, and the ET strategy achieves substantial energy savings, making the AiDS more efficient and portable. Future work should explore alternative estimation techniques for improved robustness and the real-time adaptation of the $$\epsilon$$ ϵ and $$\lambda$$ λ thresholds to optimize the trade-off between glycemic regulation and energy expenditure.


  • Open Access

    Technological Development of CNC Machine Tool for Machining Soft Materials

    by Laura Tobon Ospina, Carlos Alberto Vergara Crismatt, Juan David Arismendy Pulgarin, Sebastian Correa Zapata, Yomin Estiven Jaramillo Munera, Jhon Edison Goez Mora, Juan Camilo Londoño Lopera, John Sneyder Tamayo Zapata, Carlos Eduardo Palacio Laverde, Edgar Mario Rico Mesa

    In recent years, the process carried out in the GACIPE research group is related to the development of the base technology of the manufacturing and metalworking industry. The machine tools that are vital for the consolidation and competitiveness of the industry in any country has been approached through two approaches: The design and construction of the new machine. In this aspect, the modeling of the structure and the displacements’ parameterization allows defining the precision of the movements and the rational use of energy. The adaptation and repowering of a used machine. In this approach, the recovery and technological updating proposed to recover its performance, becoming an excellent alternative to improving and perfecting the production of a company. In both cases, the CNC milling machine tools are controlled by free software. The application proposed is mechanized in soft materials.

  • Open Access

    Implementation of an Artificial Vision System for Welding in the Retrofitting Process of a Robotic Arm Industrial

    by Yomin Estiven Jaramillo Munera, Jhon Edison Goez Mora, Juan Camilo Londoño Lopera, Edgar Mario Rico Mesa

    An industrial approach to the use of artificial vision is worked, and we are searching for the improvement of the welding process using a robotic arm. These kinds of robots in the last years have been associated to high accuracy tasks like classification, welding, object manipulation, assembly, and so on. Generally, the artificial vision is not used in works which use manipulator arm; this is normally due to the robot programmer who plans the robot task, which is executed cyclically, however, there are some approaches where different tasks using artificial vision are implemented. In this chapter, we present a retrofitting process of a manipulator welder arm Miller MR-2000, and the development of an artificial vision system, which could be used in the positioning of the machine. The developed system is able to look for areas suitable for the welding task between two pieces of material within a workspace; this process is possible using techniques of computational vision and image processing. Subsequently, the algorithm calculates the number of welding points based on the area identified previously, and finally, it sends the respective coordinates by means of G code to the robot for welding the pieces.


  • Automatic Visual Classification of Parking Lot Spaces: A Comparison Between BoF and CNN Approaches

    by Jhon Edison Goez Mora, Juan Camilo Londoño Lopera, Diego Alberto Patiño Cortes


  • Positioning of the Cutting Tool of a CNC Type Milling Machine by Means of Digital Image Processing

    by Juan Camilo Londoño Lopera, Jhon Edison Goez Mora, Edgar Mario Rico Mesa